Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge

AIM: The Aim of this project is to create Class B surface and Class B surface by using Class A surface and to create a Closed body by using all these surface. draft analysis has to check weather it satisfy the manufacturing conditions or not. DRAFT ANGLE IN PLASTIC: Draft is the providing angle or tapers on product feature…

AIM: The aim of this project is to create electrical routing for the V-8 engine with having 16 cylinders. It is required to create a proper routing by using guiding channel, connectors used in near Cam shafts and near cylinders and finally to Flatten the required model. General procedure for Creating routing for the model:…

AIM: The aim of this project is to create electrical routing for the given electrical layout by using the connectors and to apply protective coverings with extrimity 30mm from the each and every connectors. the following connectors has used the electrical Layout: DT06-4S DT06-6S DT06-2S DT06-08SA Electrical Layout: Procedure…

AIM: the aim of this project is to create routing for the Tail Gate for the two tail lamps and also Number plate for lights. and also to create Flatten for the bundle segments. Steps involved to create routing: Download the Mechanical parts like connectors and suppourt devices and apply electrical properties Defining the…

AIM: The aim of this project is to arrange the arrange the electrical devices in the given manner and connect electrically with a proper bundle segment. and also flatten the complete model with protective covering device. Steps involved in this project: 1. Arrange the connectors as shown in figure: 2. Create a Bunle segment,…

AIM: The aim of this project is to design a core and cavity block for the the given Class A surface of Switch bezel by considering 2.5mm of thickness which already designed. CORE AND CAVITY BLOCKS: In a typical injection molding machine, one half of the mold (the A-side) is attached to the fixed side of the press, and…

HARNESS A ASSEMBLY OF HARNESS A   HARNESS B: ASSEMBLY OF HARNESS B: HARNESS ASSEMBLY CONTEXT: connect the HARNESS A AND HARNESS B:   ANNOTATIONS: BUNDLE CONTINUITY:    EXPANDED TREE OF HARNESS A AND B: GENERATING CAT PART:    

COIN HOLDER DESIGN:   AIM: The aim of this project is to create a Class B surface and Class C surface by using the given Class A surface and perform the draft analysis. DRAFT ANGLE IN PLASTIC: Draft is the providing angle or tapers on product feature such as walls, ribs, posts and bosses that lie parallel to the direction…

AIM: The aim of this project is to create a Class B surface and Class C surface by using the given Class A surface and perform the draft analysis. DRAFT ANGLE IN PLASTIC: Draft is the providing angle or tapers on product feature such as walls, ribs, posts and bosses that lie parallel to the direction of release from thmold…

AIM: The aim of this project is to create an electrical support for the given P clamp and to define electrical characterstics. Steps involved to define support: Download STEP/IGES fine of the P Clamp Create geometrical parameters like points and planes required for the electrical support. Define entry points and exit points…

AIM: The aim of this project is to create a Class B surface and Class C surface by using the given Class A surface and perform the draft analysis. DRAFT ANGLE IN PLASTIC: Draft is the providing angle or tapers on product feature such as walls, ribs, posts and bosses that lie parallel to the direction of release from thmold…

AIM: The aim of this project is to convert mechanical parts into electrical connectors by applying the electrical properties to the connectors. STEPS INVOLVED TO APPLY ELECTRICAL PROPERTIES: Create or download 3D CAD model of the connector. Create Geometrical parameters (points and axis systems) The reference points like…

DRAFT ANALYSIS OF FAN COVER DRAFT ANGLE IN PLASTIC: Draft is the providing angle or tapers on product feature such as walls, ribs, posts and bosses that lie parallel to the direction of release from thmold eases part ejection. for doing the draft analysis, a tooling direction is required.  DRAFT ANALYSIS TOOL IN PLASTICS:…

