AIM:CALCULATING THE DESIGN MIX FOR M35 CONCRETE WITH FLY ASH AND M50 WITH OUT FLY ASH AS PER IS CODES.      GIVEN DATA:(ASSUMED) *0PC 43 GRADE CEMENT(IS8112) *20MM SIZE AGGREGATE,ZONE 1 FINE AGGRGATE *SEVERE ENVIRONMENT CONDITION *ADMIXTURE SELECTED AS PER IS3812-PART-1(FLY ASH) *SLUMP VALUE 100MM…

Structural drawings required at site are *General Note – an overview of all the codes, procedures, and abbreviations, etc required to give a comprehensive guide to getting to work on the construction site. This includes concrete mix, details for other structural drawings, lengths and construction types of each…

Design and Draft a layout of a residential building with the following details: a. Plot Size: 60’x20’(18.3m x6m)  b. Orientation- Facing East  c. Develop the following: 1. Architectural Drawing (Floor Plan, Elevations, and Sections) 2. Structural Drawing (Column, Bean, Footing Plan) AIM: To Design and Draft a layout of…

Aim: To create: Template, inserting text and attributes Doors of warehouse and placing it in blocks Electrical legend and making it blocks Different types of door for residential project Drawing bars, making it as block and making it as a table as bar bending schedule.   Commands used:  Block. Insert. Attributes. Field.…

Q1. Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks wherever required. Provide appropriate dimensions in the plan. Assume the size of doors, appliances and others as per the standards.     Aim: To Create the Kitchen Layout and to Also, use proper dimension techniques…

1.AIM: To Create a layout of the Plan and Section A of the project in Challenges 7. *To create layout of plan and section using Template mArch.dwt. *To create viewport using MV command of size 400x445 and 375x445 and setting the scale (1:50) *Editing Attributes in the template.Take a plot using A1 size. Procedure: *In…

AIM: To create 3D model and view of:   *Furniture element   *Isolated footing   *AASTHO type girder   *Drop column with panel   *A wall PROCEDURE:    *Open the AutoCAD, click on workspace switching and change it to 3d modelling and click on the home button near the view cube.   *Set the limits and zoom - all.   DRAWING…

1.Aim: To create the 3D isometric view of a building with plan and elevation given: Procedure: *Initially, open the AutoCAD and go to 3D modelling. *Then set the units of the drawing as engineering (feet and inches). *Now set the limits: *Now, in the AutoCAD take the top view and intially draw the plan as given in the…

                                                                                       PROJECT 2 …

1.AIM To create a ceiling in the first floor level. INTRODUCTION: From the architectural tab to model a ceiling at the first floor level on the saved week 3 project of the residential unit. PROCEDURE: STEP 1) OPEN MODEL Launch the Revit software. STEP 2) CREATE CEILING Go to Project Browser expand Ceiling…

Q1)  Aim:  To Select the type of structure need to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School Type of structure OFFICE BUILDING   Q2) AIM : Assuming reasonable assumptions…

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. AIM: Need to create sinusoidal point then curve from the point and then create surface. INTRODUCTION: By using dynamo created a sinusoidal point then created a curve from the point and converted into the surface.…

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class. AIM: To use the architecture/ structure project file  to export revit architecture and structural model…

1. Write the steps involved to upload a .std file through web mail?   Steps involved to upload a .std file through web mails are as follows; Open the STAAD pro software and locate the share option available on the introduction screen. After clicking on the share button, select send mail option. Then, browse for the.…