OBJECTIVE:To create the given 1d elements with a given cross sections and with a given degrees of freedom and allocate the respective 1d elements to the respective slots that provided in the parallel bracket and join the bracket with spring elements. PROCEDURE:  1.To import the model of iges file into the hypermesh…

OBJECTIVE:To create the mesh for the given component with as per given quality criteria and assign the thickness and extract the midsurface for the each of the component. PROCEDURE: 1.Import the geometry model and then extract the mid surface of the component and make the geometry cleanup manually and use the mid surface…

 objective:create the tetra mesh and 3d mesh for the given model with a given quality criterias. procedure:1. Import the given geometry and clean up and defeature the surface fillets with a min and max radius of the model. HOUSING MODEL 2. After importing the model mesh the given model with a 2d mesh with a given…

objective:To create the connector and attach the various parts of the given model. procedure:1.create the separate component for the different assemblies. 2.Mesh the given components with the suitable element size and make the suitable connection as given in the above components. Right rail2 and front truss 1:In this component…

objective: Mesh the given component with a given quality criteria and assign the thickness. procedure:1.Import the given geometry and then geometry clean up will be done  take the manual  mid surface for the component by offset the surface of the given component. 2.Take the given quality criteria as per the given…

objective:In the given component check the given geometry and mesh the component with a given quality criteria and then assign the thickness. procedure:1.first import the given model and then make the geometry checks of the geometry. 2. After the checks of the geometry if any errors that shown will be able to fix the issues…

objective:The  given component extract the mid surface and check the geometry errors and mesh the component with a given quality criteria and then assign the thickness. procedure:1. Import the given geometry and check for the geometry errors and then fix that issues and execute with a 100% the geometry should be cleaned.…

component switch panel : time =5hrs In this component some elements quality fails due to the minnimum size with a small features and also depends on the average element size and the maximum element size. 2 nd component :time=4hrs https://drive.google.com/file/d/15a_SLdusDhnNIRoSBcemHut_pCWumKop/view?usp=sharing https://drive.google.com/file/d/1JiDlPr3bxpCQu6YXZAGYsaVJ9LspVBpI/view?usp=sharing

objective:To check the given geometry checks and then mesh the model with a given quality criteria and remesh the component with a volume mesh. procedure: 1.Import the geometry and then check for the geometry errors and then fix if any geometrical errors by using the auto fix option. 2.Then mesh the given geometry with…

Time taken:4 hours

objective:For the given fe rear model different types of connections given at the different regions. procedure:1.for the given fe model import the model first . 2.Identify the regions that the seam weld and the spot weld connections where the surfaces to be parallel and perpendicular. seam weld It is having the two types…

objective:For the given component make the necessary morphing techniques that are available in the video. procedure:1.first import the geometry model as iges file and then do topo for that geometry . 2.After the topo check for the geometry checks and then fix the errors by auto fix or the manual method to fix the geometry…

objective: For the given geometry check the geometry errors and extract the midsurface and mesh the given component witha quality criteria and thickness of component is assigned. Procedure:1.Import the given model and then check for the given geometry errors and then fix it auto fix or manually . 2.Take the mid surface…

Aim:For the given assembly, check for the geometrical errors and mesh with the given element Quality criteria. After meshing the component the thickness has to be assigned for mid surfaces. Use tetra elements to model non-uniform thickness components. procedure: 1.Import the given model and then check for the geometry…

objective:For the given geometry clean up the geometry and then extract the midsurface and mesh the component witha a given quality criteria . procedure:1. Import the given geometry and then make the clean the geometry with that holes having the dia of 5mm ignore that holes. 2.After the geometry cleanup extract the midsurface…

1. Check the material properties of the rail component and calculate the speed of sound in steel rail=____5188_m/sec__ 2. The length of the rail is about 1000 mm.calculate the time takes for a shock wave to travel from one end of the rail to the other.  Ans:0.1927sec 3.Time for sound to travel length of…

objective:For the given component run the base simulation with given data and then change the properties for the component as given and then run the simulation and then compare the results. procedure:1.Import the given rad file first and then set the eng run time and the animation dt value. 2.After  import the rad…

objective:For the given components change the material cards and the properties as given in the videos and then run the simulation and then compare the results of the simulation. procedure-case-1: 1.Import the material model given - FAILURE_JOHNSON_0000.rad 2.open the properties in the browser and assign the best recommended…

objective:To mesh the given bumper system with a given average element size and run the crash tube model simulation with as per given in the questions  and plot the graphs and then compare the results. procedure: 1.Import the given bumper system assembly and then set the average element size as the 6mm and then mesh the…

