Anton Paul
Automobile Engineer who wants to innovate, grow and teach.
Skills Acquired at Skill-Lync :
Introduction
14 Projects
Hood design
HOOD DESIGN AND DEVELOPMENT Objective: Design and develop a hood for a vehicle with reference to the provided outer panel design and provide requisite reinforcements and strengthening structures per required safety regulations, NVH limitations and design constraints. …
17 Mar 2020 08:09 AM IST
Section modulus of hood
SECTION MODULUS OF THE HOOD Objective: To find the section modulus of the hood and make modifications to the section to improve it. Software: Siemens NX 12 Description: …
05 Jan 2020 11:17 PM IST
Underbody coating process and adventages
UNDERBODY COATING Underseal (often called undercoating in the U.S.) is a thick resilient coating applied to the underbody or chassis of an automobile to protect against impact damage from small stones, which would rapidly chip ordinary paint, allowing rusting to begin. The rate at which vehicles corrode is dependent…
17 Mar 2020 08:09 AM IST
Roof Design
DESIGN OF ROOF Objective: Design a roof using the provided skin data and also position bow roof rails in accordance with heat distortion and snow weight formula also find section modulus of the roof and roof rails and check the draft of the designed parts. Software:…
17 Mar 2020 08:09 AM IST
Benchmarking for customer requirements
17 Mar 2020 08:09 AM IST
Wheel arc calculations for fender
WHEEL ARC CALCULATION FOR FENDER OBJECTIVE : Calculating the wheel coverage by wheel arc of the given fender and checking if it complies with European regulations. SOFTWARE Siemens NX12 European Regulation:…
17 Mar 2020 08:09 AM IST
Week 6:- Clamp Unit & Pin-Clamp Unit Design Challenge
OBJECTIVE: Design 3 different types of Pin-Clamp Unit with different Riser, Blade and Clamp Arm for the given Car Panel. SOFTWARE: CATIA V5 R21 PARTS SWIVEL CLAMP: Clamp Cylinder: Clamp cylinder uses compressed air to actuate a piston that produces a force linear on the required part. Pneumatics are…
03 Jul 2020 07:57 AM IST
Week 7- Base Unit Design Challenges 2
AIM: Design a base unit with all required weldments and pedestals as required by the fixture. INTRODUCTION: A base unit is a steel or aluminium plate of 20-40mm to which all other pin and clamp units are attached. It must also provide space for parts like a pneumatic controller, eye bolts, pneumatic cable trunking paths…
24 Sep 2020 07:13 AM IST
Week 8:- 3D Finishing Challenge 2
Aim: To perform 3D finishing and create rough locators for the assembly fixture. Introduction: It is the process where the fixture is checked in various parameters like hole concentricity, machining area marking, resolving clashes etc. This is the stage in the process where the position of the rough locators is also…
03 Dec 2020 01:21 PM IST
Week 9:- 2D Detailing Challenge
WHAT ARE DRAWING TEMPLATES? Drawing templates are the basic drawing standards for a specific customer. Drawing templates are used to detail the different parts and features of the unit. Templates are used to denote various details and features including tolerances, measures, finishes, name of parts and assemblies…
12 Feb 2021 01:48 PM IST
Week 10:- 2D Detailing Challenge
AIM: To draft a Key sheet, Base unit, and Fix pin unit designs with all required child parts. SOFTWARE: CATIAV25 INTRODUCTION: Body in white (BIW) refers to the stage in automobile manufacturing in which a car body's components have been joined together, using one or a combination of different techniques:…
14 Jun 2021 06:58 AM IST
Week 11:- 2D Detailing Challenge 2
AIM: To create clamp and pin unit 2D drawing for the required 3D model and create separate child parts. SOFTWARE: CATIA V25 INTRODUCTION: A Fixture is a device that holds the workpiece or pieces in place while it’s being worked on. It holds it in place by arresting all the degrees of freedom using the…
03 Sep 2021 11:17 AM IST
4 Course Certificates
Automotive Sheet Metal Design using Siemens NX CAD / CATIA V5
1 Workshop Certificates
Introduction to Advanced Driver-Assistance Systems (ADAS)
Academic Qualification
B.E
Sree Sastha Institute of Engineering and Technology
01 Mar 2011 - 02 Mar 2015
12th
SBOA School
01 Mar 2010 - 01 Mar 2011
10th
SBOA Matriculation and Higher Secondary School
03 Mar 2008 - 02 Mar 2009
Here are the courses that I have enrolled
Similar Profiles
Ladder of success cannot be climbed with hands in pocket.
The Future in Motion
Give more than what you get you will get more than what you gave
Avid learner