Lesson finished
Unlock all 19 lessons of Introduction to Aero-Thermal simulation using ANSYS FluentFull course ₹40,000 · paid
Aerodynamics Basics: Speed of Sound, Pitot Tubes and Forces
A free lesson from Skill-Lync's Introduction to Aero-Thermal simulation using ANSYS Fluent course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Introduction to Aerodynamics in Aero Thermal Simulations using ANSYS Fluent”
What will you learn in this free Introduction to Aero-Thermal simulation using ANSYS Fluent lesson?
The instructor defines aerodynamics and its role in aircraft, cars, HVAC and buildings, then derives mass flow rate and the speed of sound under isentropic and isothermal assumptions. He covers static, dynamic and total pressure with pitot tubes, isentropic relations, similarity parameters, and lift, drag and moments.
- Mass flow rate equation: m-dot = rho A v
- Speed of sound from bulk modulus and density
- Static, dynamic and total pressure; pitot tubes
- Lift, drag, normal and axial forces on an airfoil
What comes after lesson 3?
Later in Skill-Lync's Introduction to Aero-Thermal simulation using ANSYS Fluent course (paid): lesson 4, International Standard Atmosphere; lesson 5, Introduction to Aero Thermal Simulations Using ANSYS Fluent; lesson 6, Introduction to ICE and CFD. The full course has 19 lessons (6 h 43 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Hey guys welcome to this video from the course Aerothermal Simulations using Ansys Fluent. In this particular video you will get an introduction to aerodynamics. In this video you will learn what exactly aerodynamics is, the role of aerodynamics in designing a particular product and then we'll take a look at parameters that you need to be aware of while studying aerodynamics. These parameters are the mass flow rate, the speed of sound and bulk modulus. And then we'll go on to considering the propagation of sound in air as an isentropic process and deriving some of its parameters.
And then we'll also consider it as an isothermal process and then calculate the speed of sound. And after that we'll take a look at some of the instruments used in aircrafts which are the pitot tubes. After this we'll derive some of the isentropic relations that you need to be aware of while doing calculations in aerodynamic studies. Then we'll look at what similarity parameters is and then we'll finally conclude the session by taking a look at aerodynamic forces and moments. There are different interpretations as to what exactly aerodynamics is.
One of the first statements was given by the father of aerodynamics himself, Ludwig Prandtl. He stated that aerodynamics as a term is generally used for problems arising from flight and other topics involving the flow of air. The 1969 edition of American Heritage Dictionary defined aerodynamics as the dynamics of gases, especially that of atmospheric interactions with objects. In this definition, they've taken into account the interaction of fluids with other objects as well. But in simple terms, what might have come to your mind or what people usually assume is that it's the study of motion of air and its interaction with other objects.
And here you can see the interaction of air with the body. So apart from this, there are other applications of aerodynamics and let's take a look at them. Here you can see aircraft during different eras and shapes. You can see how they evolved according to their function. The Douglas DC-3 aircraft was a World War II airplane. In the next figure, we have the Boeing 707, which was also prominent during the same era, but used for passenger aircrafts. The Lockheed Martin F-22 was one of the most advanced fighter jets of its time.
It is capable of going into supersonic speeds unlike the other two. And now if you take a look at the body, the fuselage and the wings were separate. You can see that the fuselage and wings are blended together. Hence the name blended wing aircrafts. The role of aerodynamics is not limited to aircrafts alone. Automobile manufacturers have, in recent years, focused on the shape after studying its effects. You can identify how the box shape of automobiles have changed to a more curvy and aerodynamic one. When it comes to race cars, the manufacturers chase the ultimate design that will get them ahead of the competition.
The study of the aerodynamics of a race car is not just to attain top speed. The car also needs to be grounded at this speed. So what do I mean by grounded? If you check YouTube, you can find videos on how Peter Dumbrecht's Mercedes CLR just took off from the track at Le Mans 1999. If proper analysis had been carried out back then, then such a devastating event would not have taken place. Next, we'll take the example of temperature control of a building, which is done by an HVAC system.
