Underbody Coating

Final Independent Project   Title The Basis of Cylinder Engines with Pistons: A Comprehensive Report   Abstract Cylinder engines with pistons represent a cornerstone of internal combustion engine technology, powering various vehicles, machinery, and equipment across the globe. This report delves into the fundamental…

Aim: To perform MBD Simulation on IC Engine Valve Train.   Objective: Model the parts and assemble them in SolidWorks.  Run the simulation using the below parameters Sl. No CAM Lift (mm) Speed (RPM) Material  1 3.5 1500 Cast Carbon Steel 2 6 1500 Cast Carbon Steel   Obtain the Plot of the following:…

Exercise: Model all the parts and then assemble them in SolidWorks. The motion analysis is going to be carried out in three different conditions, Sl.No Wrist Pin Offset ` Crank Speed (Rpm) 1 "0" mm 2000 2 10 mm Positive  2000 3 10 mm Negative  2000   Wrist Pin Offset - The position of the wrist pin…

Topic: Planetary Gear Introduction: Planetary Gear An epicyclic gear train (also known as planetary gear) consists of two gears mounted so that the centre of one gear revolves around the centre of the other. A carrier connects the centres of the two gears and rotates to carry one gear, called the planet gear, around the…

AIM : Design the Internal Geneva Mechanism   OBJECTIVE : Create 3D models for driver and driven wheels. Perform motion analysis by rotating the driver wheel at 10rpm for 1st study and 20 rpm for another study. Obtain the Results for Contact force (between driving and the driven wheel) as a function of time, angular…

Centrifugal Pump Design and Analysis   Performance diagram. Obtain the relationship between Pressure ratio and mass flow rate and explain your results. Pressure ratio = Outlet total pressure/ Inlet total pressure   SOLUTION: INTRODUCTION  SolidWorks Flow Simulation is a powerful computational fluid dynamics (CFD) software…

Solution: AIM: Modelling and simulation of flow through a flowbench PROJECT: For this project, you will create a 3D model of a flow bench and run flow analysis. You will be obtaining a plot of lift vs mass flow rate You need to do the following Grid dependence test For three grids run your simulation at a particular valve…

Solution: AIM NACA Airfoil simulation INTRODUCTION  SolidWorks Flow Simulation is a powerful computational fluid dynamics (CFD) software that is used to simulate and analyze fluid flow and heat transfer in various engineering applications. It is a comprehensive tool that is seamlessly integrated into the SolidWorks…

Flow over a cylinder Simulate the flow over a cylinder for the conditions shown in the video. Calculate the baseline case Reynolds number.  Re = rho*U_inlet*D/mu D = cylinder diameter mu = dynamic viscosity rho = density Run a baseline simulation and then calculate the Reynolds number. Then increase the Reynolds number…

ABSTRACT Walking Bike is a totally new way of moving. With the electric assist it takes no more effort to walk than “a walk in the park”. The electric assist in combination with the gear is boosting your walking pace up to the speed of the regular bike. In this bicycle the frame of the bicycle is completely…

Independent Research Project  FEA ANALYSIS USING SOLIDWORKS FEA is among the most powerful and commonly used features in CAD design. It is integral to CAD for analyzing an object through the use of finite elements that include small rectangular and triangular shapes. SOLIDWORKS Simulation is a Finite Element Analysis…

Challenge 2- Comparing the performance of three types of beams under bending load  AIM Comparing the performance of three types of beams under bending load in Solidworks INTRODUCTION  inite element analysis (FEA) is the use of calculations, models and simulations to predict and understand how an object…

ASTON MARTIN ONE-77 OBJECTIVE To set up the blueprints for Aston Martin ONE-77 To model the individual parts of the Aston Martin ONE-77 using SolidWorks. To assemble all the parts with proper mates. To give proper appearances and decals for the parts. To position the assembly and set up cameras, lights and environments.…

Boeing-747 _ Final_Project of Boeing OBJECTIVE: To set up the blueprints for Boeing 747-8. To model the individual parts of the Boeing 747-8 using SolidWorks. To assemble all the parts with proper mates. To give proper appearances and decals for the parts. To position the assembly and set up cameras, lights and environments.…

      Design, Assembly and Rendering of a ELECTRIC CHAMBER using SolidWorks and SolidWorks Visualise   OBJECTIVE  Design the parts of the ELECTRIC CHAMBER Assemble the parts in solidworks assembly. Render a high quality image using photoview 360 and SolidWorks Visualise. INTRODUCTION SOLIDWORKS 2022 PREMIUM EDITION  SolidWorks is…

Model Radar mast and Assemble the Yacht using SolidWorks  Solution: 1.Radar mast                                                                …

                                                                          MODELING AND RENDERING OF AMERICAN CHOPPER     OBJECTIVE …

INTRODUCTIONUNDERBODY COATING                           Underbody coatings are those which are used to prevent car bodies against rust & corrosion. This underbody coating helps in protection from dust and moisture also some other factors such as…

BENCH-MARKING Benchmarking is the structured comparison between similar products,services or process on some dimensions of performance. Automotive Benchmarking can be simply defined as a process of analysing similar products based on selection factors.   CASE 1 Mr. D.S. Pughazhyendhii is a married man who lives…