ASSIGNMENT 5 OBJECTIVE: Create a mesh for bumper…

https://drive.google.com/open?id=1NZ6Lc11FOdB9ZkS5gshuYoUlMk1e0zC4

objective:1.the speed of sound in a rail 2. The length of the rail is about 1000 mm.calculate the time takes for a shock wave to travel from one end of the rail to the other. 3.Time for sound to travel length of rail=______ 4.Edit the engine file so that the stress wave can be monitored, moving from one…

  https://drive.google.com/open?id=1KKcr-vXc3phPgONyvj1gKKepcLsYz1OI https://drive.google.com/open?id=1bcbq0j71fCVXwAy-n4lCE6940yKrO1R9      

objective: 1follow the recommended properties as per intructions. 1.Using the crash beam file from the previous assignment, change the run time to 55 ms. 2. Change the number of animation steps during simulation to a minimum of 25 and maximum of 60. 3. Run the base simulation without any modification to element properties.…

https://drive.google.com/open?id=1KH_PiRZC7bO4QJw2Fy5GG4nUcn9P01Fl

https://drive.google.com/open?id=1JfuUYWulz7UNAc9geXzo27QJYZE0rbCG https://drive.google.com/open?id=1c-TDTwWW5eDuSREavt2Cr_YBuy4BJQkD  

Objective: 1.Import the geometry  2.clean up the geometry of given models 3.Extract the mid surface from models 4.Fill the holes less than 5mm 5.create the 2d mesh with minimum size of element having 5mm to 7.5mm 6.move the mesh to original geometry PROCEDURE MODEL-1 brackets 1.import the geometry The imported geometry…

https://drive.google.com/file/d/1mdmAbkO5s2qf2BUOuBo3pF6lUJyGTi54/ https://drive.google.com/open?id=1FskzH1v2D8vjS6H-ecwB8yRI3mC2Ul9m https://drive.google.com/open?id=135w15hdTakwTZFwTNG6QQYUEEV_yKyhZ https://drive.google.com/open?id=1xGEL1ERen3RJNmb90j9FkAKCXkCVfZmD https://drive.google.com/open?id=1W7R8V7gia6CBftkVXrOyZL9lGz80GKqD…

https://drive.google.com/open?id=1aernS1M6jnG8cJpdLl3kcoZjJ1IzCdt7 https://drive.google.com/open?id=10RTyFNRC3mGrZitAwl45VWU8gmkkwhKI  

AIM: To perform the side crash analysis using            1.create a proper interface            2.create a rigid wall with 0.1 friction           3.Assign a proper weight to model and use add masses to reach target weight 700 kg while…

Aim: To analyse the front crash analysis for a given neon car and find out the outputs of shot gun forces, pillar forces, intrusions, accelerations on rocker below B-pillar. Given conditions: Check unit system and either follow[Mg mm s] or [Kg mm ms]. Create appropriate interface ,friction 0.2 and recommended parameters.…

Aim:- Extract the mid surface for given Sheetmetal component and mesh the component, assign the quality criteria as per given parameters.  S.No                Parameters                             …

Aim:- Extract the mid surface for given Sheetmetal component and mesh the component, assign the quality criteria as per given parameters.   S.No                                                 …

Aim:-  For the given Rear view mirror component, check for the geometrical errors and mesh the Surfaces with the given 2D element Quality criterias given below.  S.No                        Quality…

Objective: Mesh the sheet metal component called front panel assign quality parameters as per the given criteria.                                                   Procedure: - Checked the geometry…

Aim:-  For a given component, check the geometrical errors, extracting mid surface and perform quality checks and assign proper thickness for the component.                                                                 Procedure: Introduction for the part: The given component Ip console, it is a plastic interior automotive…

Aim: Create conections for side door and PIDS for the component.