SECTION MODULUS: Section modulus is the geometric property of the given cross-section of any shaft or beam structures. It is the direct measure of the strength of the shaft section or the beam section. Higher the section modulus of a structure, the more the resistive it becomes bending. Higher section modulus, the more…

                                                              DESIGN OF BACKDOOR INTRODUCTION: The back door of a car is also called as tail gate. Back door is generally…

DESIGN OF ROOF: An automobile roof or car top is the portion of an automobile that sits above the passenger compartment of automotive vehicle which protects from sun, wind, rain and other external elements. Because the earliest automobiles were designed in this ear of horse drawn carriages, early automobile roofs used…

DESIGN OF FENDER Fender is an English US term for the part of an automobile (vehicle body) that frames on wheel (the fender outside). The primary purpose of the fender is to prevent sand, mud, rocks, liquids and other road spray from being thrown into the air by rotating the tyre. When the wheel is moving, tyres pick up…

HOOD: Hood is an opening body panel that covers the engine front engine in front engine vehicle. The hood is also another type of door in a vehicle as it of an outer panel and inner panel supported with hinges and striker when it was in closed condition. The inner panel provides strength while outer panel functions as…

UNDERBODY COATING: Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if you are getting the undercoating applied after a couple of years, it’s…

BENCHMARKING Benchmarking is a process of measuring the performance of a company’s products, services, or processes against those of another business considered to be the best in the industry, “best in class.” The point of benchmarking is to identify internal opportunities for improvement. By studying…

ADVANCE SHEET METAL DESIGN USING NX12.0- METAL BRACKET FROM 2D SKETCH INTRODUCTION: Brackets which are made of sheet metal is widely used in mounting device like antennas, automobile unit etc. OBJECTIVE: The objective of this project is to design a sheet metal bracket using nx12.0 sheet metal application workbench, And…

ADVANCE SHEET METAL DESIGN USING NX12.0- CREATE BRACKET INTRODUCTION: Brackets which are made of sheet metal is widely used in mounting device like antennas, automobile unit etc. OBJECTIVE: The objective of this project is to design a sheet metal bracket using nx12.0 sheet metal application workbench, And for drafting…

ADVANCE SHEET METAL DESIGN USING NX CAD- ODD SHAPED ENCLOSURE INTRODUCTION: Odd shaped enclosure structure plays an important role for protection of machine components which fitted along the structure or for the outer part of a machine. It is also used for safety purpose like heat, fluid flow, vibration etc. odd shaped…

ADVANCED SHEET METAL DESIGN USING NX 12.0- ASSEMBLY OF BOX INTRODUCTION: The sheet metal boxes are used for the purpose of providing safety and protective covering to various electrical and delicate electrical instruments, circuits and to store the tools in automobile sector. The project report contains detailed explanation…

ADVANCED SHEET METAL DESIGN USING NX CAD-CASING DESIGN INTRODUCTION: Casing is usually used as outer cover, a shell casing or tire casing, frame or frame work of a window or door, metal pipe or tube used as lining of water, oil, gas etc. The project report contains detailed explanation about designing of sheet metal and…

1.RADAR MAST FRONT VIEW OF RADAR MAST: SIDE VIEW OF RADAR MAST: TOP VIEW OF RADAR MAST: ISOMETRIC VIEW OF RADAR MAST: FEATURE TREE IMAGES OF RADAR MAST: 2. ASSEMBLY OF YACHT; FRONT VIEW OF YACHT: SIDE VIEW OF YACHT: BACK VIEW OF YACHT: TOP VIEW OF YACHT: ISOMETRIC VIEW OF YACHT: FEATURE TREE IMAGES OF YACHT: PROJECT REPORT…

DESIGN AND ASSEMBLY OF AMERICAN CHOPPER USING SOLID WORKS INTRODUCTION: The project report contains detailed explanation about designing of an American chopper and tools used to create American chopper which designed in SOLIDWORKS from each part modelling to final assembly. OBJECTIVE: The objective of this project is to…