What is Underbody Coating? Underbody coating provides long term protection from corrosion to car's underbody.Under body coating of car which are used in foreign have more underbody coating than car used in india due to their rules and regulation.   Types of Under Coating: Rubberized Undercoating. Asphalt-Based…

  Conclusion :   According to price wise Renault KWID is the cheapest after that Maruti baleno then Tata Tiago NRG and Toyota Glanza. The best mileage is provided by Maruti Baleno in both City and ARAI. Baleno has maximum fuel tank capacity. Brake Assist safety feature only available in Baleno.   After doing…

Sr No. Points Distance in mm Required Status 1. a  10 10  Pass 2 b  9.9490 10  Fail 3. c  -0.113949 10  Fail 4. d  -2.8875 10  Fail 5. e  -5.9973 10  Fail A  B C D E What is Fender : Fender is a part which covers a wheel.  To prevent water and mud spray,…

Defination Section modules: Section modulus is the ratio of bending to the farthest fiber from neutral axis, or it is the measure of the strength of the beam. Ratio of Area Moment of Inertia to the Distance from the Neutral Axis to the Point where the Bending Normal Stress is determined. Section modulus (S) = I/Y I = Moment…

FENDER DESIGN Objective: The main object of this project is to design the front fender's BIW(Body in white) using the fender skin data and the master section as the data by using NX CAD.   Introduction : Fender is the American English term for the part of an automobile, motorcycle, or other vehicle body that…

Aim- To develop the essential flanges and reinforcements with appropriate dimensions and checking draft by performing Draft analysis, Calculating Section inertia, Heat distortion and Snow load on the roof. Roof- An automobile roof or car top is the portion of an automobile that sits above the passenger compartment, protecting…

AIM: To design the back door of the carr and  make the inner panel for the back door and also design the necessary   INTRODUCTION: The trunk (North American English) or boot (British English) of a car is the vehicle's main storage or cargo compartment, often a hatch at the rear of the vehicle. It is also…

AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. DRAFT ANALYSIS: STEP 1: Check the connectivity of the…

DRAFT Draft angle is nothing but providing some tapered portion to the part for easy removal of the component from the mold during manufacturing. This is especially done in the case of plastic component design having a complex shape. Mostly the 3-degree draft angle is provided but it can vary depending upon the component…

AIM: To Create the Core and cavity blocks for the switch bezel component. DESCRIPTION:   1. CREATING TOOLING AXIS -                       The Tooling Direction is basically the direction that the mold pulls a part. The mold is built in two separate pieces,…

Aim: To create the Coin holder plastic Component through the given class A Surface. Objective: To Design Coin Holder as per automotive OEM standards. Create class B, Class C and Tooling Direction. Converting close surface into the solid part of 2.5mm thickness. Perform draft analysis to verify the creation of tooling axis.…

BUMPER DESIGN AIM: to make a model from the provided class-A surface.INTRODUCTION:CLASS-A SURFACE: a surface made by the designer which is given as an input to the plastic modeler to work on. It is aesthetic surface and the outer most surface. CLASS-B SURFACE: a surface below a certain thickness from the…

                                                                  Attachment Feature Creation (Ribs & Screw Boss) AIM: To Create the Door Handle Component…

AIM- Create the screw boss and dog house for the centre console coin holder considering the design rules mentioned in the video. General Rules for Screw bosses. Draft of 0.5 degree on walls of boss Thickness is 40% of the nominal wall at the base. Height to diameter ration-3:1 Fillet radius of max 0.25 mm.  …

ASSEMBLING THE BUTTERFLY VALVE COMPONENTS AND APPLYING GD@T TO THE ASSEMBLY DRAWING AIM:           TO ASSEMBLING THE BUTTERFLY VALVE COMPONENTS AND APPLYING GD@T TO THE ASSEMBLY DRAWING BY USING NX CAD SOFTWARE. INTRODUCTION: BUTTERFLY VALVE: A Butterfly valve is a quarter-turn rotational motion…

Advanced Sheet Metal Design Using NX Cad Challenge 1 Casing Design Title of the Project: Advanced Sheet Metal Design Using NX Cad Challenge 1 Casing Design Objective: To design a Casing with the help of NX advance sheet metal. Introduction: Depending on the material and production process, NX Sheet Metal offers…

TITLE OF THE PROJECT: Advanced sheet metal design using Siemens NX cad - Box Assembly. OBJECTIVE: To design a box assembly and create a draft of it using Siemens NX Sheet metal application. INTRODUCTION Metal that has been processed industrially into thin, flat pieces is known as sheet metal. One of…

   ODD SHAPED ENCLOSURE  OBJECTIVE :- To design an odd shaped enclosure and create a draft of it using Siemens NX Sheet metal application.  INTRODUCTION :-       Sheet metal is a procedure used to produce thin, flat sheets of metal. One of the basic materials used in metalworking…

Title of the project:- Advanced Sheet Metal Design Using NX Cad Challenge_6_Bracket Objective: To design a Bracket using Siemens NX Sheet metal application. Introduction:-   1. SIEMENS NX: Siemens PLM Software has acquired NX, formerly known as "unigraphics," since 2007. NX is a cutting-edge, high-end CAD/CAM/CAE…

METAL BRACKET USING NX SHEET METAL APPLICATION: OBJECTIVE: This is a project to learn the step by step procedure to create a Bracket with a gusset from the given 2D drawing. INTRODUCTION: A bracket is a connecting element used to secure one part to another. The weight is supported by it. The shape of brackets might vary…

Mixing Tee  Drive Link : https://drive.google.com/drive/folders/1n83SkhxKJfGEVN6I9kclNucOISDe2RdD?usp=sharing  Aim: To compare the mixing efficiency at 36°C for the hot inlet and 19°C for the cold inlet, set up steady-state simulations. To properly evaluate each strategy, try both the k-epsilon and…

AIM: Simulate the flow over a cylinder and explain the phenomenon of Karman vortex street. Understanding the vortex shedding for different Reynolds numbers by changing the inlet velocities accordingly. Create a monitor point behind the cylinder at a distance 4 times the diameter which can be used to calculate and analyze…