← Previous lessonFree lesson 3 of 3 · lesson 3 of 5

Unlock all 5 lessons of Advanced CFD Meshing using ANSAFull course ₹40,000 · paid

Price & syllabus
Free lesson · 121 min · no payment

Closing and Volume Meshing a Turbocharger Model in ANSA

A free lesson from Skill-Lync's Advanced CFD Meshing using ANSA course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “3.0 - 3D (Volume) meshing to Turbocharger”

What will you learn in this free Advanced CFD Meshing using ANSA lesson?

The instructor cleans a raw turbocharger by deleting overlapping surfaces, using intersect, release and topo, and patching open areas until the model is closed. After naming PIDs and surface meshing at 5 mm, 2 mm and 1 mm, the lesson auto-detects eight volumes, keeps the four fluid volumes and builds a Tetra CFD mesh.

  • Removing overlapped surfaces and unwanted triple cons
  • Intersect, release and topo tools
  • Different mesh lengths for different PIDs
  • Keeping fluid volumes and deleting thickness volumes

What comes after lesson 3?

Later in Skill-Lync's Advanced CFD Meshing using ANSA course (paid): lesson 4, CFD meshing to BMW M6 Model inside Wind tunnel; lesson 5, Surface wrap to an Automotive assembly. The full course has 5 lessons (12 h 29 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Part 1

Hello guys. So in the previous classes, we worked with pressure wall and a simple cylinder and we learned how to do the topo cleanup, how to do geometry checks and then how to give mesh length and then match that particular components after assigning so many PILs. So till now, we have learned about few topo tools, few mesh tools. Now in this particular week, we will also learn about volumetric mesh. So this is double charger model which we will be working in this particular week. And we will also see what is the volumetric mesh and how to perform the volumetric mesh for this double charger model.

So let's get started. So this is basically double charger model. And this is very raw model on which we are supposed to do some topo cleanup. Right. So there are also few PIDs assigned. But we need to change that PIDs and then we need to give the appropriate PIDs. So we will correct this PIDs once after we finish with this topo cleanup. The first task should be to correct the topo cleanup. So as we discussed in the previous classes, whenever you see any glitchings, just understand there should be some overlapped surface.

Right. So here you can see few surfaces are having some glitchings, which we can consider it as overlapped surface and we can directly delete that. If you want to check whether the overlapped surface are present or not, we can also perform the topo. And we will check with the triple cons. If you perform any topo and if you can see the triple cons, just consider that should be some overlapped surface present over there. Also, whenever you see the single cons, consider that there is a surface missing at that particular location.

As you can see over here. So now it's our task to solve the possible triple cons and the single cons. After we do that, we'll go with the geometry checks. We'll confirm everything is correct and then we'll assign the PIDs. So let's get started with this overlap surfaces. So first of all, we'll try deleting the surfaces directly. We'll see what surface they are deleting. So here we can see they have deleted the surface. But again, we are not sure whether the required surface is also getting deleted or not.

So we'll do control Z. We'll have the surface back. We'll start deleting from the top. So we can use this, you know, it's a deleted option. We'll find out the crosshatch and then we'll check with the selection. The selection is perfect. No. So selection was not perfect. So I'll do control Z. So what is happening? We are basically deleting this green color surface, which we don't want to delete, but we want to delete this. Particular pink color of surface. So now it's our task to find out the pink color crosshatch so that we can select that crosshatch and we can delete the surface.

Basically, the color of the crosshatch will be same as the color of the PID. Oh, we'll see. Yeah. So here we found pink color crosshatch. So basically we can try deleting the surface from here. We'll select over here like this. So it's selecting one surface. Let us try selecting the same by using PID region. OK, so it's selecting entirely surface. We'll see what can be done if we delete that. So I tried deleting that and it deleted most of the overlap surface as I can see in my screen is also surface present over here.

So again, I'll try picking this pink color surface. So in order to pick that, we can also do another thing. We can try hiding this green color PID and we'll see what is available over there. So we can see that these two surfaces are unwanted and are present over there. So we can directly go there and delete this too. Once we do so, we'll again call everything and we'll see if any glitchings are present at that location or not. Basically, we'll not find that. Here we can see that is an extended surface present over here.

We'll try to select that by selecting everything. So you can consider that we have selected this PID region. That is why it's selecting everything. So I'll do right click, go with entity and then we'll select this. Selecting fully. So let's try deleting this and we'll see. So it's deleting everything. Even though it's deleting everything, we can still create a new surface by using new Koons option. So you can always create a new surface by using Koons or Fitter. Let us try with Koons option here. So if you want to select each and every single Koons together, you can basically use the loop option.

If you use entity option, it will only select one, one edge, second edge, third edge, separate. So like this also, you can create a new surface. It will show you a preview and then you can confirm by clicking on OK. Like this way. Or else I'll do CTRL Z and I'll show you the loop option, how it will work. So click on new Koons. Select the loop option and then select only on one curve. And it will select each and every cons over there like this.

You can also confirm your selection by CTRL SHIFT by going in a wireframe mode and you can check the selection. You should not miss any single cons in order to have a very good and desired surface over there. So this is fine. We'll do middle click and we'll click on OK. But this thing is much clearer because we are not able to see any single cons and the triple cons also. Like with the other regions, if we have any other region where triple cons is present or single con is present.

So here we can see there is a single con present. So we can also create a new surface in the same way how we did over here. There is some complexity over here. As you can see, the surface is not a flat one. So it's having this much breadth over here and then breadth will increase as this box is interfering in between. We'll still try creating this by using this cons option with the loop option. We'll select this. You can see the selection is not happening now.

So what we'll do, we'll try selecting this one by one. Before that, we can also see there is a glistings present over here. We can consider that some duplicate sub is also present. That is why the triple con is forming there. So we don't want to delete this green color object. Instead, we want to delete this pink color object over there. Also, we'll check whether we have any other overlap surface present over here or not. Here also we found a triple con. So basically there also. Here also.

So we still have a few locations where we have duplicates. So I'll do the same thing. I'll try hiding my green color PI differently. And we'll able to see this duplicated surface. I'll go and we'll delete that one by one. Make sure you are selecting the desired surfaces, not everything. We'll click on all. Yeah. So now I don't have any triple cons. Instead I have only single cons. That too, due to this particular surface missing. So there is a surface missing. That is why this single con is present over there.

Now we'll try creating a new surface. We'll see how the new surface will become if we use new with cons with loop option. So loop option enabled everything like the selection is proper. But we are not sure whether the surface will come proper or not. So we'll check that. As expected, surface is not coming proper. You can see the preview. Yeah. So as we have seen, the cons option is not working well if we are choosing with the help of loop. So basically now what we should do, we should patch this surface by creating so many surfaces.

