Wiring harness calculator: bundle diameter, corrugated tube and bend radius

List the wires in a bundle. You get its diameter, drawn as a cross-section, plus the corrugated tube that fits, the bend radius, the weight per metre and whether each wire seals in a Deutsch DT connector. Free, no sign-up, runs in your browser.

The second tab does a whole harness: a trunk with branches to connectors. For every segment it gives the wire count, the bundle diameter and bend radius to type into CATIA V5, the length with slack and the tube. It opens on an example built from the Deutsch DT connectors of Skill-Lync's CATIA V5 wiring harness course. For fuse and wire sizing, use the fuse and wire size calculator.

ISO 6722 · SAE J1128 (Southwire) · Prysmian FLRY-B · Glenair bundle factors · Packomania · TE Deutsch DT · MIL-W-5088L · FAA AC 43.13-1B · 2,568 student reports read · Updated 22 Nov 2026

Counts of 0 are left out. ODs are each table's maximum (ISO 6722, Prysmian) or nominal (SAE J1128 from Southwire): real wires are usually a little thinner.

Bundle diameter6.9 mm8 wires · CATIA equal-area 5.9 mm
Tube15mm COTID 12 mm, 25% room
Bend radius9.7 mmCATIA 1.4 × Ø · 88 g/m

Each wire to scale at its outside diameter, one colour per size, in the tightest packing our solver finds (white circle). Dashed amber: Glenair's estimate when it is larger. Grey ring: tape.

  • Design diameter 6.9 mm: the larger of Glenair's factor 3.30 × the average wire 2.1 mm (6.9 mm) and the tightest packing we find (6.9 mm). A real bundle is never smaller than the packing.
  • CATIA V5's equal-area diameter √Σd² is 5.9 mm. To match the design diameter its area factor would need to be 1.37, not 1.
  • Course slit COT catalogue (week 3): 15mm COT (ID 12 mm) is the smallest with an inside diameter 25% over the 6.9 mm bundle.
  • Bend radius 1.4 × 6.9 = 9.7 mm in CATIA. The open aerospace rule (MIL-W-5088L 3.11.7, FAA AC 43.13-1B 11-117) asks for at least 21.0 mm: 10 × the largest wire (2.1 mm). CATIA's bend is tighter than that. No automotive bend rule is published openly.
  • 1 mm² FLRY-B thin wall (1.9-2.1 mm) is too thin for the standard DT size 16 seal (2.23-3.68 mm): it needs the reduced-diameter C015 'E-seal' (1.35-3.05 mm).

How to work out a wire bundle's diameter

A bundle's size comes from the wires' outside diameters, insulation included, not from their copper size. Round wires can't fill a circle, so a bundle is always bigger than one wire with the same total cross-section. There are three ways to put a number on it.

1. The equal-area diameter. One round wire with the same total area as all of them. It is always too small, and it is where CATIA V5 starts: IBM's 2006 note on CATIA V5R16 (APAR HD58324) says the segment's area is set equal to the sum of the wires' areas, multiplied by a factor of "1+" a setting. The value of that setting isn't in the note.

2. The tightest packing. The smallest circle the wires can be pushed into. For equal wires the best known answers are listed on Packomania (E. Specht). This tool finds a packing for any mix of sizes and draws it. For equal wires its result matches the best known packing for 2 to 8 wires and is never more than 2.5% above it up to 12. No real bundle is smaller than this.

3. Glenair's bundle factor. Glenair, a connector-accessory maker, publishes a table of factors by number of wires, used on the average wire diameter to size a backshell's cable entry. Up to 8 wires its factors are within 4% of the tightest packing (a little under it for 4, 5, 6 and 8). Past that they grow faster than the packing (20 wires: 5.6 against 5.12), which leaves room for a real bundle that is never perfectly packed:

Wires nTightest packing D/dGlenair f(n)Equal-area √nCATIA area factor k needed
22.0002.001.4142.00
32.1552.201.7321.61
42.4142.402.0001.46
63.0002.902.4491.50
73.0003.002.6461.29
83.3053.302.8281.37
103.8134.003.1621.60
124.0304.303.4641.54
194.8645.454.3591.56
205.1225.604.4721.57
306.1986.705.4771.50

Equal wires of diameter d. Tightest packing: Packomania's best known R/r. The last column is (larger of the two / equal-area)², the factor CATIA's area formula needs to reach the realistic diameter. It is never 1.

