Bar bending schedule (BBS) calculator
Make the bar bending schedule of a beam, slab, column or footing: number of bars, cutting length of every bar and stirrup, laps, and steel weight by diameter. Lengths follow the bar's centre line round the real bend radius, next to the IS 2502 formula and the site rule. Free, no sign-up, exports to Excel (CSV).
IS 2502:1963 shapes · IS 1786 bar mass · IS 456 laps and tails · checked against SP 34's example schedule · Updated 20 Nov 2026
Beam (mm)
Bars
A leg of 0 makes a straight bar. Bars run the clear span plus both supports less the end cover; check their anchorage (IS 456 clause 26.2.3.3) on the drawing.
Slab panel (mm)
Main bars span Lx; cranks at 45°, height = thickness − 2 × cover − ⌀. Number of bars = clear length / spacing, rounded down, + 1.
Column (mm)
One lift: each bar is the storey height plus a compression lap, max(Ld,c, 24φ) per IS 456 26.2.5.1(d).
Footing (mm)
Mesh both ways; bent-up legs run to the top cover (D − 2 × cover).
One bar mark
Your stirrup (mm)
Outside size = member size − 2 × clear cover. Pre-filled with the common site formula 2(a + b) + 8d for a 230 × 450 beam with 25 mm cover. The bend radius comes from "Stirrup bend radius" below.
Bending
Bend radius is the inside radius. IS 2502 uses 2d for mild steel and 4d for IS 1786 (Fe415/Fe500) bars; stirrups are usually bent tighter. Hook tail 10d ≥ 75 mm is IS 13920, 6d the IS 456 minimum. "Next 25 mm" is IS 2502 clause 5.1.1.
| Bar mark | Shape (mm) | No. | Cut (mm) | Total (m) | kg |
|---|---|---|---|---|---|
| B1 ⌀16 Bottom bars | 3 | 4,725 | 14.18 | 22.4 | |
| B2 ⌀12 Top bars | 2 | 4,650 | 9.30 | 8.3 | |
| B3 ⌀8 Stirrups | 27 | 1,325 | 35.77 | 14.1 | |
| ⌀8 · 0.395 kg/m | 35.77 m | 14.1 | |||
| ⌀12 · 0.888 kg/m | 9.30 m | 8.3 | |||
| ⌀16 · 1.578 kg/m | 14.18 m | 22.4 | |||
- B1: exact 4716.2 mm · IS 2502 formula 4,714 · site rule 4,746 (+30)
- B2: exact 4639.6 mm · IS 2502 formula 4,638 · site rule 4,662 (+22)
- B3: exact 1316.5 mm · IS 2502 formula 1,288 · site rule 1,224 (-92)
My schedule
| Bar mark | No. | Cut (mm) | Total (m) | kg |
|---|
How to calculate the cutting length of a bar
A bar bending schedule lists every bar in a member with its mark, diameter, number, shape, bending dimensions and cutting length, then totals the steel by diameter. The bending dimensions on a drawing are usually outside dimensions. The cutting length is the length of the bar's centre line, which is shorter at every bend because the bar goes round a curve instead of the sharp corner the outside dimensions meet at. The difference per bend is the "bend deduction":
With r the inside bend radius and d the bar diameter. At r = 2d it is 2.07d, the source of the familiar "2d for a 90° bend". At r = 4d, the radius IS 2502 gives for bars to IS 1786 (cold-twisted bars in 1963; today's Fe415 and Fe500 bars carry the same standard number), it is 2.93d, so the 2d rule leaves a bent main bar about one diameter long per bend. Hooks add length instead: IS 2502 Table II gives a hook allowance H of 9d, 11d or 13d (and 5d to 6d for a bend B) depending on the steel. Then IS 2502 clause 5.1.1 rounds the cutting length up to the next whole 25 mm.
Weight follows from the area and 7,850 kg/m³:
So 8 mm weighs 0.395 kg/m, 10 mm 0.617, 12 mm 0.888, 16 mm 1.578, 20 mm 2.466 and 25 mm 3.853 kg/m. IS 1786:2008 Table 1 prints the same numbers rounded (0.395, 0.617, 0.888, 1.58, 2.47, 3.85).
Stirrup cutting length: the site formula leaves short hooks
The stirrup formula taught on most sites and in most BBS tutorials is "perimeter + two hooks of 10d − three 90° bends at 2d − two 135° bends at 3d":
Follow the bar's centre line round a closed stirrup with outside size a × b, centre-line bend radius rc, and a straight tail e after each 135° hook, and the exact length is:
Set the two equal and solve for e. That is the tail the site formula actually leaves: 5.3d at a tight bend (r = 0.5d), 4.2d at r = 2d and 2.8d at r = 4d. IS 456:2000 clause 26.2.2.4(b) asks for at least 6d after a 135° bend, and IS 13920:1993 for 10d and at least 75 mm. The formula never reaches either. The "−3d per 135° bend" is where the length goes: at the hook corner the bar wraps round 270° in all, and that curve needs length, not a deduction.