For that you should apply some indirect methods. So how? Basically you can project the hot points. So click on project. Once you click on the project, you can able to see the hot points are present over here, right? So you can basically, I think you can directly use the multiple project hot points button. So you can use that. You can pick all this hot points from this particular features like this and then do middle click. And then project it to this particular top side single con.

Okay. So click that corner and do middle click. You can see all those part points are now projected at the top. Once you are done with this, you can basically start creating a new surface one by one. So we will create surface one by one, set to very small small surface by having this cons as a reference. So click on new, go to cons and then try picking this. So understand, we are creating very small small surfaces. Be very careful about selecting your cons. So you have filled your this many features surface from here to the top.

Now you are left with only rectangular shape of surfaces everywhere. So now it is very easy to use Koons option and with the help of Loop, you can basically create a new surface. So that can also be done and now I will also explain you about new tool which is nothing but fill hole. So you can always use fill hole and then select the con which is selecting your hole which will also show you the preview of your hole. If you want to see the preview very carefully, you can basically turn off all your single, double, triple cons.

Also, the cross edge and then check your selection by turning off your shadow. So this is your selection. Selection seems correct. Do middle click and it will fill for you. Similarly, select the other hole. So now in this view, you will not be able to select the cons because cons were hidden from the bottom. So only enable this single cons, select the whole, check the preview and then create a new surface. After that, you can enable everything and then check if you are missing with anything over there or not.

Basically, no. Everything is done perfect. So this is how you can basically create a new surface either fully or patch by patch. So with this, we are finishing with the topo cleanup for the stop region. We will check if we have any other topo cleanup required over here or not. So basically, we can check that by doing control and shift. So we will able to see the single cons in the wireframe mode. And then we consider that that surface are left to create or something is not good over there.

Okay, so this is very easy way to check your single cons and then solve that out. Now, as we have seen that, we will try to figure it out what is happening over there and what can be done. For that, what I will do, I will try to hide the unnecessary surface which I don't want now as of now. So I will hide the top surface. Also this. I will hide my bottom surfaces as well. So this is what I left with. So this single cons was showing to me.

Also, I will use plus option and get these things back. Okay, so this is how we can check if everything is correct or not by isolating only the required area of interest. So here we can see this surface is penetrating with this slant surface. So just try to visualize this particular surface is a vertical surface and this particular surface is slant surface. So you can say this both the surfaces are extended up to a mark and then it's penetrating with each other. Right, so also this top surface is not needed now.

I will also hide that. So you can see this many surfaces which are sufficient to realize the case. Ideally, if there are three or more than three surfaces joining at a location, then you should expect a triple con there. But there is no triple cons. So you can consider that these surfaces are not joined but penetrated within each other. Right. So now we will learn a new tool which is nothing but intersect. Intersect in faces is used to intersect the faces. Once we do intersect, we can basically trim the excess part.

Let's see how it can be used. So if we click on the intersect, it will ask us to select the first group of surface and the second group of surface. So first, we will select the first group of surface. So let us select this as your first group, which is shown as purple color. Middle click, which will ask us to select the second group of surfaces. I will select this, but not only this, but also this as well. I will select this group as my second surface, which is denoted with blue color.

So now I am pretty much fine with my selection. I will do middle click. Here we go. So they are showing us the intersected part. And now it is our job to delete the unnecessary surfaces. So earlier we were discussing that we were expecting triple con over there. So now we are having a triple cons. That means the surfaces are connected. So triple cons will be solved if we are deleting this excess surface and this excess surface. Let's see how it's happening. So go to delete.

Select this surface. Select this and this surface. Check with the selection every time. Middle click and then get rid of that. So here we can see there is no single cons or there is no triple cons present. In fact, everything is coming very perfect. Here we can see some glitching is happening. So again, our left surface is present there. So we can see that two cross hatches. Ideally, the top surface should have brown color, but it is showing the orange color. So we will figure out the orange color cross hatch and we will delete by putting that orange color cross hatch.

We will select this and we will delete this. You can see everything is fine now. Still, you are able to see the triple con, right? So don't be afraid of that. Instead, just check whether there are another surface present or not. So basically, no. So control Z. For this kind of thing, what you can do, even though it's showing the triple con, basically there will not be any triple cons. Just like we deleted one surface, but that changes is not happening yet. So what you can do, we can manually release the con like this way and also check the selection.

So this is how we can select and then we will release the con. So by using the release option, we can basically release the con. Release in the sense, if we have double cons, it will be separated with each other. So there will be two single cons present over there out of your double cons. And if there is a triple con, there will be three single cons separated if we use release option. So now as we have released this, we'll also try to delete this unnecessary hot points if you don't want.

So we'll click on that. We'll try to get rid of that. So here it will not get deleted because this hot point is associated with this double con. But here there is no double cons present. So we can basically delete that very well. Here also there is a double con. So this hot point will never going to be deleted. So this is how we can release and once after we release, we'll again do topo like this. And we can see that triple con is gone and it was showing us only for the temporary period.

Now as we have released and done topo, that triple con is now converted into double cons. So now you may wonder what is this topo. The topo is basically opposite to this release. So what release will do, out of double con, it will create two single cons and out of triple con, it will create three single cons. Topo will do the same in an opposite manner. So if you have three single cons, if you use topo, it will try to connect all the three single cons and it will make a triple con over there.

Similarly, if you have two single cons present very near to each other and if you're using topo there, it will try to paste both thick single cons together. If there are two single cons, eventually it will create double con over there, just like this. The takeaway is, if you find any triple con and if you see there is no overlapped surface, you can basically use release and then do topo again just to ensure that there is no triple cons available. So you can basically solve the triple cons by releasing and doing topo again.

So this is all for this particular reason. We will click on all again. Now we can also see there is a surface missing over here. Now this part is a bit tricky because this surface is not a flat surface but a covered surface. Right, so I hope you can imagine this. So this surface is inner side surface and this surface is outside surface. So outside casing we have still here, but from here to here it's opened. So we should not have it open. So we'll figure it out how we can close this.

I'll show you a few possibilities. So first we'll go with the simple possibility which is nothing but feel-all option. We'll consider this as hole. We'll try to patch that out by selecting this way and then doing middle click. You can see the surface is getting created, but it's not coming in a proper manner. It's going inside over this inner surface. Right, so we'll do CTRL-Z here. So fill hole is failing over here. So that approach is not correct. The another approach is, so I will show you different different approaches. You just consider which approach is correct.

So now I'll go with the new option with the Koons. I'll go with the loop option. We'll select everything. We'll do middle click. You can see the preview. The preview is not like this manner, but it's in a flat manner. So again, this is not correct. Also, I don't have any alternative for that. So I'll cancel this. I'll go with fitted with loop. Select this. Middle click. So again, my preview is worst. So I will not go with this. Also, alternative is even worst. So I'll close this. I consider that the new option is also failing over here. So you may wonder how to create this surface now.