For a mix of sizes Glenair's average-wire factor can come out below the real packing (one 6 mm² battery feed with a few sensor wires is the example preset), so the tool takes the larger of the two. Tape adds its thickness t twice per layer m: a half-lap wrap (50% overlap) is two layers everywhere.

What the course reports assume

The week 4 and week 5-6 challenges of Skill-Lync's CATIA V5 wiring harness course ask the student to route a layout of Deutsch DT connectors and "make assumption for harness bundle diameters". We read all 1,517 public reports of those two weeks on 22 Nov 2026:

  • 265 state a bundle diameter at all. 10 mm is the most common (167 reports), then 15 mm (82), 5 mm (77) and 20 mm (32). 90 use 10 mm and nothing else.
  • 8 mention a wire size anywhere. The diameters are guessed, not worked out from the wires.
  • 81 set the CATIA bend radius ratio to 1.4 and 6 to 1.5. At least 38 set the slack to 0%.

A 10 mm bundle holds at most 16 thin-wall 1.0 mm² wires packed perfectly (14 by Glenair's factor), or 13 of 18 AWG GXL (11). The connectors in the challenge have 2 to 8 cavities. In the example layout, with one wire per cavity running back to the source, the trunk at the source needs 13.1 mm and the 2-way branch 4.7 mm. One diameter for every segment is wrong at both ends.

The week 3 routing challenge (860 reports) builds a slit corrugated tube catalogue (5, 10, 15, 20 and 35 mm COT) with a bend radius of 1.5 × the tube's outer diameter. Those sizes are the course's own: none of the maker tables we found has the same inside and outside diameters.

Wire outside diameters

Automotive wire comes in thick, thin and ultra-thin wall. The same copper size can differ by 30% in outside diameter, and that changes the bundle. The ISO values are each wall's maximum from the 2002 edition of ISO 6722 (the current ISO 6722-1:2011 table is not open). Prysmian's FLRY-B sheet gives the minimum and maximum, plus the mass.

Size (mm²)ISO thick, maxISO thin, maxISO ultra-thin, maxFLRY-B (Prysmian)FLRY-B kg/km
0.35–1.401.201.2-1.44.5
0.5–––1.4-1.66.6
0.752.501.901.601.7-1.99
12.702.101.751.9-2.111
1.53.002.402.102.2-2.416
23.302.802.402.5-2.820
2.53.603.002.702.7-326
44.403.80–3.4-3.742
65.004.30–4-4.361
AWGGXL OD (mm)TXL OD (mm)SXL OD (mm)
202.181.782.44
182.341.982.59
162.622.263.00
142.972.623.48
123.633.234.06
104.553.944.85

SAE J1128 cable as Southwire lists it (SPEC 50040, in inches; converted at 25.4 mm/in): nominal outside diameters, not the standard's maximums, which are not open.

Will the wire seal in a Deutsch DT connector?

The course's connectors are TE's Deutsch DT series: DT06-2S, -4S, -6S and -08SA with 2, 4, 6 and 8 cavities, all size 16 contacts. TE's DT catalogue gives size 16 a wire range of 14 to 20 AWG (2.0 to 0.5 mm²) and a standard seal range of 2.23 to 3.68 mm insulation outside diameter. The reduced-diameter C015 "E-seal" takes 1.35 to 3.05 mm. The often-quoted 1.35-3.05 mm is the E-seal (or size 20) range, not the standard size 16 one.

So thin-wall wire often doesn't seal in a standard DT: 1.0 mm² FLRY-B is 1.9 to 2.1 mm, below 2.23 mm. 18 AWG TXL (2.0 mm) is too thin as well, and 18 AWG GXL (2.3 mm) fits. The calculator checks every wire in the list when the connector is set to Deutsch DT.

Which corrugated tube fits

Pick the smallest tube whose inside diameter takes the bundle with room to spare. The only open sizing rule we found is from aviation: FAA AC 43.13-1B 11-249 suggests a conduit inside diameter "about 25 percent larger than the maximum diameter of the wire bundle". That is the default here; set the room to 0 to size tight.

HellermannTyton IWS (PA6)Inside Ø (mm)Outside Ø (mm)Min. bend radius (mm)Bundle up to, 25% room
IWS4.54.37.383.4
IWS7.56.710135.4
IWS8.58.411.7156.7
IWS109.913207.9
IWS1212.215.7309.8
IWS1312.715.83510.2
IWS1414.218.54011.4
IWS1716.621.24513.3
IWS1919.324.35015.4
IWS2221.325.45017.0
IWS2323.228.35518.6
IWS2625.831.26020.6
IWS292934.56523.2
Course slit COTInside Ø (mm)Outside Ø (mm)Bend radius 1.5 × OD (mm)Bundle up to, 25% room
5mm COT357.52.4
10mm COT71015.05.6
15mm COT121522.59.6
20mm COT172030.013.6
35mm COT323552.525.6

HellermannTyton automotive catalogue p. 232 (07/2019): the bend radius is for the listed (unslit) conduit; a slit version is made on request.

