Section Modulus calculation and optimization

AIM: To Design the outer upper and lower panel, inner panel with the necessary reinforcements by following the Master section with the design parameter for the given class A surface.  INTRODUCTION: A door is a hinged part which is used for entry and exit of the vehicles. Back doors are one of the type doors of the vehicle…

AIM: To design a roof with all the components like front roof rail, rear roof rail, and bow roofs by following the given master sections and the high-quality surface, considering all the design requirements as per the OEM standards. ROOF  An automobile roof or car top is the portion of an automobile that sits…

OBJECTIVE : The main objective of this project is to design a fender using  a new age design software - NX - CAD INTRODUCTION : Design of any product starts from an requirement . The design engineer sketches the product based on the the requirement . Then the 2D sketch  with the proper dimensions is converted…

AIM: To design a roof with all the components like front roof rail, rear roof rail, and bow roofs by following the given master sections and the high-quality surface, considering all the design requirements as per the OEM standards. ROOF  An automobile roof or car top is the portion of an automobile that sits above the…

Aim  To calculate the section modulus of the previously designed hood for analyzing its strength and also optimizing the design to see the difference in the bending strength of the hood. Higher the section modulus of a structure, the more the resistive it becomes to bending. Section modulus Section modulus is a geometric…

HOOD DESIGN using NX     INTRODUCTION - In this report we are going to study about Hood Outer Panel, Hood Inner Panel, Hinges , Striker in NX-12. Using the CAD we are going to design and develop the model with in safety conisderation. Hood -  The hood or bonnet is an opening body panel that covers the engine in a front-engine…

Aim:      This project shows that examine the given fender wheel arch design to verify if the wheel arch of the fender meets the European standards. FENDER: Fender is the part of a car that protects and frames its wheels and keeps mud from splashing it. Most modern vehicles have fenders on their front wheels. It is the…

INTRODUCTION A car’s underbody is exposed to the most wear and tear caused by muddy water, potholed roads, stones and other obstacles on the road.Because it’s not in plain sight, we often do not see the damage. In Indian road conditions, a car’s underbody is most prone to corrosion. Underbody coating provides long term…

BENCHMARKING :- Benchmarking is a process of measuring the performance of a company’s products, services, or processes against those of another businessconsidered to be the best in the industry, “best in class.” The point of benchmarking is to identify internal opportunities for improvement. Bystudying companies with superior…

AIM To create a door interior part from the inputs of class A surface along with master section by following the design rules followed in tier 1 and OEM industries in catia v5   SOFTWARE USED CATIA V5   OBJECTIVES Create a sketch by using Positioned sketch All the should be sketches should be Iso-Constrained…

QUICK RETURN MECHANISM  SLOTTED LEVER BASE RECTANGULAR SLIDER CONNECTING ROD CIRCULAR SLIDER ASSEMBLY         CV JOINT   JURNAL CENTRAL YOKE SIDE YOKE ASSEMBLY      

Aim : The objective of this project is to develop a Closed Surface Model using Master Sections To develop attachment features for Fixation of Parts by following OEM Design standards and procedures in CATIA SURFACE WORKBENCHand PART DESIGN   Description : Master Section :Master Sections are the guides for design requirements…

AIM:To create Plastic design and attach the Engineering features and generate the Draft Analysis for the given Door Applique Class A model. DOOR APPLIQUE   DOOR ATTACHMENT SURFACE   PROCEDURE:1.Check for any openings in the given model Door Applique by using BOUNDARY. In BOUNDARY > select edges - select the…

SCREW BOSS AND DOG HOUSE DESIGN ON COIN HOLDER AIM- Create the screw boss and dog house for the centre console coin holder considering the design rules mentioned in the video. General Rules for Screw bosses. Draft of 0.5 degree on walls of boss Thickness is 40% of the nominal wall at the base. Height to diameter ration-3:1…

Aim:- To create an out featured rib on the centre console coin holder.   Procedure:- Firstly open the coin holder using the open command   Rib:- To create a rib first extract the base surface of the coin holder. Create a positioning sketch draw a line , constraint it and define it as an output feature. Extrude the output…

AIM : Create the Core and cavity blocks for the switch bezel designed in the earlier challenge. TOOLING AXIS: IT IS THE AXIS IN WHICH THE DIRECTION CORE AND CAVITY OPEN. THIS IS THE VERY IMPORTANT FOR PRODUCTION OF PLASTIC COMPONENT. MOST OF THEDEFECT WILL DONE IMPROPER TOOLING AXIS CREATION BY THE PLASTI DESIGNER. THERE…

AIM: To make a model from the provided class-A surface. INTRODUCTION:CLASS-A SURFACE: A surface made by the designer which is given as an input to the plastic modeler to work on. It is aesthetic surface and the outer most surface. CLASS-B SURFACE: A surface below a certain thickness from the class-A surface is class-B…

AIM: To design arm rest model from the provided class-A surface. THEORY: CLASS-A SURFACE: A surface made by the designer which is given as an input to the plastic modeler to work on. It is aesthetic surface and the outer most surface. CLASS-B SURFACE: A surface below a certain thickness from the class-A surface is class-B…

AIM :-To Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Firstly, the connectivity of the given Class-A surface…

AIM :To Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meetingthe requirements of the draft angle and at the end perform the Draft analysis on the model. INTRODUCTION Draft angle and Why it is needed?Draft is an…

DRAFT ANALYSIS ON A FAN COVER: Objective: Main objective is to perform draft analysis to check if the part has the given draft on its all faces. And to determine the tooling axis. Draft: It is a tool used in CATIA to make the faces taper with respect to tooling axis. Tooling axis is the direction of mold part ejection.…

 1. Radar Mast    FRONT VIEW :-     SIDE VIEW :-     ISOMETRIC VIEW :-   FEATURE MANAGER TREE :-        2. Yacht Assembly      AIM & OBJECTIVE : The objective is to design and assemble varioius parts using the solidworks.   Yacht:  …

MODELING AND RENDERING OF AMERICAN CHOPPER USING SOLIDWORKS Introduction: Solidworks is one of the prominent modelling software available. This software is mainly used to model 3D parts using 2D sketch. It also has the option to specify the material and look for the model which we create. It has other Add-in features like…

AIM: Create a Rankine Cycle Simulator using MATLAB. OBJECTIVE:  Calculate each state points of the Rankine Cycle (any type of your choice) based on user inputs.  Plot the corresponding T-s and h-s plots for the given set of inputs. Calculate Efficiency. THEORY: The Rankine cycle is an idealized thermodynamic cycle of a…

AIM:-  To parse the NASA thermodynamic data file and then to evaluate thermodynamic properties such as Cp, H, and S of various gas species through MATLAB  OBJECTIVE:- Writing a function that extracts the 14 co-efficient and calculation of the enthalpy, entropy, and specific heats for all the species in the data file. Calculation…

AIM:- To write a code in MATLAB to optimise the stalagmite function and find the global maxima of the function an plot the graphs. OBJECTIVE:- To study about the optimization process and to find out the optimum value. Study th statistical behaviour of unbounded, bounded and increase the no of iterations to find the global…

 Aim :-  To write a program that solves the following ODE. This ODE represents the equation of motion of a simple pendulum with damping.ORDINARY DIFFERENTIAL EQUATION (ODE) :-An ordinary differential equation (also abbreviated as ODE), in Mathematics, is an equation which consists of one or more functions…