So again, if you don't have any other possibilities to create a new surface, just like the top case over here, as I told earlier also, we should think of creating surface one by one. Like we can finish this patch by using so many small, small surfaces. In order to create small, small surfaces, you should have a few hot points present over here in this location. So just understand what I'm doing here and you will understand what can be done on this particular case. So I'll create a new hot points. So in order to create new hot points, I will use some new tool.

So click on a parametrical option, write 0.5, not only 0.5, but also we need to assign some direction also. So I want my hot point to come over here in this direction, right? So I will select a con over here so that my arrow will start from here and it will go in this direction. Why? It will go in only this direction because I have clicked somewhere over here. So ANSA, consider that my point will start from here. If it's supposed to go in this direction, I should suppose to click over here.

So I clicked over here and it showed me this arrow direction. That means from here, ANSA will consider a line starting from this point and it will go in this point. ANSA will also consider this length as 1 mm length and it will ask us to write at how much mm length you want your point. If this line is 1 mm, basically I want my point to be it at 0.5 mm. I'll write 0.5 and I'll click on OK. And you can see there is a hot point coming up over here.

Same way, I will also do the same thing again by clicking again over here. This time my length will be 1 mm starting from here and ending till here. So this is now my new line. So again write 0.5, click on OK. So new hot point will come over here. Again do the same. So use parametrical option like this direction. Click on OK. So it created a point over here. Similarly, how I created two points over here. I will create a point over here as well.

I will create a point here as well. Here. And finally here. Like this way, at equal distance, I have created 1, 2, 3, 4, 5, 6, 7. So I have created 7 new hot points. And then I will do the same on the other side, over here. So now you are aware of what I am doing. So you can also try the same. 0.5, it's creating over here. Again do the same. It's creating here. You may wonder why I am creating this many points, right? So I will also explain you that in the latest stage.

Click on OK now. So now I have every hot points present over there. So you may wonder why your, this particular hot points are not getting visible. Even though it's turned on over here in the database. So if you want to see those, if you click on insert, everything will come up again, right? So it's just like it's not showing over here. But it's already there, present in our model. So now we'll start creating the new surface by using the same foons option. This time we'll not use this loop option.

Instead, we'll go with entity mode. We'll select the surface, this, this, and then check the alternate. Alternate is this. So now you can see my alternate is not touching to my particular existing surface. So this is pretty much fine. Click on OK and I'll have it. Similarly, I'll do with the bottom surface. I'm doing very symmetry on both the sides. And I will select the second set of motion on the top. Alternative, C. So if I zoom in, you can see my surface preview is not interfering to my parent geometry, which is already present there.

So I'll create a new surface and still it's not sticking over here. So I'll do the same for the bottom side. You know, it's a bit lengthy process, but it's a foolproof method where you will not find any kind of problem in your new surface or this kind of cases. Always check with the alternative and then create a new surface. This is how I create it. This is my last surface. It is closed by all the single cons. So I'll go with a different tool, fill hole, select this and we'll create this finally.

This is how I made this surface. So now coming back to the question, why I created so many hot points? So I created so many hot points just to create a very smooth surface over here. You can see this existing surface is so smooth, right? So I should have the same smooth surface or same smooth curved surface present over here. Then only my intersection will not happen with my already existing surface.

Part 2

Hello guys, welcome back. So in the previous class, we did some topo cleanup, we removed some overlapped surface, and we solved triple cons as well as single cons by deleting and creating new surfaces. So now we will again check if we have any errors left in our model, and then if no, then we will start with PID assignment, and then we will go with the volume trig match. So now we will check if we are remaining with any single cons or triple cons in our model.

So in order to check that, so as I have discussed earlier, we will check by hiding the respective lines. So now I will first check my single cons, if I have any single cons in my model or not. So I will turn off each and every cons except single cons, and I will also turn off my crosshatch, turn off my shadow mode. And we will see only the wireframe mode. In the wireframe mode, I can see there is a single cons present over here. So I will again enable this shadow mode, and we will try to figure it out where the single cons is present.

So this is one way which I can do for checking my single cons, and the other way is, I can directly go to the geometry checks, and then there I will check my geometry. So I can go to the text, in that I can go to geometry checks. Here I basically check with single cons, and I will execute. So I received a lot of triple cons as well as some single cons. I will select the single cons like this way, and it will show me the preview.

So it is the same location, where I had single cons in the wireframe mode. I can see that the single cons is present at the shaft location. So now I will try to isolate this, so I will click on show only, and it will show me this particular single cons with its neighbor surface. I will minimize this. So just make sure, if you want to minimize this pop-up box, you can basically do middle click over here in the heading. So if you do middle click, it will be done.

If you do again middle click, it will be opened. This is a very cool shortcut, which you can use. So here you can see, the neighbor surface is coming up over here. So I will click on add. See, so add is not working. So the reason is, here there is a single cons, so add will not work over here, because single cons is not attached with any other surface. If I add over here, then basically, it may work. So it's stating a surface over here. Also, if you check with your first label, it will not show you anything, because your geometry is ending over here.

So now, as I have the single cons, I should also have its neighbor surface in order to either perform topo or perform page stops. So I will click on all now. We will try hiding the unnecessary end piece from my screen. So, what I will do now, I will open my PID manager, and then I will hide one by one of my components. By checking the colors, I will hide that particular PID. So, like this way, we can always check the single cons, so the single cons is present over here.

So now, I think I should try with topo, so I will apply topo over here, and you can see there is a triple cons forming over there. So, once we have triple cons, understand that there should be some overlapped surface. So, we will check that as well. So, checking that, I will click on all, and then I will also perform my text manager again. So, I will go to back. Visible is already turned on. Then I will rerun this by clicking on execute. Let's see if I have any single cons present now.

No, there is no single cons present in my screen, but I have a lot of triple cons. So, now I will think of following my triple cons. So, first triple cons I found over here in this location, and then few triple cons over here in this location, and one triple con over here. So, we will start one by one. We will start rectifying this triple con. So, let's start with this. So, here you may find, like the triple con here, so just understand that triple con is not always an error.

It can be a warning. So, we should basically go there, and then we should check whether the triple con is necessary or not, or the triple con is formed due to any valid results or not. So, we will check that. In order to check that, what we can do, we can try isolating the surfaces which are connected with that particular triple cons. To examine whether the reason is valid or not. So, in order to isolate those, we will use I not option and we will select the entities like this.

And then, do middle click to isolate this. Right. So, we can see there is a triple con form over there by having three surfaces joined together. If I show you the surfaces, this gray color is surface number one. This green color is surface number two. And, again, another gray color, surface number three. There are three surfaces joining with each other, and that is the reason why it is creating triple cons there. So, don't consider this as an error. Instead, you can check whether you can do anything over here or not.

