:         To create a Base Bracket Plastic Component through a given Class A Surface and perform Draft Analysis on the final plastic component. PROCEDURE : Creation of Tooling Axis. Creation of Class B and Class C surface. Creating a solid part out of surface molding. Draft Analysis of Class A…

Aim The aim of this project is to develop the product design of the switch bezel with the help of the class A surface following the OEM standard.  The Thickness of the component is Considered as  2.5 mm MATERIAL USED: Polyester:             It is a category of polymers that…

AIM: To create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of the component to be 2.5…

AIM:      Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of the component to…

AIM : To create the Core and cavity blocks for the Switch Bezel Component. OBJECTIVE : To Create Core, Cavity and Parting surface for the given component along the Tooling Axis. CORE : Core is a preformed, bonded, sand insert placed into the mold to shape the interior of a casting or a part of the casting that cannot be…

AIM: Create the rib for the Drill Handle considering the design rules.   Tooling Axis creation: It is defined as the direction in which the mould/core and cavity open. Selection of the direction of the tooling axis depends on the ease at which components can be easily ejected. By analysing the component the most easily…

AIM:  Create the rib for the Drill Handle considering the design rules.   Tooling Axis creation: It is defined as the direction in which the mould/core and cavity open. Selection of the direction of the tooling axis depends on the ease at which components can be easily ejected. By analysing the component the most easily…

Aim: Create the Dog House for the Door Trim considering the design rules and perform the draft analysis for class A and create the final close body component and perform the draft analysis. Objective: Create the Tooling axis  Design the class-B and class-C surfaces and join them. Use the Close Surface feature…

Aim: To Create the Door trim lower component through the given Class-A surface. Objectives: • Creation of Tooling axis with appropriate draft angle. • Creation of other surfaces (eg, B and C surfaces) for creating a solid component. • Perform Draft analysis on Class A surface and Solid model hence created.…

AIM:     Create the Pillar, Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.    CLASS A SURFACE:    …

UNDERBODY COTING:                                   Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just…

BENCHMARKING Benchmarking is a process of measuring the performance of a company’s products, services, or processes against those of another business considered to be the best in the industry, “best in class.” The point of benchmarking is to identify internal opportunities for improvement. By studying…

AIM - To create the Door trim panel's CAD model considering the inputs given to me following the design rules and OEM standards. ABSTRACT - The project deals with the explanation of steps and procedures followed while developing the Door Trim Panel of a car using CATIA V5. Using the class A surface I was able to create…

AIM: To Use the Section from Hood design and calculate the Section Modulus using the formula  S = I/y  Where,  S = Section Modulus I = Moment of Inertia y = distance between the neutral axis and the extreme end of the object    PROCEDURE: The data are collected from taking the master section using…

Hood Design in CATIA V5:Objective:Design hood outer panel, inner panel and reinforcements with the given outer hood skin, master section and design parameters. Introduction:The hood or bonnet is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment (or trunk on rear-engine…

Aim: Calculate the Wheel Arch gap at required points and check whether the car passes the European standard. Introduction:                                      Wheel Arch is the semi-circular part of the fender…

Modelling of various mounting points on the fender.   Objective:To design various mounting points on the fender, according to the design parameters.     Introduction: Fender:Fender's purpose is to prevent rocks, mud, sand, liquids from being thrown into the air or on to the pedestrians by a rotating wheel.…

INTRODUCTION:  The roof of a car or other vehicle is the top part of it, which protects passengers or goods from the weather. The roof also protects the passenger from any injury when the car gets crashed or is rolled over or something heavy falls on the roof.     OBJECTIVE: The mian objective of this project…

  AIM:  Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip. Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html) Tyco…

AIM: To solve the above assignment questions and define the necessary electrical properties in the respective workbench. OBJECTIVE: To download the P-Clamp CAD data and define it as Electrical Support in the Electrical Part design workbench and also define the necessary electrical properties.To download…

AIM- To prepare a flattened-view of a previously created harness assembly OBJECTIVE- The objective of this project is to create a flattened-view for a harness assembly and then place it on the drawing sheet. It is desired that the bundles with protective coverings are represented with different visuals on the drawing sheet.…

AIM- To prepare a flattened-view of a previously created harness assembly OBJECTIVE- The objective of this project is to create a flattened-view for a harness assembly and then place it on the drawing sheet. It is desired that the bundles with protective coverings are represented with different visuals on the…

Aim: Using the provided styling surface to come up with a back door design and  using appropriate design methodologies and make the necessary reinforcements and embosses .    A door is a hinged part which is used for entry and exit of the vehicles. Back doors are one of the type doors of the vehicle which are located next…

WIRING HARNESS FOR ENGINE AIM: To route the wiring harness for the given engine. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. INTRODUCTION: WIRING HARNESS OR CABLE HARNESS: A cable harness, also known as…

AIM: To route the wiring harness for the given Tailgate. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. INTRODUCTION: WIRING HARNESS OR CABLE HARNESS: A cable harness, also known as a wire harness, wiring harness, cable…