RCC beam and column design calculator (IS 456 and IS 13920)
Design an RC beam to IS 456:2000 (steel, bars that fit, moment of resistance of what you provide, links), work out the IS 13920:2016 sway shear Vu,a and Vu,b with the hoops over 2d, and detail a column: steel, axial capacity, confining length l0, link spacing and Ash. "Check my numbers" tests the values in an ETABS detailing report. Free, no sign-up, runs in your browser.
IS 456:2000 · IS 13920:2016 with Amendments 1 (2017) and 2 (2020) · checked against an independent solution (2,732 checks at build) · Updated 22 Nov 2026
Section
Materials and bars
Factored actions
Bars are written count-diameter: "3-20 + 2-16". Leave them blank and the calculator picks the fewest bars of the chosen diameter. d comes from the layer setting (two layers: 25 mm bars apart by the larger of 15 mm, 2/3 aggregate and the bar); type d to use your own.
Span and gravity shear
Moments of resistance at the ends
Section and bars
The numbers in your report
Pre-filled with the most common answer in the challenge reports: Vu,a = 46 kN (no sign), Vu,b = 230 kN, links at 100 mm.
Defaults: the ETABS challenge beam as the reports read it from their models (clear span 4.725 m, 1.2(DL + IL) shear 92 kN, MuAs 174, MuBh 293, MuAh 236, MuBs 150 kN·m) and the 2-32 + 1-25 bars many of them provide. M25 and Fe415 are assumptions; set your own.
Column
Bars and links
The numbers in your report
Bars per face count the corners: 4 and 4 is 12 bars. "Legs across b" is how many link legs (outer link plus cross-ties) cross the b face; they must sit on bars evenly. Defaults: the 450 × 650 mm columns of the ETABS challenge with 12-25 bars for the 5,046 mm² the reports quote and 8 mm Fe500 links; the clear height and Pu are examples.
How do you design an RCC beam as per IS 456?
Find the limiting moment the section can take without compression steel, compare it with the factored moment, size the tension steel (and compression steel above the limit), check the steel limits, then design the links for the shear the concrete cannot carry. For the calculator's opening beam, 300 × 500 mm in M25 with Fe415 bars and Mu = 200 kN·m, d = 457 mm and Mu,lim = 216.1 kN·m.
- Limiting moment (Annex G-1.1 c), with xu,max/d = 0.53, 0.48 and 0.46 for Fe250, Fe415 and Fe500 (cl. 38.1). Fe550 is not in the table; the calculator uses 0.44, just below the 0.443 that the cl. 38.1 strain limit gives.
- Singly reinforced when Mu ≤ Mu,lim (Annex G-1.1 b solved for Ast): 1,477 mm² here, so 5-20 (1,571 mm²). Keep it between 0.85 bd/fy and 0.04 bD (cl. 26.5.1.1).
- Doubly reinforced above Mu,lim (Annex G-1.2). fsc is read off the design stress-strain curve of Fig. 23 at the strain of the compression bars, using SP 16 Table A's points for Fe415 and Fe500. SP 16 and NPTEL also subtract the concrete the bars displace (0.446 fck); the code text does not. Tick "SP 16" to match them.
- Bars that fit. Clear distance between bars in a layer at least the bar diameter and the aggregate size + 5 mm; a second layer at least 15 mm, 2/3 of the aggregate and the bar diameter above the first (cl. 26.3.2).
- Moment of resistance of the bars provided. The calculator finds the neutral axis from equilibrium with the strain in every bar (cl. 38.1) and flags xu > xu,max as over-reinforced. Here 224.9 kN·m with xu = 158 mm. This is the number IS 13920's sway shear needs.
- Shear (cl. 40): τc from Table 19 at the steel provided, τc,max from Table 20 (above it, enlarge the section), link steel fy taken as no more than 415 N/mm², spacing within 0.75d and 300 mm (cl. 26.5.1.5) and the minimum steel of cl. 26.5.1.6.
What is the sway shear formula in IS 13920:2016?
A beam in an earthquake frame must not fail in shear before it yields in bending. So clause 6.3.3 designs the links for the factored gravity shear, 1.2(DL + IL) on a simply supported span, plus the shear that holds the beam in balance when both ends have formed plastic hinges at 1.4 times their moments of resistance. Sway to the right puts a sagging hinge at A and a hogging hinge at B; sway to the left the opposite.