So, basically, no, you don't have to do anything over here because you are not allowed to delete any one of the surfaces. If you delete those, basically, it will be single cons there and there will be one. Right. So, yeah, here there was another surface. I will do control Z. Give me everything. Now, I will try isolating my each and every PID and we will examine that. I will use PID and I will examine this. So, this has triple con, now I will use plus command, that is, and command, and then I will see.

I can lock this, then try checking further. Okay, so you can see there is a page which is shared by this entity and this entity over here in this location. So, as I told, we don't have to worry much about this particular triple con. So, this is allowed. So, only one triple con is present over here in this location. So, we will click on all. So, nothing is coming up because we have given a lock. So, we will open a lock and then we will click on all and it will show us for us.

So, it will show everything. Now, we will check with another triple cons. So, here you can find there are triple cons present here. Even though, here also you may find a triple con if you do top over here. So, we will check that. So, we will check everything and then we will do topo. Yeah, so there is a triple con now. So, which means this shaft is having some triple cons. So, we will hide this outer PID. This, this. Yeah, so this is fine. We can play with this many components from the screen.

So, we will lock this. And then we will check what we can do here. So, again you can see some glitches present over here, right? So, that glitches also shows that there are overlapped surfaces present over there. So, starting with this triple con, consider that there should be some overlapped surface present over there. We will figure that out. So, now we will hide each and every surface and then we will see. So, first of all I will hide this surface. In order to do that, I will click on this crosshatch.

Also, I will click on this crosshatch. Right? So, you can see there are two sets of crosshatch presence. That means there will be two surfaces. If I try hiding one, there will be another surface. Right? That means two surfaces are overlapped. So, I will click on all. I will hide again this. And then we will try removing this, both the overlapped surface. So, I will use delete option now. We will select this. You can see the green color. So, the crosshatch is now converted as green color.

Delete that. Again, there is one more surface. I will delete that as well. Once I delete both of them, I will click on all. And you can see there is a double con present over there. Also, these two volumes, which were separated by two surfaces, are now. You can see there is a double con present over there. You can see there is a double con present over there. You can see there is a double con present over there. Thank you. Converted as a one single volume because you deleted both these surfaces which were interfering between these two volumes.

So as I have deleted two overlapped surfaces over there, it created a single volume. So I will do the same thing for each and every triple cons just to create this as a single volume. So my objective is to create this as a single volume. This is pretty much useful if you are planning to do volumetric mesh. So all this, why we are converting this as one volume, you will understand at the later stages. So for now, just understand, we want to convert this as a single volume so that we should delete all these unnecessary surfaces that are overlapped with this.

Like this way. You can see, one by one, these triple cons are converted as triple cons. So setting a view is much important here. So only if you set a view very better, you will be able to select the surface very nicely. Otherwise, surface may not be visible to you. Rotate your model very wisely in order to delete the unnecessary surface. Make sure you have a habit of selecting the surface by clicking on the crosshedge only. Same way, for deleting the surface, you can only click on the crosshedge.

If you want to delete both the surfaces together at the same time, you can select this crosshedge. Also, you can select another crosshedge. So that both the surface will be selected together and then you can delete at the same time. This is pretty much very useful. For this particular thing, that should be something we should check. First of all, let's try hiding this surface and try deleting this surface, selecting everything. This is fine. Both the crosshatches are selected. And if I delete this, you can see there is a triple cone present over there because there is a Olapped surface.

So this is what we should figure it out over here. Understand that each and every, these blades are having in the same PID. Okay, so all these upper blades are in one PID. Same way, this middle blade should also be in one PID. That means the crosshedge you can see over here that is combining of this pink color and then this brown color PIDs. But we want only brown color PID over here, not pink color. So our task is to delete the pink color PID till here.

So we'll try selecting the surface over here and then we'll see what kind of surface it's showing to us. So in order to isolate, I will use all option and then I will click on this particular pink color crosshedge over here. You can see it's selecting entirely. So just understand that the pink color surface is starting from here and it's ending over here. So it don't, it don't have any cut over here. Right, so if I click on all, we can consider that the pink color surface is starting from here and it's ending till here.

In order to cut this much pink color surface, we should have a cut present over there. Now that cut is not present. Similarly, if I isolate this particular brown color PIDs, you can see the brown color PIDs also having length till here. Till here, that means this much area is overlapped with brown color and pink color surfaces. But we want only brown color surface over here in this region, not pink color surface. For that, we should have a cut over here so that we can delete this much smaller pink color surface.

In order to separate this much smaller surface, what we can do is we can do project in the cons. Once we can try selecting this cons like this way, do middle click and then project on this particular surface. Once we project that, you can see the projection has happened, but it's not in a good manner. So what we can do here, we can use the fine option. So go to fine in the auxiliaries and then click multiple times over here in this particular region. What it will do, it will try to find your cons.

Like this, you can improve your cons resolution. This is how you can use your project option. Once you have projected the con over there, you can basically check the same by isolating this particular PID this time. So I will isolate this. You can see there is a projected con coming up over here. Now it's a good time to delete this separated surface. Earlier, if you try to do so, basically it will try deleting all the surface because there was no separation happened. But now as we have used project option in the cons and projected the existing con over here in this pink color surface, now we can very well try deleting this.

Here we have deleted. Now we will click on all. You can see there is a single con and there is a double con present over there. In order to rectify this, what I will do, I will first release my con over here, like this way. I will release the con and then I will do topo for the same. You can see there is a triple con present. So understand, again there should be some overlap surface present over there. So I will try hiding this surface and we will see, yeah, so there is a surface inside that.

So I will try deleting this as well. And then we will click on all. You can see there is a double con over here. So things was a little bit tricky, but I hope you understand what I did. So what I did, I tried taking this double con from this brown color surface and then that double con I projected on this pink color surface. Once I projected con, I can delete this pink color extra excess surface so that it can solve that overlap surface. So let us confirm if we are missing any triple con or not.

Basically no, everything is, seems fine. Try checking this triple con. So again we have a triple con here, do the same way, hide this and then try deleting this surface. Before that, what we will do here, instead of PID, we will try selecting the entity. I will write this entity and then I will try to delete two surfaces over here, but you can see there is only one cross present over here. That means another surface is not separated yet. We will see what to do with that.

First of all, I will try deleting this surface. I deleted that. I will delete it. I will press escape in order to remove this I not operation and then I will click on delete. Then I will delete this surface. Once I delete this, you can see there is no crosshatch is present. Yeah, that is a crosshatch, but that is for all this surface together. If I can show it to you. If I am selecting this, it is selecting everything. That means some kind of connection should be closed over here so that it will not select whole surface for me and it will select only this much circular surface for me.

Right. So how can I do that? Basically, in order to do that, there are two multiple, there are various approaches for that. So I will show you two approach out of those. So first approach is just to hide the surface and then use cut option and then make a cut from here to here, here to here, here to here. Similarly, we can try using the cut option and then make it close so that the surface will be separated from the existing surface. You can see there is a crosshatch coming up here and if I click on delete and then delete this, it will delete it only this much surface, not all the surface.