Bend radius: 1.4 × the bundle against the rules

In CATIA V5 a bundle segment's bend radius is its diameter times the bend radius ratio, so 1.4 lets a 6.9 mm bundle bend at 9.7 mm. The rules that are open are aerospace:

  • MIL-W-5088L 3.11.7 (1991, the predecessor of SAE AS50881): bundles at least 10 × the outside diameter of the largest wire, measured to the inside of the bend; a protected (covered) harness at least 6 × its own diameter and never under 10 × the largest wire.
  • FAA AC 43.13-1B 11-117: the same 10 × the largest wire, 6 × at breakouts or where wires reverse direction if they are supported. (Its paragraph 11-96 says 3 × there; the circular contradicts itself.)

For 2.1 mm wires that is 21.0 mm, more than twice the 1.4-ratio bend of the 8-wire bundle. With 18 AWG GXL the rule asks for 23.4 mm; the CATIA ratio only matches it on a bundle of about 16.7 mm or more. Car makers keep their own rules in internal standards, so treat the aerospace numbers as the cautious end, and the tube maker's minimum (HellermannTyton IWS10: 20 mm) as a hard limit for a covered segment.

Routing rules with numbers

Both open documents are for aircraft wiring; the automotive ones (SAE J1292, the car makers' own) are not open. They are still the best published starting point for clamp spacing and clearances:

RuleValueSource
Clamp or support spacing≤ 24 in (610 mm)FAA 11-96 a, 11-146; MIL-W-5088L 3.11.1 (42 in on rigid portions)
Sag between supports≤ ½ in (12.7 mm)FAA 11-118
Slack at a connector≥ 1 in (25.4 mm); two re-terminationsMIL-W-5088L 3.10.7.1; FAA 11-118
Fuel, oil, oxygen lines6 in, 2 in minimum, ½ in if positively clamped; wiring above the linesFAA 11-96 w, 11-126; MIL-W-5088L 3.11.11
Moving controls≥ ½ in under light hand pressureFAA 11-96 dd, 11-125
Edges, holes in structure⅜ in (9.5 mm), else a grommetFAA 11-115, 11-146 d; MIL-W-5088L 3.11.4
Bundle diameter in a clamp≤ 2 in (50.8 mm), design objectiveMIL-W-5088L 3.10.2
Hot parts (exhaust, heaters)separate; no distance givenFAA 11-96 z, 11-124; MIL-W-5088L 3.10.16
Across hingestwist, don't bendFAA 11-115; MIL-W-5088L 3.11.9

What this calculator does not cover

  • Car makers' own rules. Bend radii, clip pitch and clearances in OEM standards are not public; the aerospace values here are the open reference.
  • Wire sizing for current and voltage drop. That is the fuse and wire size calculator.
  • Shields and jackets. Glenair adds 0.025 in for an overall braid plus twice the jacket thickness; add them to the result yourself.
  • Wires that run between branch connectors. The layout tab assumes every wire goes back to the source. Real harnesses also link branches; add those wires to the segments they pass through.
Learn harness design

Turning a wire list into bundle sizes, tube choices and bend radii that survive the car is the day job of a harness design engineer. Skill-Lync's wiring harness course teaches it in CATIA V5, from defining connectors to routing, flattening and the drawing.

Frequently asked questions

How do you calculate the diameter of a wire bundle?

Add up the wires by their outside diameter, not their copper size. The quick estimate is Glenair's: the average wire diameter times a factor for the number of wires (3.3 for 8 wires, 5.6 for 20, 12.2 for 100). Check it against the tightest possible packing, which this tool draws: 8 thin-wall 1.0 mm² wires (2.1 mm each) pack into 6.9 mm, and Glenair gives 6.9 mm. For a mix of big and small wires the average-wire factor can come out below the packing, so use the larger of the two.

What bundle diameter should I assume in CATIA V5?

Work it out from the wires the segment carries. In the example layout on this page (one 18 AWG GXL wire per Deutsch DT cavity, every wire back to the source), the first trunk segment carries 20 wires and needs 13.1 mm, while the branch to the 2-way DT06-2S needs 4.7 mm. A single 10 mm for every segment, the value 167 of the 265 course reports that state a diameter use, is too thin for the trunk and more than twice the size of the small branches.

