Structural analysis of a buidling using Robot Structural Analysis

Develop general arrangement for the RC office building. Analyze and design the building as per IS standard code in TEKLA STRUCTURAL DESIGNER. Refer the attached plan and elevation. The building to be designed for dead, live, wind and seismic loading. AIM : To develop general arrangement for the RC office building…

1. Generate a report for the steel building design from challenges 1 – 6 along with the loading summary AIM : To generate report for the steel building design from challenge 1-6 TOOLS REQUIRE : Report, model report, show report PROCEDURE : Open the structure and analyze it Now click on report tab Now select model…

AIM : To Analyze and Design a Boiler shed structure as per IS code in Tekla Structural Designer TOOLS REQUIRE : Construction levels, model tool, grid lines, file, manage property set, columns, beams, frames, loads, load cases, wall panels, roof panels, bracings, analyse, validate, etc. PROCEDURE :  Firstly open tekla…

1. Design the slab and foundation of the model. Outline the thought process for designing of the elements (column, beam, slab and foundations) AIM : To design the slab and foundation of the model and to Outline the thought process for designing of the elements TOOLS REQUIRE : Slab, foundations, check panel, catalogue,…

1. Based on the analysis design RC column and beam AIM : To design RC column and beam based on the analysis TOOLS REQUIRE : Beams, columns, interactive design, static, validate, design, settings, property browser, etc. PROCEDURE :  Firstly open the previous project file Now select a particular column and right click then…

1. Generate seismic loading based IS codal provisions and zone II. Any other data you can assume and input              accordingly AIM : To generate seismic loading based IS codal provisions and zone II. Any other data you can assume and                    input accordingly TOOLS REQUIRE : File, open, project browser,…

1. Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab thickness as per the design Brick wall load Roofing load AIM : To calculate dead load in design report based on IS code and apply dead load on the model TOOLS REQUIRE : Manage properties, slabs, properties…

1. Setup model for RC building design and based on following parameters for cover             MEMBERS        IN CONTACT WITH                    GROUND          ABOVE GROUND      …

AIM : To analyse and design a steel building to 10T CRANE as per IS standard code in Tekla Structural Designer            and to design a structure according to the attachments provided TOOLS REQUIRE : Grids, manage property sets, construction levels, model, columns, beams, slabs, braces,…

1. Summarize your study for the bending moment, shear force and deflection diagrams for the elements of the            model Bending Moment : Bending moment (BM) is a measure of the bending effect that can occur when an external force (or moment) is applied to a structural element. This concept is important in structural…

1. Generate manual wind loading in the design report based IS code as per the following input Basic wind speed = 39m/s Terrain category 2 AIM : To generate manual wind loading in the design report based IS code as per the following input TOOLS REQUIRE : IS Code Book, Calculator, Excel  PROCEDURE :  Firstly we…

1. Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab as per design Brickwall 150mm thickness Roofing load based on purlin size Ceiling loading 0f 0.3KN per sq m AIM : To calculate dead load in design report based on IS code and apply dead load on the model…

1) AIM : To open architectural template and set the project base point and project shared coordinated for the project.     TOOLS REQUIRE : Architecture tool, grid tool, manage tool, file, save as, project file        PROCEDURE :  Firstly select the architectural template…

A)  AIM: To use the architecture/structural project file developed from week 6-8, Export the Revit file to Navisworks cache file. TOOLS/COMMANDS USED : Architectural file. file. Open Export. NWC. Navisworks. View.  3D view.  PROCEDURE : 1.the Revit file which is to be exported to the Navisworks file…

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. AIM: To create a seet of sinusoidal points and create a curve and create a surface. out of the curve TOOLS USED : • Dynamo • Code block • Range • Math.sin. • Integer slider • Product…

1)    Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below           a. Using 3D model create a section box           b. To create similar doors and windows in a floor plan layout     …

1)   What are HVAC systems ? Why are they essential in modeling of buildings? A) HVAC system is one of the major component in the modeling of a building. The term HVAC stands for Heating, Ventilation and Air conditioning, here  Heating means to increase the temperature of the input air which flows…

1)  Select the type of structure you want to build from one of the three below        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School A)  From the given options, the type of structure I want to build is a Multi-unit…

AIM : To Create a G+4 Residential building as per NBC standards and make it a central model file. And model should contain : The sloped roof at the top level of the building (10 degrees) Architectural components including furniture and home appliances Room tags and Annotations Section cut through each room either longitudinally…

3Q) Aim : To create a rectangular layout of walls of about 40’0” x 35’0”. Tool Required : Architecture, Wall Procedure : Firstly to create walls in Revit, we need to select “Architecture” tool from the tool bar layout, and then we should select wall tool which is located in “build”…

1Q)  BIM is defined as “ Building Information and Modeling “. It is 3D model based software, which helps us to plan, design,manage building construction and visualize very efficiently by using wide variety of tools. BIM contains wide range of materials data when compared with CAD. Some best features of…

1Q) AIM : To create floor for the previously done project and to align the floor plan with grids.       TOOLS REQUIRE : file, open, architecture tool, floor tool, grids        PROCEDURE :  Firstly after opening revit software select file tool and open the previous…

1Q) Why are building codes or standards essential for the modeling/ efficiency of drawings in Revit ? The National Building Code of India (NBC), a comprehensive building Code, is a national instrument providing guidelines for regulating the building construction activities across the country. It serves as a Model…

  1Q) AIM : To create ceiling from architecture tab above the walls at first floor level.        TOOLS REQUIRE : Architecture tab, ceiling tool, file, offset        PROCEDURE : Firsty select file option and open the required revit file. Now select first floor from project browser…