If I click on all, so I can again try topo in order to solve this single cons. I will try that. Right. So except this location, I got topo everywhere else. In this kind of location, I can basically use paste option, pick the single con, pick the single con as well and then do middle click and it will form a double con for you. This is one of the approach which you can try in order to cut that and then delete that. I will also show you another approach for that.

So this was the earlier case. Now what I will do, I will call this in this surface. Now I will try projecting my this pink color con to this. So please. Now let's stay. But I will have blue color surface. So I will use project in the cons. I will use loop option. Okay. Selecting partially. So what I will do here before that I will hide my surface. I will hide my this PID. Then I will select all my cons from this location in order to project that. Click on project. Selecting partially only. I will select like this way.

I will deselect this. Deselect this. Like this I have selected this for projecting my cons. So I will do middle click. It will ask me to select a face. This time the face will be my this blue color surface. I'll hide this. And sorry. This can be my face. Okay. We'll keep like this and we'll try projecting that over here. Once we project that basically all all this cut happened by itself because we projected that and then now we can very well go. These are the two approaches which you can basically perform. And then you can also do topo in order to solve your single cons.

Right. So there are two approaches. So whatever approach you find it correct and find it easy you can very well go ahead and then do that the same. So in order to ensure that there is no single cons and there is no triple cons present in this particular components. We'll perform the geometric check over here for this much visible entity. Make sure the single cons and the triple cons is turned on and I'll execute this. Everything seems fine to me and it's showing me status is OK.

So I'm OK with this. I'll click on all. I'll release the lock and then I'll click on all. So this is how I solved my possible triple cons which was not expected there. Now we'll check another triple cons if we have any. So we'll again check the geometry checks. I'm going to execute. Still we have two triple cons. We'll see. Yeah. So these triple cons are basically this. So as we discussed this is required and we should not remove this. That means we are finishing with our topo cleanup now. Now it's our task to see and close the geometry so that we can do volumetric mesh.

In order to close the geometry first of all we should check where the geometry is open. So basically the geometry should be closed enough in order to perform the volumetric mesh. If it is not closed it will throw you an error. The geometry seems close to me. We'll figure out now how we can assign the PID for the different different components. OK. So we'll open the PID manager and we can see PID is almost created. It's just like we need to get the name. So before that we just confirm whether the PID is correct or not.

So yeah. It's showing me this many surface. I can also click on show only and then examine my component. If this component is not having any unwanted surfaces present in my screen. And also I will check whether it is closed or not. Typically this geometry is closed enough and very well ready with the volumetric mesh. So just like this we'll check each and every PIDs one by one and simultaneously we'll also define the name over here. So this can be our casing. This is fine. Also error proof.

We'll check with the other. Before this I click on all. And I will check this casing now. Probably 15 number PID. So I will click on show only. This I will examine now. It seems close to me. Yeah. It seems close to me but here it's open. So we should basically think of closing this. We'll see if we have any surface over here. No. So the surface is not present here. So we should not have this. We should basically close this. So just remember we need to create a surface over here in order to close this.

And then this surface we can consider as a closed surface. So let us create a new surface over here. By clicking on new. Fill this surface by selecting the single, sorry double cons. Take the selection and then make it close. Click on OK. This is closed now. Similarly if you can see there's a green color PID which we saw which is nothing but your outer casing. That is closed but again this inlet and outlet is also open. So we should also think of closing those. So let us create a new surface there.

Make sure we are selecting this cone over here. Not this cone but this cone in order to close this. We'll close this like this way. Also we'll close this surface as well. There is also open timber over here. You can see the backside blades available right. So this is also open. So we should also think of closing this. We shall try closing this by picking this many. I will show you the selection of the cones. You can see the selection is like this much. So I will suggest you to check every time your selection so that this kind of error you can get.

So here I have missed selecting this particular cone. So I can also select that particular cone while being there in the wireframe mode by double clicking on that particular cone. Like this way. So as I have selected this I will do middle click. I will click on OK. Same way I will fill this particular surface from each and every region. Make sure I am conforming every time before making any surface there. Also I am taking the preview. If the preview is correct only then only I will create a surface.

So just like this I have patched my surface from the top. And I made this turbocharger very well closed here. Also I should have closed this particular chamber from this location like this way. I think everything is closed here and we can basically start getting PIDs again. So before assigning PIDs for the different different location I would also like to create new PIDs. Inlet, casing inlet, outlet. Similarly, thumb casing inlet, water casing outlet. Now as we have created these four different different PIDs. Now we will basically assign those.

So casing inlet, right? So this is my casing and this can be the inlet of my casing. So I will assign this PID by right click. Click on apply. Select this. Do middle click. It will assign for us. The same thing for casing outlet. So right click. Click on apply. Select this and middle click. Also, you can assign over here as well. I am just giving it very randomly. You can give as per your requirement. So this is how you can basically assign your PIDs. Go ahead and tell us.

Give you time to ask us your moving place. Don't know. I will also assign this PID for this modern casing now. So I think this is 15th number. So if I want to check which PID number is this, I can basically use peak options like this and it will show me 15th number. So I will change the name here. The name should be. So the name can be anything. So you can give your name. You can give the name of the components as per your requirement. So whatever PIDs I have assigned, I will basically try hiring those.

I will hide the outer casing PID. Casing inlet, casing outlet. Bottom casing inlet. Showing me that bottom casing outlet is not yet defined. We will check with that as well. Click on add and check that. So probably this is my 22 number and this is also 22 number. So basically it should be 23. So I will right click here. Click on apply and then we will apply this over here. So these two are also assigned now. Also I have assigned this bottom casing PID. Now whatever PIDs are left, I can basically think of assigning those.

So testing. This must be 16. This must be 16. This is also assigned. And hide this here. So here we can basically check that there are 1, 2, 3, 4, and 5 different PIDs are present over there. Same 5 PIDs we can also find it over here. So we will just write the name of that. So we will just write the name of that with respect to PIDs. So we will check this PIDs. So this is one number. So we will change the name accordingly. So just understand this is just demonstration purpose. So I don't think these names are very correct. So just to demonstrate to you, I am just giving random names.

So here you can see that this and this are of different PIDs. But I want both of them in a 1 PID itself. So what should I do for that? So you can see this pink color is already assigned as this 13 number. So we can write shaft over here. We want this orange PID also to be updated in the shaft category. So what I will do, I will right click over here. We will click on apply. I will apply PID wise. I will select this by PID mode and then we will apply over there.

So you can see that is also updated in my shaft PID. Also, a notable thing is the previous PID which we checked seems no more now. So we can also check show only. Nothing is coming up, right? So we can basically try deleting this. It is showing that we have deleted some surface for that particular PID so it cannot be deleted. So if this is the case, basically first of all, I will click on all and we will see. If everything is coming up or not. If everything is coming up or not. So click on fit in and everything will come here. So this PID number 9 and 11, we will try to explore what are these. So basically it goes on nothing, right?

