AIM : For the given Hood model, Take the mid surface for all the components after checking the geometrical errors and mesh the mid surface with the given element Quality criteria. (Refer the table Below for the Quality criteria)   GIVEN: S.No  Quality Criteria  Value  1 Target/Average length   5 2 Minimum Length  2 3 Maximum…

AIM: For the given CCB CAD model, Check for the Geometry cleanup (if required), Take the mid surface, and Mesh it with the below 2D element Quality criteria.  GIVEN: S.No  Quality Criteria  Value  1 Target/Average length   5 2 Minimum Length  3 3 Maximum Length  7 4 Aspect …

AIM: using the given quality criteria,to obtain good quality meshing of given compnent.   TO GIVEN: Follow the below-mentioned quality criteria, mesh the component given below, and assign thickness: Target Element Length = 5 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5…

AIM : For the given Plastic Bottle Cap model, check for the geometrical errors and take the mid surface by suitable mid surfacing techniques. PID and Thickness assignment has to be done for all the mid surfaces. Mesh the same with the given element Quality criteria. (Refer to the table below for the Quality criteria) TO…

1. For the given Plastic Bottle Cap model, check for the geometrical errors and take the mid surface by suitable mid surfacing techniques. PID and Thickness assignment has to be done for all the mid surfaces. Mesh the same with the given element Quality criteria. (Refer to the table below for the Quality criteria)  …

For the given Rear view mirror component, check for the geometrical errors and mesh the Surfaces with the given 2D element Quality criterias given below.    S.No  Quality Criteria  Value  1 Target/Average length   1 2 Minimum Length  0.5 3 Maximum Length  2   Use tetra elements to mesh the Volumes defined in the model…

      AIM:  Pre-processing of the car instrument panel using ANSA KEYWORDS: Mid-surface Extraction, Shell Meshing. OBJECTIVE:   Introduction to shell meshing i.e. 2D meshing Geometry check & Topological error clean up  Mid surface generation  Meshing the geometry  The quality criterion to be followed: ABSTRACT: In this…

Deploying Connectors for a Rear Door of a Car   Aim - To Deploy a appropriate connectors for a Rear Door of a Car. Objective - Creating a property id's for door hinges and deploy a bolt connectors. Creating RBE2 1D Elements for bolt joints. Creating RBE3-CBUSH-RBE3 element for the weather strips. Creating RBE3-HEXA-RBE3…

AIM: To study and create 1D element on the given component. OBJECTIVE: To Mesh the Given component with the Size of 5 Units. Create 1D elements on the following component with given cross-section and DOF. a. Rod element:- Translational DOF should be Constrained with RBE2 link Cross-Section: BOX- Dimension a= 12 mm    …

given:Target Element Length = 5 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2 Units 6 Max. Length 8 Units 7 Min angle Quad 45 8 Max angle Quad 135 9 Min angle Tria 20 10 Max angle Tria 120 10 Tria %  10  …

AIM:-  To extract the mid surface and generate the mesh on the Car Backdoor model in Hypermesh Procedure:-  Step 1- Importing and Geometry Cleanup - Import the Model .igs file as geometry. - Visualize the model if it has any deformities in its surface or free edges, which can be visualized in wireframe mode & By Topo mode.…

  AIM: Meshing of Rear Wheel Holder.   Target Element Length = 5 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2 Units 6 Max. Length 8 Units 7 Min angle Quad 45 8 Max angle Quad 135 9 Min angle Tria 20 10 Max angle…

1. AIM: Mesh the Plastic model in Hypermesh. 2. OBJECTIVES OF THE PROJECT:           As per the given Quality criteria mesh the Below model. S.N Quality Criteria  Value  1 Target Element Length  5 mm 2 Aspect Ratio  3 3 Skewness 45 4 Warping 30 5 Taper     …

For the given MODEL 1, Create a Teramesh for Housing component with the following quality criteria. TetraMesh Generation Method: 2D to 3D Conversion Elements sizes: Min- 2 Units, Target- 5 Units, Max- 7 Units  Tet collapse: 0.15   OBJECTIVE: TO CREATE A TETRA MESH FOR HOUSING COMPONENT WITH GIVEN QUALITY CRITERIA. Given…

Objective:- To mesh the given geometry based on the given parameter and create connectors and attach to the various parts of the given model. Create connectors and attach them to the various parts of the given model:- 1. Right_Rail_2 & Front_truss_1:- Seam-Quad(angled+capped+L) 2. Left_Rail_2 &…

AIM: - To mesh the given door trim panel along with all its feature like ribs, dog-house etc. using Hyper mesh.   OBJECTIVE: To Extract the mid surface. To Capture the features and dog-house properly. To Mesh the mid surface with the given element Quality criteria and maintaining proper mesh flow.     Given Quality Criteria:…

Aim: Writing a detailed report of unit conversion as per different standards followed in different industries.   Objective: To convert the unit to gm, mm, and ms in the calculation. Other Standards units can be formed in the table form.   Conversion of S.I units gm, mm, ms Given Units: MASS = 1kg   …