The design shear at each end is the larger of its two values, and never less than the analysis shear. With the ETABS challenge numbers:
For sway to the left, 1.4 × (236 + 150)/4.725 = 114.4 kN, so Vu,a = 206.4 kN. The design shears are 206.4 kN at A and 230.4 kN at B. Four things in the code are easy to miss:
- The sway-to-left signs were corrected. The 2016 print gave sway to the left the same signs as sway to the right. Amendment No. 2 (November 2020) changed them to + at A and − at B, as above.
- No concrete term. Clause 6.3.4 leaves out the concrete's shear strength: the links carry all of Vu. With 2-legged 8 mm Fe415 links that is 71 mm at B over 2d.
- 6 bar diameters, not 8. Over 2d from each face the spacing limit is the least of d/4, 6 times the smallest longitudinal bar and 100 mm; Amendment No. 1 (September 2017) replaced the print's 8 times. The first link sits within 50 mm of the face, and beyond 2d the limit is d/2.
- Moments of resistance, not analysis moments. MuAs and MuBh are what the bars provided can resist (IS 456). With the 2-32 + 1-25 bars at both faces the calculator gets 309 kN·m sagging and 309 kN·m hogging, so Vu,b rises to 275.2 kN. More steel than needed means more shear.
The calculator also runs the other beam rules of clause 6: at least two 12 mm bars and ρ ≥ 0.24√fck/fy on each face, ρ ≤ 2.5%, bottom steel at a column face at least half the top, every section at least a quarter of the larger top steel at the faces, b ≥ 200 mm, b/D > 0.3, D ≤ clear span/4, links at least 8 mm with 135° hooks of 8 diameters and 75 mm (Amendment 1), and laps: links at 150 mm or less over the lap, lap length at least Ld, no laps in a joint, within 2d of a face or in a quarter span next to a hinge, and no more than half the bars lapped at one section.
How do you calculate l0 and Ash for a column?
IS 13920 clause 7.6.1 (clause 8.1 before Amendment 1 renumbered it) puts closely spaced links over a length l0 at both ends of the column, next to each joint, where hinges could form. l0, the spacing and the bar area of the link all have their own rule:
h is the longer distance between parallel legs measured to their outer faces, and may not exceed 300 mm, which is why wide columns need cross-ties; Ak is the core measured to the link's outer faces, and Ash is the area of one leg. For the challenge's 450 × 650 mm column with 40 mm cover to the link, 12-25 bars and a leg on every bar, h = 217.3 mm and Ak = 370 × 570 = 2,10,900 mm². With 8 mm Fe500 links:
So 8 mm links go at 65 mm over l0 = 650 mm; 10 mm links (78.5 mm²) allow 103 mm and the 100 mm limit governs. Between the l0 zones the spacing limit is half the smaller side, 225 mm (cl. 7.4.2 d). Laps go only in the middle half of the clear height, with links at 100 mm or less over them (cl. 7.3.2.1), no more than half the bars lapped at a section, and none for bars over 32 mm. The confining links continue 300 mm into the footing (cl. 7.6.2).
The IS 456 side is checked too: 0.8-6% steel (cl. 26.5.3.1), short when le/D and le/b are both under 12 (cl. 25.1.2), and the axial capacity of cl. 39.3, which only applies when the minimum eccentricity is within 0.05 D:
The ETABS detailing challenges: what goes wrong
"Reinforcement Detailing of Beams from ETABS output" and "Reinforcement detailing of Columns from ETABS output" are challenges in Skill-Lync's ETABS building design courses. 342 public beam reports and 335 column reports carry those titles. We read them on 22 Nov 2026 and counted the patterns with scripts:
- The sign of Vu,a. Of the 83 beam reports that state a value of Vu,a, 54 give it as +45 to +48 kN; 1 keeps the minus sign. With their own numbers, 92 − 138.4 = −46.4 kN. Vu,b = 225-232 kN appears in 51.
- Units. 33 reports write the moments of resistance in kN, and 4 write the shears in kN·m.
- Gravity shear by direction. 16 reports use 92 kN for sway to the right and 74 kN for sway to the left. The 1.2(DL + IL) shear at an end does not change with the direction of sway; take the end values once and use them in both cases.
- l0. 5 column reports say l0 "should not be more than" the least lateral dimension, clear span/6 or 450 mm. It is a minimum, and the larger side, not the least, is the first term.