So now here we will forcefully delete this. So make sure in order to forcefully delete anything, you can basically use compress option like this way. If we use those, basically those two things will be deleted now. So now we are left with only this many PIDs and all these PIDs are pretty much correct. We will check each and every PID one by one. If it is closed or not. If it is closed, then basically we will go with the volumetric mesh. Before volumetric mesh, you should always go with the surface mesh. So surface mesh is the prerequisites of the volumetric mesh.

I will go PID by PID. Seems closed. Seems closed if we have another PID. As this is done, we will try to start a mesh for this particular PIDs. Make sure we can also give different different mesh length to the different different PIDs as per the size of that particular PIDs, which is nothing but the size of the components. And then we can think of starting the volumetric mesh for this particular components. So this is all for this class. In the next class, we will see how to assign the mesh quality criterias for these different components and then how to mesh that before going with the 3D mesh, which is nothing but volumetric mesh.

So we will meet in the next class. Thank you.

Part 3

Hello, guys. Welcome back. So, in the previous class, we gave some PIDs and then we did some geometrical cleanups and then we closed our particular model such that we can define the volumes. So, in order to give a proper PID, so we have already given a PID, so we'll just try changing the names now. So, as you guys are aware of how to change the name. So, we'll see one by one. And, we'll see each and every component one by one and we'll try changing them. So, first of all, we'll start with this particular outer casing. So, you can see here, so this is outer casing.

So, basically, this PID we can give as, we can give the name over here as compressor casing. Similarly, for this particular casing, Alright, so here, we can pick this and we can change the name over here as turbo casing. This bottom feature, we can rename it as, this feature, we can change the name as inlet casing. So, we'll hide all this. Going back to this plates, so, the top plate, we can tell as, blade, stage 1, middle plates, call it out as stage 2 and bottom plates, which is nothing but our impeller.

This shaft is nothing but shaft rotor. We'll also hide this. Now, after hiding this, we are left with only this particular inlet and outlet surfaces. So, this is fine. So, we have renamed all this. Also, in the previous class, we forgot to delete some simple cons. So, if you can check over here in this top region, let me hide this surface first. Let me hide this particular casing first and then we'll see the shaft. Over here, you can find there is a surface over here. So, we'll try hiding the surface and we'll see if we have any surface.

Yeah, so, we have a surface here. So, basically, we can delete both the surface one by one this way. Understand that if you don't have a cow over here, you can always take this double cone. You can always take this double cone and then project it to this particular surface and then you can delete that inside surface over there. Make sure you don't have any surface inside which is unnecessary and which will create two volumes over there. I'll always suggest you guys to hide any one of the surface and check the continuity of your particular volumes.

So, just like this, you can hide each and every surface and then you can try checking the connectivity or let's say the volume if it is common or not. So, I'll hide this particular last blade over here. I'll hide the surface from here at the bottom of your impeller and then this particular top surface and we'll try to see throughout. So, I can able to see the throughout, right? So, I can also see the background of my ANSA window. So, that means I have the common volume over here. So, throughout shaft is having a common volume there. So, which is also good.

Also, we forgot to delete some overlap surface. So, here, if we hide this surface, you can see there is an overlap surface present over here showing the glitchings. So, again, you can see the glitchings of two color. One is the pink color and one is the green color. So, we don't want green color surface over here. So, at this particular location, I will suggest you to delete the green color surface by picking the green color hot points. Sorry, the green color cross hatches. So, by picking the green color cross hatches, you can basically delete those on all.

So, do the same way over here. So, I'll hide my top surface and you can able to see the overlap surface is present over here also. So, this kind of overlap surface may cause an error while going in the volumetric match. So, once we go to the volumetric match, we may find some error called penetration. So, that error is basically showing us the overlapped surfaces. So, here, in this case also, we will try to delete the gray color surface by enabling this delete in your select option and then clicking on the gray color surface.

Same way, we will find the gray color cross hatch over here as well. Once it is done, we can again click on all. So, this is pretty much fine. We will see if we are missing anything. So, I think we are not missing anything. We will start matching now. And if some error is happening at the later stage, we will basically try to figure that out. So, you can always check your model by turning on your wireframe mode. So, as we discussed earlier also, you can always turn on your single count only.

Turn off everything and also turn off your shadow mode and just try to figure it out if you have any single cons present. So, I cannot see any single cons present. That means everything is correct. Also, check your triple cons by turning off your single and double cons and turning off your shadow mode. So, this many triple cons are basically accepted. You can have only this many triple cons. So, this is pretty much fine. Everything looks perfect over here. So, I will again turn on everything and we will try matching this.

Before matching this, I would like to tell you few things about volumetric mesh. So, volumetric match is nothing but 3D elements kind of mesh. So, till now, you have seen the surface mesh which is nothing but mesh with with the help of 2D elements which are dry elements. Now, in this particular week, we will try to figure out what is volumetric mesh and what are the steps for achieving that particular volumetric mesh. So, volumetric mesh is nothing but a surface mesh with dry elements and that too. After we do surface mesh, we will try defining the volumes and then we will try expanding our 2D elements and convert it into 3D elements. So, we will see how it will work.

So, just understand that the very prerequisites of this volumetric mesh is nothing but surface mesh first. So, only if you are doing surface mesh, you will be able to do volumetric mesh. So, before starting with the surface mesh, I would also like to check my geometry now. So, I will go to the checks and then in the checks, I will go to the geometry and I will check for my single cons. Even though I have checked by turning off the double cons and triple cons at the bottom.

But again, I will go over here and then we will try checking my single cons over here. So, basically, no single cons are present and the triple cons are present. So, I will do control A. I will try to see my triple cons. So, triple cons are the expected location. So, we don't have to much worry about that. So, we will now start with the mesh. Before starting with the mesh, as I told, you can always give your quality criteria, mesh parameters and length options every time. So, starting with quality criteria. So, here is the interesting thing. So, here we will not be giving a common quality criteria for each and every model. Instead, we will give quality criteria for different models. So, as we have given different PIDs for different models, we will go one by one and we will give quality criteria and we will again start doing the mesh for that particular ID. So, let us start with the biggest ID which is nothing but our compressor casing and then these two outlets and in waves.

So, we will isolate those. We will see what are the PIDs we want. We want this PID, this PID and this PID to be visible. So, I will select this. So that it will be highlighted over here in my PID Manager. I will right click and we will do show only. So I will also suggest you to note down your particular target length for your different parts. So this is what the target element length for your particular PIDs. I will suggest you to take a screenshot of this or take an image of this and then apply the same mesh length or target mesh length with different different PIDs over here.

