Wiring harness design in CATIA V5 - 3D modeling Week 2 Challenge

Q.1. What is Design Methodology? ANS. Design Methodology is sequence of steps which we have to follow while doing design. Above image is of design methodology and steps involve in it. Purchase Order:  We start designing after customer gives us purchase order. So, basically it is indication to start…

1. What is process of project execution activity? Answer: Project activities are those basically are being processed or being practiced in general project of BIW begins. Project activities are task from start to end of project. There are various step involved in project. Below fig. show flow chart of project activities.…

Q1 Ans BIW - Body In White BIW refers to the welded sheet metal components which form the structure of the vehicle to which the other components (like engine, chassis, exterior & interior trims) will be married or assembled. The stage in automotive design or automobile manufacturing in which the car body sheet metal…

1.QUICK RETURN MECHANISM Initailly each body create seperate file as per given dimension in drawing  like below mention image . body1 body2 body3 body4 body5 finally each body create to assembly with respective constraint. as per manufacture purpose create 2d drawing.   2.CV JOINT Initailly each body create seperate…

WIRING HARNESS ROUTING AND FLATTENING ON THE BACKDOOR OF A CAR Aim The project aims to route the wiring harness on the given backdoor of a car and prepare a flattened view drawing in the CATIA V5 by applying all packaging rules and following the industry standards and design guidelines. Introduction Wiring harness design…

   AIM: Route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. ENGINE WIRING HARNESS ROUTING:     fig.1. Given…

  AIM:         To flatten the wire harness assembly completed in week 4 assignment and place the flattened view on a drawing sheet. OBJECTIVE:         To flatten the wire harness assembly completed in week 4 assignment.         To orient the wire bundle as…

                                                 Wiring harness design in CATIA V5 - 3D modelling Week 5 & 6 Challenge Aim: Route two electrical harnesses per the given layout and interconnect…

Aim:  1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors:  DT06-4S DT06-6S DT06-2S DT06-08SA Connectors Layout Design: Steps to be followed: 1. Download…

   Wiring harness routing & packaging Rules Week 3 Challenge Q1. Download following clip cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Hellarmann Tyton – 21160129 process: Create two points one as entry and another as exit…

  Wiring harness design in CATIA V5 - 3D modeling Week 2 Challlenge AIM:  Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip. Deutsch DT06 –…

                                                         DOOR TRIM DEVELOPMENT  INPUTS: CLASS A surfaces of the DOOR ARM REST, MAP POCKET, BOTTLE HOLDER and LOWER…

                                                               A-PILLAR DESIGN WITH MASTER SECTION   AIM: To create the A Pillar Design with the master section…

 AIM: Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Create the Heat Stakes and the…

                                                Dog house design for the Door Trim   Aim: Create the Dog House for the Door Trim considering the design rules and perform the draft analysis for…

                                                                                 Attachment Feature Creation (Ribs…

AIM : To create the Bumper Design Plastic component through the given Class-A surface.  Objective To create a tooling direction. To perform draft analysis for given A-Surface and prepare the final close body. To design the Bumper plastic component by creating the B-Surface and C-Surface using the given Class-A…

DESIGN AND DRAFT ANALYSIS OF SWITCH BEZEL OBJECTIVE The objective of the project is to design the switch bezel and to do a draft analysis for it by creating the required tooling direction with the help of Bisecting method. INTRODUCTION The control panel bezel is the frame part of the window switch that holds its switch…

AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. REPORT ON DRAFT ANALYSIS: Given Class A Surface: STEP…

                                                                        BACK DOOR DESIGN OBJECTIVE To design the back door of a Car To design…

                                                           Butterfly Valve Assembly Aim:    To Assemble and apply GD&T to the butterfly valve assembly drawing.…

                                                                                          …

                                                             FENDER…

  Objective: Performing Wheel arch calculation with an European Standards and prove whether the car is passed for standard or not. Introduction Wheel Arch:                 The wheel arch is an arch-shaped cavity in the body of a vehicle, which houses a wheel. It has two…

                                                                      HOOD DESIGN   AIM: To Design Hood outer panel, inner panel and the necessary reinforcements by following the Master section mentioned with the design parameter explained in the videos. Submit an assembly of Hood inner panel, outer panel, latch, hinge,…

                                                              SECTION MODULUS OF A HOOD      Aim:      To calculate section modulus of…

                                                                    UNDERBODY COATING   AIM:  To make a detailed report explaining about under-body…