- Ash. 244 column reports mention special confining links, but only 5 work out Ash with numbers, and 3 of those 5 use h = 370 to 570 mm, the whole core side. With cross-ties h is the leg spacing, at most 300 mm.
- The 2016 print. 2 beam reports quote "8 times the smallest bar" for the 2d zone; none quote the 6 times of Amendment 1.
Paste your own values into "Check my numbers" in tabs 2 and 3 to see which of these apply.
How we checked the calculator
An independent Python script, scripts/verify/rcc_beam.py, rebuilds every calculation from the code text and this page refuses to build if the browser code differs from it in any of 2,732 numbers. It gets the sway shear from the statics of a free body (the gravity reactions plus the two hinge couples), not from the 6.3.3 formula, and finds the neutral axis by a different method. It integrates the parabolic-rectangular stress block of IS 456 Fig. 21 and gets 0.36 fck b xu at 0.416 xu, and rebuilds SP 16 Tables A, C, D and F. It also reproduces:
- IITK-GSDMA "Explanatory Examples for Ductile Detailing of RC Buildings" (Ingle and Jain, EQ22), Example 1: sway terms 1.4(286 + 377)/5 = 185.64 and 1.4(377 + 246)/5 = 174.44 kN, printed 186 and 175, and the end shears 103, 259, 270 and 92 kN (the example rounds every step up). Example 3, the 400 × 500 mm column: h = 188.5 mm, Ak = 1,46,496 mm², s = 84.2 mm (printed 84), l0 = 500 mm.
- NPTEL, IIT Kharagpur, "Design of Reinforced Concrete Structures": Mu,lim factors (Module 3 Lesson 5, Table 3.3), the doubly reinforced Q.1 of Module 4 Lesson 9 (fsc = 395.51 N/mm², Asc = 766.5 mm², printed 766.53) and Problem 4.1, the shear design of Module 6 Lesson 14 Problem 1 (τc = 0.706 N/mm², s = 95.25 mm), and the short column of Module 10 Lesson 22 Problem 1 (Asc = 2238.39 mm²).
The examples were written before the 2016 code, and the differences matter. IITK Example 1 follows IS 13920:1993: it subtracts the concrete's shear strength (2016 does not) and spaces links over 2d at 125 mm from d/4 = 133 and 8 × 16 = 128 mm; under 2016 with Amendment 1 the limit is 6 × 16 = 96 mm. Its 145 mm spacing for 145 kN of link shear does not follow from its own numbers: 2-legged 8 mm Fe415 links at d = 532 mm need 133 mm. In Example 3 the 2016 code adds the 0.05 s h fck/fy minimum (110 mm, does not govern) and caps the spacing at 6 × 16 = 96 mm in place of 1993's "75 to 100 mm". The IITK moments of resistance come from SP 16 tables and a T-beam for sagging; this calculator treats the section as rectangular, so its moments for those bars (276 sagging, 413 hogging) differ from the printed 286 and 377 kN·m. NPTEL's Problem 4.1 reads fsc from SP 16 Table F at d′/d = 0.11 (350.8 N/mm²); at the actual strain Table A gives 350.0 N/mm², and its step 2 has a typo (783.621 for 763.694 in the sum; the total, 2,572.834 mm², is right).
What this calculator does not cover
- Flanged beams. Sections are rectangular; a T-beam's sagging capacity is higher when the slab is in compression.
- Columns under moment. Tab 3 checks the axial capacity of cl. 39.3 and the detailing. Uniaxial and biaxial bending need the interaction diagrams of SP 16 (or ETABS); the strong-column weak-beam check (IS 13920 cl. 7.2) and the column shear of cl. 7.5 are not done here.
- Beam-column joints, shear walls, circular columns and spirals, torsion and deflection or crack-width checks.
- Gravity shear between the 2d zones is taken as varying linearly (a uniformly loaded span). Enter your own analysis shear if the loading is different.
The beam and column detailing challenges are part of Skill-Lync's ETABS courses, next to seismic analysis, SAFE foundation design and RCC detailing in AutoCAD.
Frequently asked questions
How do you design an RCC beam as per IS 456?
Take the effective depth d and find Mu,lim = 0.36 (xu,max/d)(1 − 0.42 xu,max/d) fck b d². If Mu is smaller the beam is singly reinforced and Ast comes from Annex G; if larger, add compression steel for Mu − Mu,lim. Keep Ast between 0.85bd/fy and 0.04bD, then design stirrups for Vu − τc b d.