So we have given the names over here and the same names we will be isolating the models and then we will give the respective quality criteria which is nothing but target length over here. So as you can see here we have isolated this particular compressor casing which is supposed to be matched by 5mm mesh length. So now we will give 5mm everywhere. So as I will be giving 5mm my minimum length can be 3 and maximum can be 7. Click on OK. Match parameters can be 5 over here and again 3 and 7 over here. Here the match element type can be trial. So don't forget to change this type of your element otherwise you will come up with mixed elements because mixed elements are the by default elements which is given in the match parameters while you open the answer.

You can always save your quality criteria over here in the particular save mesh parameters file. So you can use this icon in order to save the file and then again open the saved file over here and then you will have this kind of settings enabled in your screen. So you can basically save your settings and then open the settings over here by using this read option. So as we have given this 5mm over here in mesh and quality will now give the mesh length over here in the particular mesh stack the length option.

So queue perimeter as 5 also macros as 5. So as we have given all these quality criteria as well. Now we will start with the matching. So instead of doing one by one I would like to go together for each and every components. So what I will do I will go with spot mesh and then we will do visible. It will take some time to mesh that and it will give you the mesh over there. So you can see my all the components are now matched with the given quality criteria.

Not only the surface but also inside the surface also you will have some kind of match present over there. So I will use this not option. We will try hiding the outer surface and you can see the inside surface is also matched. So this is how you can also check if all the surfaces are matched or not. So basically if you are using spot mesh visible option it will give you mesh throughout your visible models. Right. So this is very nice too. So you can again use this AND option to retrieve your hidden surface back.

This is how you finished with one component. So I will suggest you to go by each and every components and then finish each and every surface mesh by isolating those components. So as we have finished with this we will again click on all. Now this time we will try going with the other which is nothing but our turbo casing which is also has 5mm. So this time what I will do I will take all these 5mm things together and then we will match that in one shot.

So I can see that the turbo casing and the inlet casing cover both are having 5mm match length. So now I will try selecting turbo casing and then inlet casing cover both of them together. I will hit them right click and then show only you can see. So this is what you have. So you are supposed to match it with 5mm. As I have already given the match parameters and the quality criteria as 5mm over here. Also the match length is also 5mm. If you want to check you can also check that on 5mm I will give 5 over here and also I will give 5 over here.

So you should basically check every time this match length should be 5. Once it is done you can basically go with spot mesh visible and have this match. You can click on all. Now you are finishing with this many things. Also you are left with these 2 closures. So I will take that as well. So I will select this one. So I will select this one. So first of all I will select everything from here. I will select this. Not that. But my inlet. And then this outlet.

So these two. So I will isolate them only. Then spot mesh visible. So I did not check with length options. So I will check now. I have 5. That is 5. Macros also should be 5. Which is also 5. This is fine. Now I have finished with all this. Now we will go with inside components. Which are nothing but shaft and the impeller and the blades. Right. So now we will isolate the inside parts. We will hide the mesh surfaces. By selecting all this. By using pick option.

And then I will click on the bulb. Any one of the bulb. It will try to turn off all the bulbs for the selected analytics. This is how I can do. So I left with this also. I will take this. By. So these are the things which are left now. So now I would like to go with the impeller first. You will see the quality criteria of an impeller. So that is 2 mm here. So now what I will do. I will go to match parameters or quality criteria first.

My target length is 2 mm. Minim can be 1 and maximum can be 3 mm. Match parameters. Here I can give target length as 2. This can be 1 and this can be 3. Click on OK. So match length. I will try choosing. So this macros can be 2. Similarly. Here it will be much more difficult. So I will set a view like this. I will make a box selection like this. I will make sure I have not selected the unwanted lines. So I will deselect by doing right click with shift.

So I will check this. It will look like I have given this parameters correctly. So middle click and I will give match length as 2 mm. I will click on OK. Once I finish this. I will start giving match over here. So this time I will not use visible. Instead I will go with select. While clicking on select. One option list is coming up at the bottom every time. So you can also cross check. Whether this tria is given there. Or the mixed elements are given over there.

If you can find mixed elements there. You can basically change it to trias. So now as I have selected. The spot match select option. Now they are asking me. To select the face. Instead of entity. I will select my faces by using PID. Only this much. Selection will happen. If I select it with the help of PID. I will do middle click and. It will match for you. So this is what. I supposed to be matched. By 2 mm. Now I will go with. This particular blades.

So we will see. What is the length of this particular blades. So 1 mm and 1 mm. So now I will change my. Quality criteria. So if it is 1 mm. Minimum can be 0.5. And maximum can be 2 mm. Click on OK. Match parameters. So this can be 1. Minimum length can be 0.5. Maximum can be 2. Length. So here. I will try selecting. Like this way. Then we will reselect. Like this way. And at the end. I will. Confirm my. Selection by. Pressing control and shift.

Which is nothing but my. Wireframe mode. So this seems fine to me. The main thing. Which is highly Drawing. The main. The parameters can be again 1mm. Macros, I have this PID option, so I will select by PID. And I will check that. So this is also 1. So I can go with the Spot Mesh, select by using PID, select this PID, this PID, check the selection. Do middle click and wait for some time. So this particular blades I have matched with 1mm as the mesh length. And the impeller with 2mm as my mesh length. So you can find the difference over here. Right. So this is how you can match your components without isolating those.

So earlier we saw how we can isolate and then we can use Spot Mesh, Visible. And this time we saw how we can even mesh the assembly or set of components without going with Spot Mesh and Visible. Instead we can go with Spot Mesh and then select. We can select either by box selection or by PID region. So like this way I have selected this. Now I left with only this particular chapter. So I will see what is my match length. So again, that is 1mm for me. So I will not be going and changing from match parameters and quality criteria as I have 1mm there.

But I will ensure myself if my length of this macros are same or not. Select my selection. Selection seems correct to me. So macros can be 1mm. It was not. It was ranging between 1 and 5. So now I will give it to 1. Same way. Perimeters. I will be selecting very wisely. You can see here. I am pressing shift. Pressing the left mouse button and then dragging a box selection. And then I am going in wireframe mode and then checking my selection if everything is correct or not.

So everything is correct. The match length is any way as well. As the match length is given, I will go with the Spot Mesh. Select and then we will select this particular pin of PID by enabling PID selection. I will select this. It will get automatically selected throughout as we have chosen this PID for selection. And we will do a little click after checking the selection. And you can see it is meshing with 1mm mesh. So you can observe over here this PID and this PID are supposed to be meshed by 1mm mesh length.

So it is showing a kind of same kind of mesh element size. So here you can find that some mesh is erased. The surface which are in contact with this particular surface, that mesh is getting invisible. Or we can say it is getting erased. So it is our task to again give it a match over there. So we will cross-check the Ucala match length, which is nothing but 2mm. So follow the same procedure. Target length 2. Minimum length can be 1. Maximum can be 3. Quality criteria says minimum length 1. Maximum length can be 3.