All these systems depend on the airflow around them or inside them for their proper functioning. So in order to maximize their efficiency, aerodynamic studies are carried out. You might not have known this, but aerodynamic studies are carried out on flow around buildings as well. This is to calculate the wind loads and the effect one building has on the other. But keep in mind that these are not the only areas of application. There are many more. But by now, you would have gotten a brief idea as to where aerodynamic analyses can be carried out.
Now, let's take a look at some quantities that we need to remember while studying aerodynamics. We'll be starting with the mass flow rate and what it is. Well, the mass flow rate is exactly what the name indicates. It's the rate at which mass flows through a particular section at a particular moment in time and is represented by m dot. You all might be familiar with the equation of mass flow rate, but let me tell you how it's arrived at. And in order to do that, let me take this converging diverging nozzle.
Let's just consider this small section at the inlet. This section has an area A and thickness of dx. So the mass of this section will be the density of the fluid multiplied by the volume. This is from the formula of density that we are all acquainted with. Now, the volume of this section is the area multiplied by the thickness, which is dx. So now we get the mass of the fluid to be density multiplied by area and dx. To obtain the mass flow rate, we need to take the time derivative of mass.
So by differentiating mass with respect to time, we get the term dx by dt on the right-hand side. Well, this is actually velocity, right? And that's how we get the equation for mass flow rate to be m dot equals rho Av. So let's consider this nozzle again. It has three sections, one, two, and three. Section one is the converging part. The section two is the diverging part. And section three is the throat of the nozzle. Now, we know that mass is conserved in a closed system, right?
So the mass of the fluid entering the system is equal to the mass exiting the system. This is according to the law of conservation of mass. So we can form an equation as m dot 1 equals m dot 2 equals m dot 3. And we can replace this with the quantities derived here. Since density is constant throughout a flow, we can take the equation to be A1 V1 equals A2 V2 equals A3 V3. What we can decipher from this equation is that in order for mass flow rate to remain constant, the velocity of the fluid increases at sections where area decreases and vice versa.
So by using this equation, we can find the velocity of the fluid at any section in a closed flow system. So with this, let's move on to the next section. Now we'll be discussing what exactly the speed of sound is. Let's take an example of a bell placed in the medium of air. If you ring the bell, the molecules of air near the vicinity of the bell gets disturbed. These disturbed molecules interact with other molecules and this carries on. What we hear as sound, this disturbance in the form of pressure waves as seen here.
Since sound is a sensation that is perceived by humans, it can vary depending on the speed at which it travels. The speed at which sound travels is dependent on the bulk modulus and density of the media. It's related according to this formula. This was determined from experiments. In normal atmospheric conditions and at sea level, the speed of sound was determined to be around 340 meters per second. According to the formula, A equals square root of gamma RT. Here A is the speed of sound in medium.
Gamma is the ratio of specific heats. R is the gas constant. And T is the temperature. Temperature is usually taken in Kelvin. Now in aircrafts, the speed of sound is concerned when they take into account a term called as Mach number. The Mach number is the ratio of the speed of the aircraft to the speed of sound. If the speed of aircraft is greater than the speed of sound, the aircraft is considered to be in supersonic speeds. The interaction of air with the aircraft changes as the speed increases.
It can affect the structural integrity of the aircraft at the end. But we don't need to go into detail about it right now. We'll go into the specifics of how this happens in later videos. The speed of sound in any medium can be determined with the help of the formula V equals square root of K by rho. The bulk modulus relates volumetric stress to volumetric strain. Now what does that mean? So if you drop a small rubber ball into water, it will experience a pressure on all sides, which is the volumetric stress here since it acts equally from all the sides.
