Project 2

                                                                DESIGN OF BACKDOOR AIM: To Use the provided styling surface to come up with a back door design,…

  OBJECTIVE: The objective of this project is to design a butterfly valve and apply GD&T to it's components and final assembly using Siemens NX.   PROCESS PLAN:   Description of Butterfly valve:   A butterfly valve is a valve that isolates or regulates the flow of a fluid. The closing mechanism…

CAR BACK DOOR WIRING HARNESS DESIGN- PROJECT 2 AIM: To route the Wiring harness on given car body back door and prepare flatten view drawing in CATIA V5.   INTRODUCTION: A wire harness, also commonly referred to as a wiring harness, is an exterior sheath used to cover some types of electronic wires. Generally, wiring…

WIRING HARNESS DESIGN PROJECT 1 AIM Design and develop the Wiring harness on Given V6 Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design.   INTRODUCTION A wire harness, also commonly referred to as…

Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge AIM To prepare the flattened view of wiring harness assembly using the Electrical harness Flattening workbench and place it on the drawing sheet. INTRODUCTION Once a product is ready to manufacture, its design must be precise or it risks costly errors and…

Wiring harness design in CATIA V5 - 3D modelling Week 5 & 6 Challenge AIM Create two electrical harnesses using the given layout and interconnect them as a single harness assembly, check the bundle continuity, bundle warnings and give annotations to the harness assembly.   INTRODUCTION Automotive Wiring Harness Parts Wiring…

                                                           WIRE HARNESS ROUTING - WEEK 4 AIM: Route the following harness layout in the Electrical workbench. Make assumptions…

1. AIM:    To Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. P clamp STEP 1: DOWNLOAD THE GIVEN PART FILE   STEP 2: CREATE A GEOMETRICAL PARAMETERS ENTRY, EXIT AND BASE PLANES WERE CREATED USING POINT…

AIM: To Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip.   Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html) Tyco…

AIM:-- For the Given Roof styling, create an ASSEMBLY by developing the essential flanges for the outer roof and creating the reinforcements. Provide appropriate dimensions and check for Draft analysis. Do a curvature study on the roof and perform calculations to determine the position of the Bow-roofs.…

FENDER DESIGN AIM: To design a  front fender of a car by following the given master section as per the design considerations of OEM. INTRODUCTION : Fender is the american english term for the part of an automobile, motorcycle or other vehicle body that frames a wheel well. Its primary propose is to prevent sand,…

 WHEEL ARCH CHALLENGE Aim :     To Calculate the Wheel Arch Area by given fender and Wheel Model Design and Prove whether the car will pass by using European standards or Not. Introduction : The wheel arch is the semicircular part positioned above the wheel of a vehicle. Designing of wheel arch…

OBJECTIVE:          To Calculate the section modulus for the previously designed hood and optimized hood.             To Come up with a new section that has improved the section modulus of the previous section.   SECTION MODULUS: Section modulus is the geometric…

HOOD DESIGN Aim: - The main objective of this project is to learn the essential tools, commands, and surface modelling of Hood designing using Siemens NX Cad. This project is to develop a design idea for hood BIW that satisfies the manufacturing requirements, functional requirements, and EURO NCAP standards.…

1.Write one page about Underbody coating and its purposes. Underbody Coating Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean.  The main purpose…

BENCHMARKING: Benchmarking is defined as the process of measuring products, services, and processes against those of organizations known to be leaders in one or more aspects of their operations. Benchmarking provides necessary insights to help you understand how your organization compares with similar organizations, even…

AIM: To develop the Door Trim panel OBJECTIVE: Creation of CAD model considering following inputs as like in OEM and tier1 companies a) Class A surface b) Nominal thickness : Refer master sections c) Attachment strategy :  Find a attachment strategy for the door panel complete work. Use Push pin with Dog house for…

A SURFACE DRAFT ANALYSIS:   TOOLING AXIS:     B SURFACE DRAFT ANALYSIS:   C SURFACE DRAFT ANALYSIS:   SOILD BODY DRAFT ANALYSIS:   FINAL BODY FLIP DIRECTION DRAFT ANALYSIS:   MASTER SECTION CREATION COMPARED WITH GIVEN INPUTS:   SIDE VIEW COMPARATION:   SIDE CORE AXIS CREATION:…

ASSEMBLY DESIGH 1:   BODY 1 DRAFTING:   BODY 2 DRAFTING:   BODY 3 DRAFTING :   BODY 4 DRAFTING:   BODY 5 DRAFTING :     ASSEMBLY DESIGH -2:   BODY 1 DRAFTING DESIGH:     BODY 2 DRAFTING DESIGH:   BODY 3 DRAFTING DESIGH:  

 A SURFACE DRAFT ANALYSIS:     B SURFACE DRAFT ANALYSIS:   C SURFACE DRAFT ANALYSIS:   SOILD BODY DRAFT ANALYSIS:   DOG HOUSE DRAFT ANALYSIS:   HEAT STAKES DRAFT ANALYSIS:   FOUR WAY LOCATOR DRAFT ANAYSIS:   ALL VIEWS: ISOMETRIC VIEWS:   TOP VIEWS:   FRONT VIEWS:  …

DRAFT ANALYSIS: A SURFACE DRAFT ANALYSIS:   TOOLING AXIS:   B SURFACE DRAFT ANALYSIS: C SURFACE DRAFT ANALYSIS:   FINAL BODY DRAFT ANALYSIS:   DOG HOUSE:   ALL VIEWS: ISOMETRIC VIEW:   RIGHT VIEW:   FRONT VIEWS:   LEFT SIDE VIEWS:  

DRAFT ANALYSIS: TOOLING AXIS CREATION:   A SURFACE DRAFT ANALAYSIS: B SURFACE DRAFT ANALAYSIS: FINAL BODY DRAFT ANALYSIS:     RIB CREATION REPORTS: TOOLING AXIS:   ROOT THICKNESS CHECKED:   SCREW BOSS : \   ALL VIEWS: ISOMETRIC VIEW:   FRONT SIDE VIEW:   BOTTOM VIEW:   TOP SIDE…

SOILD BODY: ISOMETRIC VIEW: FRONT VIEW:   TOP VIEW: LEFTSIDE VIEW:       A SURFACE DRAFT ANALYSIS:   C SURFCAE DRAFT ANALYSIS:   PART BODY DRAFT ANALYSIS: