Wiring harness design in CATIA V5 - 3D modeling Week 2 Challenge

                                                                                           …

                                                                      Project 01(WIRING HARNESS FOR ENGINE)   AIM:- To route the wiring…

                                                  Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge AIM:- To flatten the wire harness assembly completed in week 4 assignment and…

                                              Wiring harness design in CATIA V5 - 3D modeling Week 5 & 6 Challenge AIM:-  Route two electrical harnesses as per the given layout and interconnect…

                                               Wiring harness design in CATIA V5 - 3D modeling Week 4 Challenge AIM:- Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering on all branches connected…

                                                        Wiring harness routing & packaging Rules Week 3 Challenge AIM:- To solve the above assignment questions and define…

                                                      Wiring harness design in CATIA V5 - 3D modeling Week 2 Challenge AIM:-  Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors…

                                                                                        Design…

                                                                                           …

                                                                                       Fender Design…

                                                              Section Modulus calculation and optimization AIM:-Use the section from your Hood design and calculate the section modulus using the formula S= I/y.   Section Modulus:-The section modulus (S) is geometry property of the cross section used for designing beams…

                                                                                  Hood design-Week 2   AIM:-  To…

                                                                           Fender Design - Wheel Arch Challenge AIM:- Calculate the Wheel Arch gap at required points and check whether the car passes the European standard.                                                FENDER:- Fender is the US English term for the part…

                                                                                        Underbody Coating AIM:- Write a one-pager about Under-Body Coating and its purpose, its types in detail, and its pros and cons. UNDERBODY COATING:- Underbody coating is usually a dense cladding (often based on rubber) applied uniformly…

                                                                                       Benchmarking…

                                                                                     Week 11 - Final project…

                                                     Week 10- Assembly Workbench AIM:-   To create a 3 D Solid CAT Part files using 2 D Sketch, also to solve the sketches with fully (ISO) constrained and also to create a 2 D Drafting sheet from the solid CAT part and Assembly Product with the Frame and Tittle Block. OBJECTIVE:- …

                                                               Week 9 - Project - A pillar Design with Master Section AIM:- The main objective of this challenge is to understand the given master section to create a solid body and B-side features for a given class A surface, by considering all the design parameters. FIRST…

                                             Week 9 - Project 1 - Door Trim Lower with Engineering Features AIM:- Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and…

                                                                    Week 9 - Attachment Feature Creation - Challenge 2 AIM:- Create the Dog House for the Door Trim considering the design rules mentioned in the video. Consider the thickness of the part to be 2.5 mm. "C" is where the doghouse contacts the backside of the…

                                                                   Week 8 - Challenge 6 - Core & Cavity Design AIM:- Create the Core and cavity blocks for the switch bezel designed in the earlier challenge.  FIRST DRAFT ANALYSIS OF SOLID BODY:- CORE AND CAVITY DESIGN:- CORE DESIGN:- First, I have taken the boundary of…

                                                                  Week 8 - Challenge 5 - Door Trim Lower AIM:-   Create the Door Trim Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the…

                                                                           Week 8 - Challenge 4 - Bumper AIM:-  Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end…

                                                                       Week 8 - Challenge 3 - Coin Holder Design AIM:-  Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle…

                                              Week 9 - Attachment Feature Creation (Ribs & Screw Boss) - Challenge 1 AIM:- Create the rib for the Drill Handle considering the design rules. CLASS…

                                                                  Week 8 - Challenge 2 - Switch Bezel Design   Objective  The objective…

                                               Week 8 - Challenge 1 - Base Bracket Design OBJECTIVE To create base bracket plastic component from the given class- A surface. To create the tooling axis…

                                            PARSING NASA THERMODYNAMIC DATA AIM:- Write a function that extracts the 14 coefficients and calculates the enthalpy, entropy and specific heats for all the species…

                                                                                          …

                                                                                                                           …

                                                                                                …

                                                                     BAJA ALL TERRAIN VEHICLE AIM:- To prepare a technical report on simulation of…

                                                           WASHING MACHINE STATEFLOW CHART   When current and water supply on all lamp shows green In this model we use…

                                                                 DOORBELL USING SOLENOID               To make this Simulink…