Since the pressure tries to compress the ball, there will be a decrease in volume. And here is where we look at volumetric strain. Now volumetric strain is a ratio of change in volume to the original volume. In this case, since the pressure acts from all sides and compresses the body, volume decreases. And hence volumetric strain is negative. Now having a negative term here will lead to complications in calculations. So in order to make the quantity of bulk modulus positive, we add a negative term to volumetric strain.
And hence we arrive at the formula for bulk modulus as shown here. Now the unit of bulk modulus is given by the same unit as that of pressure. Performance with Leuteick is given by theătruc. Forặ esp час și 4%. Here is the length ofуже其實. which is pascal. Now the change in volume depends on the object and is quantified. So if we take the case of steel, it will have a very high bulk modulus of 139 gigapascal. But if we take the case of air, it will be very less with a value of 0.0001 with a value of 0.0001 gigapascal.
The thing is that it's very hard to compress steel, right? But that's not exactly the case with air. You can easily crush a plastic bottle and it would only depend on the grade of the plastic. So if you take a look at the values of bulk modulus for these two materials, we can say that it's difficult to compress steel with a high value of bulk modulus, while it's very easy to compress air. Now this is how the term compressibility is related to bulk modulus. It's inversely proportional to bulk modulus and is represented by the term beta.
Now having discussed all those properties, let's go into deriving the speed of sound in a medium of air. Propagation of sound in air is considered to be isentropic, and hence the equation PV raised to gamma equals a constant will hold true. On differentiating this equation, we get P gamma into V raised to gamma minus 1 into DV plus V raised to gamma into DP equals 0. Now if we rearrange the terms in this equation into this form, we get negative DV by V dP equals 1 by P gamma.
So the term on the left is actually compressibility, which is negative DV by V dP. Now if we substitute the value of beta, in our previous equation, we get beta equals 1 by P gamma. Now we know that beta equals 1 by K, where K is bulk modulus. Now here we get 1 by K equals 1 by P gamma. Now let's recall the formula for speed of sound, which is V equals K by rho. Now substituting K, we get V equals root of P gamma by rho.
Now air is a calorically perfect gas. So the equation P equals rho RT holds true. Now if we substitute P equals rho RT into this equation, we get that V equals root of gamma RT. Now at ground level, the properties of air are termed to be at STP, which is standard temperature and pressure. The values of which are T equals 288 Kelvin, P equals 101325 Newton per meter square, and rho equals 1.22 kilogram per meter cube. Now substituting all these values into our previous equation of V equals root of gamma RT, we get V air equals 340 meter per second.
Now this can be taken as the reference speed of sound in air at ground level. Now generally, as I mentioned, propagation of sound in air is taken as an isentropic process. So all these values hold true in these conditions. Now what happens in an isothermal condition? Well, let's take a look at that. The equation of state is P mu equals RT. Here mu is the specific volume, which is 1 by rho. So substituting 1 by rho here, we get P by rho equals constant, since R and T are constant.
We can also take it in this form. And once we differentiate it, we get nu dP plus P d nu equals 0. Now we take P d nu into the right-hand side. Now we take nu dP into RHS and P to the LHS. We get the equation in this form. Now as discussed earlier, compressibility is negative dV by V dP. Since nu is the inverse of density, we can rearrange the terms into negative dV by V dP. Hence we get compressibility equals 1 by P. Now compressibility equals 1 by bulk modulus, and hence we get k equals P.
Now if we substitute it into the speed of sound formula, which relates bulk modulus and density to the speed of sound, we get V equals root of P by rho for an isothermal condition. Now if we put the values relevant to water, we get velocity of sound in water as approximately equal to 1500 ms. Now to put that into perspective, we have speed of light equals 3 into 10 raised to 8 ms. Speed of sound in air is 340 ms. And speed of sound in water is 1500 ms.
So as the density of the material increases, the velocity of sound in that particular medium increases as well. Now let's look at pressure before we move on to the next sections. Pressure has two components, which is a static component and a dynamic component. Static pressure is the pressure exerted due to a particular state or position, while dynamic pressure acts due to the motion of fluid. Now static pressure is usually due to the weight of the fluid alone. So when you combine both of them, you get total pressure, and this represents the total energy of the fluid.
