CALCULATE THE CONCRETE MIX DESIGN FOR M35 GRADE WITH FLY ASH Aim: To calculate the concrete mix design for M35 grade with fly ash Introduction: REQUIREMENTS FOR PROPORTIONING OF M35 GRADE CONCRETE This section deals with conditions and requirements of the concrete to be made.   Grade Designation M35   Type of…

Aim: To sketch a G+1 floor residential plan according to Vastu Shastra and to list down the names of structural drawings required to be provided to the site of construction. Assume the size of structural elements ( column,beam ,slab etc.) and accordingly calculate the individual corresponding loads from the members according…

1. TITLE BLOCK   AIM: To Create Custom1- titleblock and Custom2-titleblock using Attributes and block command from Autocad software . PROCEDURE: Commands used: Line, Multiline text , block ,annotation Using line tool , draw the layout accordingly  Using mtext , insert the data given in the reference image …

1.Kitchen Layout: Aim:  To draw the layout and details of kitchen as shown in the figure. After sketching, need to provide the dimensions and text with the use of layers. All dimensions are in mm.   PROCEDURE: Comments used: Line , Offset , Qleader , dimension , layers Intially draw the plan . After drawing the…

Aim: To create layout of plan and section using Template mArch.dwt.To create viewport using MV command of size 400x445 and 375x445 and setting the scale (1:50) Editing Attributes in the template.Take a plot using A1 size. Procedure:In the command prompt enter "XREF" and on the left corner attach the Dwg.Attach the drawing…

  AIM:          To design and draft the layout of a residential building  Architectural drawing structural drawing PROCEDURE: Commands used: Line , Offset , Rectangle, Trim , Extend , Block , Block edit , Dimension , Layer , Hatch , Design centre. List of Rooms : PARKING LIVING ROOM…

  Aim:  To create a 3d Model of a drop column with panel using AutoCAD software. Introduction: Various commands used QNEW command UN command Box command Pyramid command Cylinder command Hide command FACETRES command REG command RO command MOVE command DIMLIN command Procedure: Type QNEW in command box, press…

   COMMANDS USED:- Line command Rectangle command UCS command Dimlinear command Region command Extrude command Substract command Box command Units command Dimstyle command 3Dface command 3Dorbit command Hide command Explode command Move command Copy command Dist command Solidedit command Union command Boundary…

AIM:  To create a 3D rendered model for a Residential Building in AutoCAD   2D tools: Line: The line object is the most basic and common object in AutoCAD drawings of any discipline. Each segment is a line object that can be edited separately, assigning properties such as layer, line type, and line weight.…

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level Aim: To model a ceiling from the architecture tab in the first floor level Procedure: Go to the architectural tab , select ceiling from that .   After selecting…

1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School Ans: I have chosen to build a Multi-Unit Residential Apartment . 2) Assume reasonable assumptions…

1. 1. Write the steps involved to upload a .std file through web mail?    2. Name the different materials that can be designed using STAAD Pro.    3. Is it possible to capture images in STAAD Pro? If yes how?    4. Name the three ways by which you can create a model.    5. Write…

1. 1. How will you assign Circular section to column?    2. How will you assign Unit system to a .std model file?    3. What are the parameters to be specified while using “Bay Frame” option?    4. Name few codal standards incorporated in STAAD Pro software.    5. How will you specify the design compressive strength for…

1) A)Observation: In this picture we observe that, concrete get damage/ broken and reinforcement are visible at the bottom of beam. The concrete spalled beyond the reinforcement that is indicates the segregation. The top portion of beam is not exposed due to covered from the slab projection so it’s look safe and…

1. Differentiate Static analysis and Dynamic analysis with proper representing pictures (30 marks) Static Analysis: Static analysis of structures considers static loads acting on the structure such as dead,live load which does not vary with time and are not considered to be sudden. In static analysis stiffness…

Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. The fundamental period of vibration (T1 = 2 seconds) and…

Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. Ans: Symmertry: It is observed that the distribution of mass,stiffness…

Question 1:The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account…

Question: Model a 25-storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 meters. Given data: Structural Element Sizes:  Beams: 300 × 400 mm …

1. 1. State the primary load cases to be considered for design.    2. What is One – Way slab?    3. What is the value of unit weight of structural steel and soil?    4. Name few sections that can be defined using Properties tab in STAAD Pro.    5. Define Primary Beams.…

                                                                                    PROJECT    …

Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo Introduction: Dynamo is an open source visual programming language for Revit, written by designers and construction professionals. Its a programminglanguage that allows you to type lines of code;  while also creating…

A)  AIM: To use the architecture/structural project file developed from week 6-8, Export the Revit file to Navisworks cache file. TOOLS/COMMANDS USED : Architectural file. file. Open Export. NWC. Navisworks. View.  3D view.  PROCEDURE : 1.the Revit file which is to be exported to the Navisworks file…

einforcement Detailing of Beams from ETABS output AIM - To Study The Reinforcement Detailing of Beams from ETABS output INTRODUCTION - ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis methods, and…

Aim: To Providing details of longitudinal reinforcement for the two columns from foundation to terrace level. Step 1: 1) Open a G+4 Etab file 2) Click the Concrete Frame Design tool 3) Select the Display Design Info option 4) Choose design output as Longitudinal Reinforcement Step 2: 1) After Selecting the Longitudinal…

Aim:   To run the analysis and design the RCC shear walls shown in the etabs model. Step 1: 1) Open the ETABS file 2) After the analysis click Concrete frame design Step 2: 1) Need to check there is any failures occurs 2) Click Shear wall design tool 3) select Display info and choose PM failure …

Aim:- To model and analyze the G+7 residential building from the given architectural drawings using the ETABS 2018. Introduction:- ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis methods and…

QUESTION:- Design a square footing for a column size of 400x400. The compression axial load for the load combination of (1.5 DL + 1.5 LL) is 2000 KN. The safe soil bearing capacity is 150 KN/m2 at a depth of 2 metres below E.G.L. Participants are free to go for either a tapered or stepped footing. Besides the total axial…

QUESTION:1 Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. ANS: AIM: To Analyze and designthe isolated footing from week 11 challenge on SAFE To verify the size, depth and steel provided as per calculations.  …

AIM:-To Create and Analyse the given building in ETABS 2018, the structural model has to be prepared in accordance with IS 1893 and as per IS 13920. To design the pile cap and pile reinforcement details,Tie  beam  connecting the pile caps, to sketch the column reinforcements, to produce the framing plan and beam…

1. Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must be as follows:      Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil  Hard soil Use Residential Purpose Safe Bearing Capacity 180…

1) Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition. The specification must be as follows:      Width  30m Length 50m Eave Height 9m Bay spacing 6m Soil type Medium Safe Bearing Capacity 200 kN/m2 Roof slope 1 in 12 Assume suitable sections for structural elements. Follow IS800:2007, IS1893…