The beam above has 8 mm stirrups, 180 × 400 mm outside (230 × 450 mm with 25 mm cover). The site formula gives 1,224 mm, which bends into a stirrup with 34 mm tails at r = 2d, against the 80 mm that IS 13920 asks for. The exact length with 80 mm tails is 1316.5 mm, cut at 1,325 mm; with IS 456's 6d minimum tail it is 1252.5 mm. That is 101 mm more steel per stirrup, about 8% of the stirrup steel. If the bender makes full-length tails from the short bar anyway, the stirrup closes smaller, which squeezes the cover or the main bars instead.
IS 2502's own Table VIII formula, 2(A + E) + 24d with inside dimensions A and E, is consistent with the geometry: with r = 2d and the 8d tail of its clause 3.8 the exact centre line gives 23.56d, which the code rounds to 24d (Table VIII B, with 90° hooks: 19.63d, printed 20d). For this stirrup it gives 1,288 mm. Use "Check a stirrup" to test the cutting length in your own schedule.
Worked example: BBS of a beam
A 230 × 450 mm beam with a 4,000 mm clear span between 230 mm supports, 25 mm cover, 3 bars of 16 mm at the bottom bent up 200 mm at the ends, 2 bars of 12 mm at the top bent down 150 mm, and 8 mm stirrups at 150 mm starting 50 mm from each face. Main bars are bent at r = 4d, stirrups at r = 2d with IS 13920 tails.
- Bottom bars: run = 4,000 + 2 × (230 − 25) = 4,410 mm, two 90° bends: 4716.2 mm, cut 4,725 mm × 3 = 14.18 m = 22.4 kg.
- Top bars: 4639.6 mm, cut 4,650 mm × 2 = 9.30 m = 8.3 kg.
- Stirrups: (4,000 − 2 × 50)/150 + 1 = 27 nos, 1,325 mm each = 35.77 m = 14.1 kg.
- Total: 44.7 kg of steel. The site rule would order 43.8 kg.
Crank bars, laps and helixes
A slab bar cranked up over a support is longer than its horizontal run by the slope of the crank. For a crank height h (centre to centre of the bottom and top positions) at angle θ:
That is the "0.42D" rule. The four 45° bends of a double crank need a deduction of only 0.1d to 0.2d each, so the site habit of also subtracting 1d per 45° bend cuts each such bar about 3d short (31 mm on the 10 mm slab bar in the slab tab). Column bars are spliced as compression bars:
τbd is 1.2 N/mm² for M20 up to 1.9 for M40 (IS 456 26.2.1.1), increased 60% for deformed bars and 25% in compression. That gives 621 mm for a 16 mm Fe500 bar in M25. A helix (spiral) has n = height/pitch turns of length √((πDc)² + p²) each, with Dc the centre-line diameter.
How we checked the calculator
The independent Python script scripts/verify/bbs.py runs 55 checks, and this page recomputes all its examples with the browser code at build time and refuses to build if they differ.
- SP 34 Table 5.10. BIS's handbook on reinforcement detailing prints a typical schedule of 26 bar marks for two slabs, a beam and a column. Adding up its numbers and lengths gives its totals per diameter exactly (8 mm: 299.31 m, 118 kg; 20 mm: 47.42 m, 117 kg; 309 kg in all). Its weights per metre come from π/4 × d² × 7,850 (2.466 kg/m for 20 mm, not the rounded 2.47).
- IS 2502 Table II regenerated from its footnote rule (H = 9d/11d/13d/17d, B = 5d/5.5d/6d/7d, nearest 5 mm, at least 75 mm): all 126 printed values match except two. The 6 mm hook for cold-worked bars is printed 75 mm where 13 × 6 = 78 rounds to 80, and the 28 mm bend allowance for mild steel is printed 146 mm where 5 × 28 = 140. Both look like printing slips.
- The stirrup formula was checked by walking the bar's centre line segment by segment and arc by arc (four bar sizes and bend radii): the length matches the closed form and the outside box comes out at exactly a × b.
- IS 1786:2008 Table 1: every nominal mass from 4 to 40 mm matches π/4 × d² × 7,850 to its printed precision. IS 456 Ld: 47φ for Fe415 and 56.6φ for Fe500 in M20, the usual textbook values.
What this calculator does not cover
- Design. It schedules the bars you give it; it does not check that the steel is enough. The anchorage of beam bars at the supports, curtailment and the extra bars over supports come from the design and the drawing.
- Zoned stirrups and multiple lifts. Use "Any bar" for extra marks: closer stirrups at the ends of a beam, a column's next lift, chairs, extra top bars, or the second leg of a two-way slab.
- Couplers, welded laps and stock lengths. Bars longer than the 12 m stock length need laps that depend on where they are placed; add them as separate marks. Wastage (offcuts, re-bending) is a flat percentage on the total.
- Mass tolerances: IS 1786 allows ±7% on a batch of bars up to 10 mm, ±5% from 10 to 16 mm and ±3% above 16 mm, so the weighed steel can differ from the schedule.
Bar bending schedules are a challenge in Skill-Lync's building courses, next to RCC design to IS 456, AutoCAD and Revit detailing, and ETABS.
Frequently asked questions
How do you calculate the cutting length of a stirrup?
Take the outside dimensions a × b (member size minus twice the clear cover), add the two hook tails and allow for the bends. Exactly, along the centre line of the bar: L = 2(a + b) − 4d − 8rc + 3π·rc + 2e, where rc is the bend radius to the bar's centre line and e the straight tail after each 135° hook. For an 8 mm stirrup in a 230 × 450 mm beam with 25 mm cover, a 16 mm internal bend radius and 80 mm tails (IS 13920), that is 1316.5 mm, cut at 1,325 mm.
How do you calculate the weight of a steel bar per metre?
Multiply the bar's area by the density of steel, 7,850 kg/m³: w = d²/162.2 kg/m with d in mm (often rounded to d²/162). A 12 mm bar weighs 0.888 kg/m, a 16 mm bar 1.578 kg/m and a 20 mm bar 2.466 kg/m. IS 1786:2008 Table 1 lists the same values (0.888, 1.58, 2.47), and allows ±5% on a batch of 10 to 16 mm bars.
What is bend deduction in a bar bending schedule?
When a bar is dimensioned to its outside faces, the outside dimensions add up to more than the bar's real length, because the bar goes round the corner on a curve. The deduction is that difference. For a 90° bend it is 2(r + d) − (π/2)(r + d/2): 2.07d when the inside radius r is 2d, 2.93d when r is 4d. The site rule of 1d for 45°, 2d for 90°, 3d for 135° is a rounded version for r = 2d and outside dimensions.
What hook length should a stirrup have?
IS 456:2000 clause 26.2.2.4(b) asks for a straight tail of at least 6 bar diameters after a 135° bend (8d after 90°, 4d after 180°). In earthquake zones IS 13920:1993 asks for a 135° hook with a 10d extension, but not less than 75 mm. The tail is the straight part after the curve, so the cutting length has to cover the curve as well.
How do you calculate the number of stirrups in a beam?
Divide the length to be covered by the spacing, round down and add one. With the first stirrup 50 mm from each support face on a 4,000 mm clear span at 150 mm spacing: (4,000 − 2 × 50)/150 = 26, plus 1 = 27 stirrups. Where the drawing has closer spacing near the supports, count each zone separately.
How do you calculate the lap length in a column?
Column bars are lapped as compression bars: IS 456 clause 26.2.5.1(d) sets the lap equal to the development length in compression, but not less than 24φ. For a 16 mm Fe500 bar in M25, Ld = 0.87 × 500 × 16 / (4 × 1.4 × 1.6 × 1.25) = 621.4 mm, so the lap is 621 mm (about 39φ).
What is the 0.42D rule for a crank bar?
A crank of height h (centre to centre) at 45° makes the bar longer than its horizontal run by h/sin 45° − h/tan 45° = 0.414h, which sites round to 0.42h (the D in 0.42D is that crank height, not the slab depth). A slab bar cranked at both ends gets 2 × 0.414h. IS 2502 Table IV gives the same thing as C − √(C² − D²).
Is this BBS calculator free?
Yes. It runs in your browser, needs no sign-up and sends nothing anywhere. You can build a schedule for several members, see the steel weight per diameter, and download it as a CSV file for Excel.
Related on Skill-Lync
- Isolated footing design calculator (the steel the footing tab schedules)
- Concrete mix design calculator (IS 10262:2019)
- Steel structure load calculator
- Structural design courses compared
- All free engineering tools
Sources
- Bureau of Indian Standards, IS 2502:1963 Code of Practice for Bending and Fixing of Bars for Concrete Reinforcement: Fig. 1 and Table II (hooks and bends), Tables III to VIII (lengths of standard shapes), clauses 3.8 (stirrup tails) and 5.1.1 (cutting lengths to the next 25 mm).
- IS 1786:2008 High Strength Deformed Steel Bars and Wires for Concrete Reinforcement: Table 1 (nominal mass), Table 2 (mass tolerances), clause 7.2.1 (density).
- IS 456:2000 Plain and Reinforced Concrete: clauses 26.2.1 (development length), 26.2.2.4 (stirrup anchorage), 26.2.5.1 (laps).
- IS 13920:1993 Ductile Detailing of Reinforced Concrete Structures: 135° hooks with a 10d extension, not less than 75 mm.
- SP 34(S&T):1987 Handbook on Concrete Reinforcement and Detailing: Section 5 and Table 5.10 (typical bar bending schedule).