Project 2

TO DESIGN A RIB AND SCREW BOSS OF A DOOR HANDLE BY USING CLASS A SURFACE AIM: To design a door handle Plastic component through the given Class-A surface by creating a tooling axis and draft analysis of the given surface and also design a rib and screw boss. DESIGN PROCEDURE: To setup the class-A surface and to creating…

CORE AND CAVITY OF A SWITCH BEZEL  AIM:  The aim is to design the core and cavity of a switch bezel from the solid component of a switch bezel  Earlier switch bezel can be design by using a CLASS A SURFACE and creating B SURFACE and C SURFACE to create a surface and solid component from it.  DESIGN PROCEDURE:  To setup…

TO DESIGN A CAR BUMPER BY USING CLASS A SURFACE  AIM:  To design a car bumper Plastic component through the given Class-A surface by creating a tooling axis and draft analysis of the given surface.   DESIGN PROCEDURE:  To setup the class-A surface and to creating a tooling axis   add draft angle   To create a base surface…

TO DESIGN A COIN HOLDER BY USING CLASS A SURFACE  AIM:  To design a coin holder Plastic component through the given Class-A surface by creating a tooling axis and draft analysis of the given surface.   DESIGN PROCEDURE:  To setup the class-A surface and to creating a tooling axis   add draft angle   To create a base surface…

DESIGN A SWITCH BEZEL BY USING CLASS A SURFACE  AIM:  To design a switch bezel Plastic component through the given Class-A surface by creating a tooling axis and draft analysis of the given surface.   DESIGN PROCEDURE:  To setup the class-A surface and to creating a tooling axis   add draft angle   To create a base surface…

  BASE BRACKET DESIGN BY USING CLASS A SURFACE  AIM:  To design a Base Bracket Plastic component through the given Class-A surface by creating a tooling axis and draft analysis of the given surface.   DESIGN PROCEDURE:  To setup the class-A surface and to creating a tooling axis   add draft angle   To create a base surface…

OBJECTIVE: The main objective of this project is to understand the fundamentals of GD&T and apply them to the design of a butterfly valve using Siemens NX. INTRODUCTION: GD&T stands for Geometric Dimensioning and Tolerancing. It is a standardized way of communicating information about a product and it is applied…

                                                                            DESIGN OF BACKDOOR   AIM:- To design the Back door as per the given skin requirements and also provide reinforcements for hinges, Latch, Gas stay, and wiper motor mounting areas. INTRODUCTION:- The back door of the car is one of the closure commodities…

                                                 CAR ROOF DESIGN ANS ANALYSIS OF REINFORCEMENTS   INTRODUCTION:- An automobile roof is a portion of an automobile that sits above the passenger…

                                                                 AUTOMOTIVE FRONT FENDER DESIGN      AIM:- To Design Drip Area, Sill Mount Area,…

                                                                            FENDER DESIGN -  WHEEL ARCH   AIM:- To…

                                                          SECTION MODULUS CALCULATION AND OPTIMIZATION   Section Modulus:-              …

                                                                                                                                               HOOD DESIGN   AIM:- In this project, a Hood Assembly will be designed which would be consists of a hood outer panel, hood inner panel. The latch for the hood will also be placed…

                                                                             Underbody Coating    Under body coating…

                                                                               BENCHMARKING Benchmarking in Automotive Industry…

                                                                                                                             WIRING HARNESS FOR ENGINE                                                                                                                                             PROJECT-1   Aim- To route the…

                                                                                           …

                                                                            WIRING HARNESS FLATTENING  Switching To The Electrical…

                                               Creating the Wire Harness Geometrical Bundle Harness Bundle creation for given Harness Layout(Harness_A):-  Follow below steps to create geometrical…

                                                             Preparation Of Harness Assembly                 As we are done with…

WHAT ARE THE IMPORTANT PARAMETERS REQURIED TO BE DEFINE A"P CLAMP" AS A ELECTRICAL SUPPORT. Clip Defination:- This another important component of the wiring harness which should be define wiring harness routing following important parameters requried to define. Entry Point & Plane Exit Plane Base Plane Clip has two…

                                                   Wiring harness design in CATIA V5 - 3D modeling First we can open te.com site download the Deutsch DT06 – 08SA and open in CATIA…