So the momentum equation in one dimension is given in this formula. So the total energy of the fluid is determined by the total pressure. Now let's see how the formula for each type of pressure is derived. So let's take the formula for momentum equation in just one dimension. And if we take RHS to LHS, we get the equation in this form. Now U is a function of X. So we can take this inside, and then the equation turns into this form, which is dP by dx plus d by dx into rho U square by 2.
So you can check it by differentiating this particular term. Now since we're differentiating both terms with respect to dx, we can club them together to obtain d by dx of P plus rho U square by 2 equals 0. Now if we integrate it, we get P plus rho U square by 2 equals a constant. So this term is actually the total pressure, which is a combination of static pressure and dynamic pressure. Now the velocity U of a particular flow can be calculated from the term dynamic pressure.
Now why did we need to know all of these? These equations are actually used in instruments used in aircrafts, which is called a pitot static tube. The pitot static tube measures pressure. And from this pressure, the pilot can get a reading of the velocity of the plane. Now the pressure measurement is used for other readings for the pilot, such as the altimeter and the airspeed measurement. Now there are three types of pitot tubes, simple pitot tube, a static pitot tube and pitot static tubes. The pitot tube is generally of this shape.
It is connected to a sensing instrument where the pressure is sensed. The simple pitot tube just measures the total pressure of the incoming fluid. Now this includes a static as well as a dynamic component. But if you see the static tube, this end is closed while there's an opening at these two ends. So the reading that you get here is actually the static pressure, which is sensed by the instrument here. Now if you take a look at the third type of pitot tube, this is the pitot static tube, which is a combination of both.
It has an inlet here for measuring the total pressure and two inlets by the sides to just measure static pressure. By taking the difference of total and static pressure, one can obtain the dynamic pressure as well. Now let's look into pitot static tubes a bit closer. This image perfectly represents a pitot static tube. The incoming air is coming from this side. It's hitting this elbow and it's going to the pressure sensing instrument, which measures the total pressure. Now the static pressure is sensed in this circuit with the pressure sensing instrument.
The pressure transducer at the middle will give you a perfect reading. Now measurements will be accurate at low mark conditions, particularly for incompressible flow. Don't worry about what it is. We'll get it into the specifics in later videos. Now planes such as the Boeing 707 and other small aircrafts use pitot static tubes. You can still see them in the airplanes of today, along with other advanced instruments. Now, before we go into deriving isentropic relations, let's briefly discuss about what a stagnation point is. Take this airfoil.
When the incoming air is hitting the airfoil, you can represent it by three such streamlines. Now, if you take one particular streamline that hits the tip of the airfoil, it will come to an end here. At this point, the velocity is zero. That means the flow has stagnated here. And hence, this point is called the stagnation point. Now, just because the velocity is zero, does it mean that the other properties are zero as well? There will be a temperature and pressure associated with this point, which is usually represented by P0, P0, et cetera.
Now, this piece of knowledge is required for when we enter into the later sessions, where we derive the isentropic relations. Now, at far field, that is, at a point away from the body under observation, the conservation of energy is given by H0 equals H plus V square by two. Here, H is the enthalpy, V is the velocity of the fluid. Now, we know the formula for enthalpy. which is CP into delta T. So substituting that, we get CP into T0 equals CP into T plus V square by 2.
Now, if we take CP onto the denominator here, we get T0 equals T plus V square by 2 CP. Now, we know that the Mach number is given by V by A. So, we can substitute V equals MA here and obtain the equation as T0 equals T plus M square A square by 2 CP. Now, we know that A equals root of gamma RT. So, the equation then becomes T0 equals T plus M square gamma RT by 2 CP. Now, let's turn this equation into another form.
