Giddamari Vamshi's Profile

Executive Programs

Workshops

Projects

Blogs

Careers

Student Reviews

For Business

Academic Training

Informative Articles

Find Jobs

We are Hiring!

All Courses

Choose a category

All Courses

Giddamari Vamshi

Mechanical Engineer

Skills Acquired at Skill-Lync :

MATLAB-BASICS

FEA

HYPER-MESH

RADIOSS

CRASH-WORTHINESS

STRUCTURAL-MESHING

SHEET-METAL-MESHING

LS-DYNA

Introduction

An enthusiastic Mechanical Engineer believes in continuous knowledge gain in the Domain of CAE Seeking an opportunity to showcase my skills and abilities in performing meshing/pre-processing and to be a part of an organization where I can fully utilize my technical skills to make a significant contribution to the success of the employer and individual growth.

8 Projects

1D Element Creation

Objective:

Question:- Mesh the Given component with the Size of 5 Units. Create 1D elements on the following component with given cross-section and DOF. a. Rod element:- Translational DOF should be Constrained with RBE2 link Cross-Section: BOX- Dimension a= 12 mm …

15 Mar 2022 06:19 PM IST

Week 6-Meshing of Hood Challenge

Objective:

OBJECTIVE:- The Aim is to Extract Midsurface of the Given Hood model and Meshing of the model using Hypermesh by considering the Quality Criteria given below and Generating mesh on the given component with low tria concentration and proper mesh flow. Target Element Length=5 Units Quality Criteria:- S.N …

15 Mar 2022 06:19 PM IST

Week 8-3D Tetra Meshing Challenge

Objective:

1. Create a Teramesh for Housing component with the following quality criteria. TetraMesh Generation Method:- 2D to 3D conversion Min element size:- 2 Units Max element size:- 7 Units Target element size:- 5 Units Tet collapse:- 0.15 Objective:- The main objecctive is to creat the tetramesh using the 2D to 3D conversion…

15 Mar 2022 06:18 PM IST

Week 9-Creation of 1D Connectors Challenge

Objective:

AIM:- Meshing of the given geometry. Provided below are the quality parameters that you have to follow. Target Element size = 5 Units S.N Quality Criteria Value 1 Aspect Ratio 5 2 Skewness 45 3 Warping 15 4 Taper 0.5 5 Min. Length 2 Units 6 Max. Length 8 Units 7 Min…

15 Mar 2022 06:18 PM IST

Week 12:Project-1-Meshing of Door Inner Panel Challenge

Objective:

Question:- Follow the Quality Criteria and mesh the given Side door component and assign thickness: Target Element Length = 4 Units S.N Quality Criteria Value 1 Aspect Ratio 5 2 Skewness 45 3 Warping 15 4 Taper 0.5 5 Min. Length 2 Units 6 Max. Length 6 Units 7 Min angle Quad 45 8 Max…

26 Nov 2021 06:25 AM IST

RADIOSS

Week 12:Project 2-Meshing of Rear Wheel Holder challenge

Objective:

Question Follow the below-mentioned quality criteria, mesh the given rear wheel holder component and assign thickness to it with a Target Element Length = 5 Units S.N Quality Criteria Value 1 Aspect Ratio 5 2 Skewness 45 3 Warping 15 4 Taper 0.5 5 Min. Length 2 Units 6 Max. Length 8 Units 7 Min angle Quad 45 8…

16 Feb 2022 04:49 PM IST

Assignment 1-2D Meshing Challenge

Objective:

OBJECTIVE: To Carry out the geometry cleanup operation on the given 3 files. Practice Clip Repair Mounting Bracket There should not be any free edges, convert all of them into refine geometry. Clean the geometry. Extract midsurface. Clean midsurface geometry. Ignore holes less than dia 5mm. Create 2D mesh…

03 May 2022 07:25 PM IST

Assignment 2-RADIOSS Engine File Editing & 3D Meshing Challenge

Objective:

Questions: 1. Check the material properties of the rail component and calculate the speed of sound in steel rail=_______ 2. The length of the rail is about 1000 mm.calculate the time takes for a shock wave to travel from one end of the rail to the other. 3.Time for sound to travel length of rail=______…

14 May 2022 06:27 PM IST

Showing 1 of 8 projects

1 Course Certificates