objective:for the given assignment first made the model settings as per given in the questions and then run the simulation and then compare the results and plot the energy graphs and note the difference in the graphs. procedure: 1.Import the given model and then check for thre unit system is in [kg,mm,ms] and then check…

objective:For the given model of frontal crash run the simulation and obtain the results as per given in the question and then compare the obtained results and then compare those results. procedure: 1. First import the given model as the 0000.rad file and then check the starter file that has the unit system as [kg,mm,ms]…

objective:Design the plate with hole as per given in the cases1 and 2 per dimensions given and simulate the both the cases and then compare the results. procedure: case1 open the ansys work bench software and then go to the engineering data and select the material which is suitable for the simulation of these components.…

objective: For the given materials applied for the spur gear and then run the simulation and compare the results and decide which material is recommended based on the results. Spur gears or straight-cut gears are the simplest type of gear. These gears mesh together correctly only if fitted…

objective: For the given bevel gear perform the simulation run for the 3 mesh sizes of 6,5,4mm and then compare the results of the 3 simulations. grid dependency test This is Grid dependency test, where, analysis begins with a coarse mesh and it is refined to finer mesh for each run until the results do not change significantly…

objective:To perform the static structural analysis on the rail wheel and track and then compare the results of the bearing load of 100000 with the 500000N and evaluate the results. procedure: 1.Import the geometry model and then check the material is assigned to the components and edit the model in the model section.…

objective:Simulate three different types of welding using three different weld materials and then compare the results obtained. procedure:1.first import the given geometry and then select the material as per given in the 3 cases. 2.create the new material for the bronze cast and the aluminium alloy using the option engineering…

objective:Sheet metal bending is to be performed for 3 different materials mentioned below. Variation of certain settings is also to be performed and your conclusions are to be added to the report and compare the results of the all the cases . procedure:1.In the case1 the material used is that aluminium alloy 1199 so to…

objective:For the given challenge setup the copper rolling operation and then simulate the rolling operation and then compare the results obtained during the simulation. procedure: 1.first add the material copper in the engineering data of the geometry of non linear materials to the library and the structural steel. 2.Import…

objective:For this challenge, you will have to perform an analysis to simulate the bending of a wire in ANSYS. You will have to use Copper Alloy (Non Linear), Aluminium Alloy (Non Linear) and Magnesium Alloy ( Non Linear) for the wire alone. You need to find out the Equivalent stress and Equivalent strain on the wire alone. …

objective:For this challenge use the structural steel for the shere and non linear structural steel for the plate and then  perform the analysis to simulate a sphere pressing on a plate. procedure: 1.In the enginerring data add the material as structural steel non linear to the libraray and import the geometry into…

objective:For this challenge, you will have to perform a transient analysis on a piston and cam mechanism model that has been provided to you You need to run the analysis with Frictionless contact, Frictional with 0.1 and 0.2 as the frictional contact for a total of 3 cases and then compare the results for…

objective:For this challenge, you will have to perform a transient structural analysis on a double universal joint with a spring using three different materials: Structural Steel, Stainless Steel and Titanium alloy and need to obtain the Equivalent stress and total deformation for all the three cases and compare them. …

objective: To  perform a transient structural analysis on a worm gear assembly and  you need to cut the gear by half so as to bring the model within limits and then obtain the results. procedure: case1:For the full gear simulation. Import the geometry and rename the geometry components as the worm and the gear and assign…

objective:To perform the explicit dynamics simulation for the 2 cases by changing the velocity of the cutting tool and then compare the results for both the cases. procedure: case1:cutting tool velcity of 20000mm/sec. 1.First edit the engineering data sources by adding the steel 1006 to the library and then import the…

objective:For this challenge, you will have to perform the tension and torsion test on the specimen provided and then simulate the both the tests and then compare the results. procedure: case1:Tensile test It is used to find out how strong a material is and also how much it can be stretched before it breaks.…

objective:For this challenge, you will have to simulate a bullet penetrating into a bucket. You will need to use 3 different non linear materials for the bucket and analyse their behaviour for the same velocity of bullet and then compare the results of the 3 cases. case1:Using the material aluminium alloy non linear as…

objective:For this challenge, you will have to perform a parametric study using 3 different values of thickness for the car body.Analyse the total deformation and Equivalent stresses acting on the model.  procedure: case1 :use the parameter thickness of 0.3 for car body 1.Edit the engineering data sources and add…