What is the bend radius ratio in CATIA V5 wiring harness?

It sets the bend radius of a bundle segment as a multiple of its diameter: with ratio 1.4, a 6.9 mm bundle may bend at 9.7 mm. 81 course reports use 1.4. The only open bend rules are aerospace: MIL-W-5088L and FAA AC 43.13-1B ask for at least 10 × the outside diameter of the largest wire, 21.0 mm for 2.1 mm wires. Automotive companies' own rules are not published.

What size corrugated tube do I need for my wire bundle?

The smallest one whose inside diameter takes the bundle with some room. FAA AC 43.13-1B 11-249 suggests an inside diameter about 25% larger than the bundle (aviation guidance; no automotive maker's figure was found). A 6.9 mm bundle then needs 8.7 mm: the course's 15mm COT (12 mm inside) or HellermannTyton IWS10 (9.9 mm inside) is the first that fits.

Which wire fits a Deutsch DT connector?

DT size 16 contacts take 14 to 20 AWG (0.5 to 2.0 mm²), and the standard seal needs wire insulation of 2.23 to 3.68 mm outside diameter (TE DT catalogue). Thin-wall automotive wire is often thinner: 1.0 mm² FLRY-B is 1.9 to 2.1 mm, so it needs the reduced-diameter C015 'E-seal' (1.35 to 3.05 mm). 18 AWG GXL (2.3 mm nominal) fits the standard seal.

How much does a wire bundle weigh?

Add the cable masses per metre. Prysmian lists FLRY-B 1.0 mm² at 11 kg/km, so 8 of them weigh 88 g per metre of bundle before tape, clips and connectors.

Related on Skill-Lync

Sources

  • ISO 6722:2002 (E), "Road vehicles - 60 V and 600 V single-core cables", Table 3 Dimensions (free preview, iTeh Standards). Superseded by ISO 6722-1:2011, whose table is not open.
  • Prysmian Kabel und Systeme, data sheets FLRY-B (DF 049-2000 Index V, 06.10.2020) and FLRY-A (DF 011-1998 Index S, 29.01.2021): outside diameter min/max and mass per km.
  • Southwire SPEC 50040, "Primary Automotive Lead Wire" (SAE J1128 GXL, TXL, SXL), rev. 1.000.057, Dec 2024, Table 1: nominal outside diameter and weight.
  • Glenair, "Wire Bundle Diameter Calculator": multiplication factors for 1 to 300 wires on the average wire diameter; braid and jacket allowance.
  • E. Specht, Packomania, "The best known packings of equal circles in a circle" (updated 25 Dec 2024): R/r for n = 1-30.
  • IBM Support, APAR HD58324 (CATIA V5R16, Oct 2006): bundle segment area = sum of wire areas × a factor "1+" a setting.
  • TE Connectivity, DT Family catalogue (2019, via Farnell): ordering table (cavities), wire sealing range by contact size; DT06-08SA product data sheet (size 16, insulation 2.23-3.68 mm).
  • HellermannTyton, automotive catalogue p. 232, "Corrugated Conduits IWS Polyamide 6" (07/2019): inside and outside diameters, minimum bending radius.
  • tesa SE, product pages tesa 51036 (260 µm) and tesa 51608 (280 µm).
  • MIL-W-5088L, "Wiring, Aerospace Vehicle" (10 May 1991; EverySpec): 3.10.2, 3.10.7.1, 3.10.16, 3.11.1, 3.11.4, 3.11.7, 3.11.9, 3.11.11.
  • FAA AC 43.13-1B with Change 1 (2001), chapter 11: 11-96, 11-115, 11-117, 11-118, 11-124 to 11-126, 11-146, 11-249.
  • Skill-Lync, 4,038 public reports of the CATIA V5 wiring harness course, 2,568 read on 22 Nov 2026 (all week 4, week 5-6 and routing reports): diameters, bend ratios, slack and wire sizes they state.
  • Skill-Lync, scripts/verify/harness.py: re-reads every table against the research notes, finds the tightest packings with its own optimiser (matching Packomania for 2-12 wires) and re-computes the bundles, tubes and the example layout; the page checks itself against it at build time.
Free counselling

From a guessed bundle to a harness that fits the car.

Harness teams hire engineers who can size a bundle from its wire list and explain every clip, tube and bend in the drawing. A Skill-Lync counsellor can map the course that fits the role you want.

Talk to a harness design course counsellor

Free. We call you back, usually the same day.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.