We know that CP minus CV equals R and CP by CV equals gamma from basic thermodynamic relations. We can turn CP equals gamma into CV into this form. And then, let's take CP into one side. Now, CP into one minus gamma equals negative gamma into R. So, if we rearrange the terms, we get CP equals gamma R by gamma minus 1. Now, if we insert the value of CP into this particular equation, we get T0 equals T plus M square gamma RT into gamma minus 1 by 2 gamma R.
We can cut gamma R from the denominator and numerator and we get the equation in this form. Since we have T on both terms, we will take T as common and then take it to the LHS. Now, we have T0 by T equals 1 plus gamma minus 1 by 2 into M square. Now, this is the equation that relates temperature to the Mach number. This is the first part of the isentropic relations. Now, let's relate pressure, density, and then temperature. In an isentropic relation, S2 minus S1 equals 0, where S is the entropy of a state.
Now, S2 minus S1 equals CP natural log T2 by T1 minus R into natural log of P2 by P1. I'm not going to discuss about how this equation came into place. You will just have to go back to your thermodynamic textbooks to know how this equation came into play. Now, since S2 minus S1 equals 0, we can rearrange the terms as this. Now, taking the anti-log, we get T2 by T1 equals P2 by P1 whole raised to R by Cp. Earlier, we discussed that Cp minus Cv equals R and gamma equals Cp by Cv.
Now, if we substitute the values of R and Cp here, we get Cp minus Cv by gamma into Cv. If I take Cv from the numerator, we get R by Cp equals gamma minus 1 by gamma since Cp by Cv equals gamma. Now, the above equation becomes T2 by T1 equals P2 by P1 whole raised to gamma minus 1 by gamma. This is how pressure and temperature are related in an isentropic process. Now, for the relation between density and temperature, let's take a look at this equation, specific volume initially.
Now, we can convert this as S2 minus S1 equals Cv natural log T2 by T1 plus R log rho 1 by rho 2. Since we are considering isentropic behavior, this equation becomes Cv natural log T2 by T1 equals negative R natural log rho 1 by rho 2. Now, again, if we take the anti-log, we get the equation in this form. So, if we change the equation again and try to remove the negative here, we get T2 by T1 equals rho 2 by rho 1 whole raised to R by Cv.
Now, according to the earlier relations, R by Cv equals gamma into Cp minus Cv by Cp. Now, if I take Cp from the numerator, I get the equation in the form R by Cv equals gamma into 1 minus 1 by gamma, which is R by Cv equals gamma minus 1. Now, density and temperature are related by T2 by T1 equals rho 2 by rho 1 whole raised to gamma minus 1. Now, let's recall the initial equation which relates temperature to the Mach number. Now, we just have to substitute the equations relating pressure to temperature and get the equation in this form.
And then, when we use the equation relating density to temperature, we get the equation in this form. These three equations are called isentropic relations, which helps you to identify the stagnation pressure, temperature and density and related to the Mach number. Now, to summarize, for an incompressible flow, that is, at low Mach numbers, total pressure equals static pressure plus dynamic pressure. For compressible and high Mach flows, we have the equation in this form. Now, solving for pressure, density or temperature at incompressible low Mach flows is actually less time consuming when compared to solving pressure at compressible high Mach flows, since the equation is slightly more complex.
Now that we've discussed the isentropic relations, let's get into the next part. Well-known aircrafts such as the Boeing 747 and the Airbus A380 fly at altitudes of around 10 kilometers above sea level. Now, wind tunnel testing is carried out to determine the performance of aircrafts. The Boeing 747 is a huge plane. Building a wind tunnel to test its performance is going to be really expensive. So, alternately, what is being done is that a prototype of the aircraft is used while testing. The prototype will be a scaled-down version of the aircraft that is to be tested.