What is the sway shear formula in IS 13920:2016?
Clause 6.3.3 adds the factored gravity shear 1.2(DL + IL) to the shear that holds the beam in equilibrium when both ends form plastic hinges: for sway to the right Vu,a = V(D+L) − 1.4(MuAs + MuBh)/LAB and Vu,b = V(D+L) + 1.4(MuAs + MuBh)/LAB. Sway to the left uses MuAh + MuBs with the signs reversed.
Why does Vu,a come out negative in the sway shear?
Because the hinge moments push the beam end down harder than gravity pushes it up. In the ETABS challenge 92 − 138.4 = -46.4 kN: the shear at A reverses for sway to the right. It does not govern the links (the larger end value does), but keep the sign so a checker can follow it.
What is the stirrup spacing near the column as per IS 13920?
Over a length of 2d from each column face the links may not be more than d/4, 6 times the smallest longitudinal bar or 100 mm (Amendment 1 of 2017 changed 8 times to 6 times), and the first link sits within 50 mm of the face. Beyond 2d the limit is d/2. Shear can need closer links.
How do you calculate special confining reinforcement Ash in a column?
For rectangular links IS 13920 clause 7.6.1 (c) asks Ash ≥ 0.18 s h (fck/fy)(Ag/Ak − 1) and ≥ 0.05 s h fck/fy. Ash is one leg of the link, h is the longer distance between parallel legs measured to their outer faces (not over 300 mm) and Ak is the core inside the link's outer faces.
What is the confining length l0 of a column?
l0 is the length from each joint face over which the closely spaced confining links go: not less than the larger column dimension, one-sixth of the clear height and 450 mm, whichever is largest. For a 450 × 650 mm column with a 3 m clear height it is 650 mm at the top and at the bottom.
What is Mu,lim/bd² for M20 and Fe415?
2.76 N/mm². It is 0.36 × 0.48 × (1 − 0.42 × 0.48) × 20 = 2.759, the value printed in SP 16 Table D. For M25 it is 3.45 and for M30 4.14 with Fe415; with Fe500 the values are 2.66, 3.33 and 3.99. Above Mu,lim a rectangular beam needs compression steel.
Is this RCC design calculator free?
Yes. It runs in your browser, needs no sign-up and sends nothing anywhere. It is checked against the IITK-GSDMA ductile detailing examples and NPTEL's IIT Kharagpur RCC lessons, and the page will not build if the browser code and an independent Python check disagree on any of 2,732 numbers.
Related on Skill-Lync
- Seismic base shear calculator (IS 1893 storey forces for the same ETABS building)
- Shear wall design calculator (IS 13920 clause 10 walls and boundary elements of the same building)
- Isolated footing design calculator (IS 456, for the column's footing)
- Bar bending schedule calculator (cutting lengths and weight of these bars and links)
- Building load calculator (IS 875 loads on beams and columns)
- Structural design courses compared
- Student project: reinforcement detailing of beams from ETABS output
- All free engineering tools
Sources
- Bureau of Indian Standards, IS 456:2000 Plain and Reinforced Concrete: Code of Practice (with Amendments 1 and 2): clauses 25.1.2, 25.4, 26.2.1, 26.3.2, 26.5.1, 26.5.3, 38.1, 39.3, 40, Tables 19 and 20, Fig. 23, Annex G.
- Bureau of Indian Standards, IS 13920:2016 Ductile Design and Detailing of Reinforced Concrete Structures Subjected to Seismic Forces, with Amendment No. 1 (September 2017) and No. 2 (November 2020): clauses 6.1-6.3, 7.1, 7.3, 7.4, 7.6 (8 before Amendment 1).
- Bureau of Indian Standards, SP 16:1980 Design Aids for Reinforced Concrete to IS 456: Tables A, C, D and F.
- R. K. Ingle and S. K. Jain, Explanatory Examples for Ductile Detailing of RC Buildings, IITK-GSDMA-EQ22-V3.0, IIT Kanpur: Examples 1 and 3.
- NPTEL, IIT Kharagpur, Design of Reinforced Concrete Structures (course 105105104): Module 3 Lesson 5, Module 4 Lessons 8 and 9, Module 6 Lesson 14, Module 10 Lesson 22.
- Skill-Lync, the 342 beam and 335 column public reports of the ETABS detailing challenges, read 22 Nov 2026.