So, I hope you all know what a prototype is. The prototype will be similar in shape and similar in dimensional ratios, such as the length to diameter ratio and the shape of the body. But apart from this, there are other parameters that need to be similar. That is, we need to attain flow similarity as well. Now, by attaining flow similarity, we can ensure that the prototype is also experiencing the same conditions as the original plane would at higher altitudes at ground level itself. So, there are four parameters that we need to check for flow similarity.
That is, Reynolds number, the Mach number, the Prantle number, and Knudsen number. The Reynolds number is a ratio of inertial force to viscous force. The Mach number is a ratio of velocity of the body to the velocity of sound in air. And the Prantle number relates momentum diffusivity to thermal diffusivity. The Prantle number is usually used when thermal effects come into play. Now, the Knudsen number gives you an idea of the density of a particular fluid at a particular condition. Let's look into this in more detail.
Consider different types of flow. Stokes flow, which is basically a creeping flow where velocity is almost equal to zero, needs only the Reynolds number to attain flow similarity. In incompressible flow or low Mach flows, we only need Reynolds number as well. If you recall the equation for pressure in incompressible flows, we know that there is no Mach number there. But when compressible flow comes into play, the Mach number is required to calculate pressure, density, and temperature. Now, when the flow goes supersonic, that is, when the object is moving at a faster rate than the speed of sound, then we need Prantle number because thermal effects come into play.
Now, when the flow goes hypersonic, we need the Knudsen number because hypersonic flow is usually observed on spacecrafts where the density of air is very less. Now, let's move on to the last topic for this video, which is aerodynamic forces and moments. This will be a brief recalling of what exactly are the forces and moments experienced by a body traveling through a fluid. Now, the forces on a body, such as an airfoil here, when it travels through a fluid is mainly due to two reasons, pressure and shear force.
Now, pressure force acts normally to the body and shear force acts tangentially to the body. Now, depending on the pressure and the shear force, two forces act on the body, which is the lift force and the drag force. The lift force and the drag force acts at a point called the center of pressure, which is distant from the center of gravity of the body, which causes an aerodynamic moment on the body. Let's take a closer look at what it is. So, let's consider this airfoil at a particular angle of attack.
By angle of attack, I mean that the axis of the airfoil is not in line with the velocity vector that is shown here. You can see that the axis makes a line through here and the velocity vector is here. So, alpha is the angle of attack. So, you can see here that the weight acts at this point. So, let's consider that for this airfoil here. So, this will be the center of gravity. But, as the airfoil moves through air, different forces will act on it. And this is considered to be at the center of pressure.
So, you can see here four forces. Lift force, normal force, drag force and the axial force that is acting from this point. Since there is a difference between the center of gravity and the center of pressure, this creates an aerodynamic moment. Now, the forces that act in line with the axis of the body is called the normal force and the axial force. While the forces that act in line with the velocity vector is called the lift force. But, so, here it is divided by the lift force.
Thank you. And the drag force. Now with that we will conclude this particular video. Now in the next set of videos we will be going deeper into what exactly drag force, lift force, etc. are. So let's summarize. Now in this video we discussed about what aerodynamics is and its role in the industries such as aeronautics, automobiles, HVAC, and construction. We discussed about a few important parameters which were the mass flow rate, the speed of sound, and bulk modulus. Then we derived the speed of sound in both isentropic and isothermal conditions where the isentropic condition was considered to be the propagation of sound in air and the isothermal condition was considered to be the propagation of sound in water. Then we saw the stark change in values of the speed of sound. Then we discussed about static pressure and dynamic pressure and how pitot tubes are used to calculate velocity and altitude using this formula.
Then we derived important isentropic relations which related pressure, density, and temperature to the Mach number. And then we compared the formulas for pressure at low Mach numbers and pressure at high Mach numbers. We saw that at high Mach numbers or at compressible flows the equation for finding out pressure was a bit more complex. Then we discussed about similarity parameters to ensure dimensional similarity and flow similarity. Then we concluded the video with a brief discussion of aerodynamic forces and moments. Well, that's all for this video and I'll see you again in the next one. Thank you.