And macros I will select first by PID. This can be 3. Sorry, this can be 2. This one is OK. Parameters can be box selected. Like this way and it is selected. It can be 2. Once it is given, you can see the match is again going from here. We will look into this. Before that, I will go with visible. Not visible with the select option. Select this PID and we will match this. And over here in this location, where two different match lengths are coming.

Basically, this problem is arising there. So now what I will do, I will give my mesh length. So the reason why it is happening, right? So the reason is, we are giving the mesh length. So mesh length, we are frequently changing by selecting this particular edge, which is also touching with this particular edge, which is a part of 2mm mesh length. And this is a part of 1mm mesh length, which is making a confusion over here. So we will try meshing this by 1mm now. So go to length, select this, select this.

It is already 1mm. The macros, macro is also, it is ranging between 1 to 2. So why it is ranging between 1 to 2, because it has also selected this particular circumference, which is also a part of our blue color entity, which is nothing but in color, right? So that is why we should not change that. If you change again, the mesh will go away from that. So we will directly mesh this now. So, spot mesh, select, try, yeah, before that, check your mesh parameters. I will change again, back to 1, 0.5, 2.

Quality criteria can be 0.5 and 2. Now I will go with spot mesh select, select this phase, and then we'll mesh this. So you can see, so there is a transition phase over here. So very near to this line, elements are still of 2mm, if you can find out the length of the particular element. So it is ranging between 2 to 1. And as we go far from there, sorry, it is ranging, it is converging to 1mm. So this is what is happening if anywhere your two different mesh lengths are meeting.

Right, so this is how you can mesh this. So we have matched almost everything. We will click on all, and we will see if you are missing any unmatched surfaces. Yeah, so the same thing happened over here and here. So here at the two locations, we had a triple cons, which is showing that our mesh length is changing very frequently. So as our mesh length is changing there, the mesh is getting removed from there. So we need to do the same thing here in both the cases.

First of all, I would like to show you something over here. So here you can see, there is a statistics of our particular elements. So shell elements are shell. So the shell is nothing but a heading. So as we are working with 2D mesh, it is showing the shell over here. Once we will go to the volumetric mesh, it will show us as a solid of volumes. So here the software is showing that the quartz elements are zero because we are matching with trier only. And the trier elements are nearly around 8,74,958.

And the unmatched surfaces are total 8. So if you want to see the unmatched surface, we can basically do right click. So only just to show unmatched the surface. So these are the unmatched surfaces due to your variation of your particular mesh length. So we will try to fix it now. So in order to fix this, we will do the same procedure which we have done. So basically, here and here we have target length as 5mm. So we will change the 5mm target length over here.

So 3 and 7 in the quality criteria. And 5mm in the mesh length. 3 and 7 here. As you are not changing anything here, things will be same. So I will again cross check this micro. So this is also ranging because here at the bottom, the common edge where your shaft is connecting there, there is some possibility that the length can be 1 also. That is why it's showing 1, 2, 5. So I will not be much further about that. So I will just cross check this perimeter if it's changing or not.

So those are not changing. So I can basically now start matching this. So I will go with the spot mesh. I will go with select. And then I will select. Now by entity. I will select this entity. I will select this entity as well. We will mesh. See, so here some transition phase is happening. So the mesh is varying from 1 to 5mm. Similarly, from 1 to 5mm. I will also mesh the inside surface, which is not meshed. Sorry. So I will go to not option.

We will change the selection to entity mode. We will hide this surface. See, so here we go. This surface as well. And we'll try to mesh this surface. So you can see again there is a overlap surface coming over here at the top level. Most of all, we should remove that. So we'll go to the topo mode. We'll use this delete option and delete this green color crosshatches. Now everything is perfect. I'll go back to the mesh mode and then try meshing this. So, spot mesh, select, select this, mesh it. Also, select this surface.

As I have selected this surface, you can see the selection. I will match this as well. I will click on all. And we'll see if I am missing with any particular unmatched surface or not. So earlier it was like showing some unmatched surface. But now there is no any unmatched surface even though I have pressed all. Right. So I have missed everything here. So our model is very well ready to go with the volumetric mesh. Before that, just a cross check over here in this location. So we'll use this not option with entity mode.

We'll hide this and we'll see if we have any overlap surface present or not. Basically, we don't have any overlap surface now. Click on all. So I want to also share you some other tool which is nothing but cut option in the macros. So here you can see some transition is happening, right? So you can always use this cut option with reconstruct and then you can make a cut over here. I'll show you how. So, enable this reconstruct option in the macros cut in the option list and here you can choose the parametric cut over here.

Now try creating a cut over here. So you can see some kind of changing is happening. So some kind of formulation is happening over here. So what I'm trying to do here, I'm trying to isolate this region where my mesh lengths are changing. So I'm just giving randomly a cut like this way. Then you can see there is only one surface over here which is having mesh length varying between 1 to 5. And apart from that, this region is totally almost 5 mm mesh length and this region is almost 1 mm mesh length region.

Like this, I can use cut option with reconstruct option enabled and then I can try creating cuts and isolate the surface near to this particular transition face, right? So this is how I can use cut option. Here also I can do the same. So I can create cut like this way. Also from here to here. So I can use any shape. So it's not like I can always use this particular I can use whatever shape I want. So the concern is So it's creating some other location.

So I can rotate my model and we'll try to create a cut from here to there. So the main concept over here is we are trying to create a separate region where we have this particular mesh length ranging from 1 and 5. So this is how we can make a cut. So this is all for your particular surface mesh. At the end, you are having this 9,16,442 elements which are nothing but tri-elements only. So now in the next class, we'll try to figure out how to convert this shell elements into solid elements while defining the different different volumes.

And what are the volumes we will be having? And what are the volumes we will be deleting by considering that those volumes are of no use. So all these things we'll discuss in the next class. By that time, if you are facing any difficulties, please consult your support engineers and get it fixed. So this is all for this class. We'll meet in the next class. Then, on the next class. How about the actual space of this?

Part 4

Hello guys, welcome back. So in the previous class we tried meshing the different PIDs with different mesh lengths and now we will go with the volumetric mesh now. So in order to start the volumetric mesh, we should go to the volumetric mesh deck. Before that, as I discussed earlier, the prerequisites for going with the volumetric mesh is to check whether we have done the mesh very correctly or not. So to check that, we should always check, we should go in the mesh deck and then check with the unmatched surface.

So there is no unmatched surface, which means we have done matching very well correctly over there. So as we have meshed everything, now we will go with the volumetric mesh. So I will suggest you a few steps to keep in mind while doing volumetric mesh there. So there is an option called define, there is also arrow mark present there, that means something is there in the defined option. So I will long press it, you will find auto detect option. So click on auto detect option, it will ask you to work on either whole database or visible.

So I will suggest you to select the whole database over here. So if you have observed over here, they are also asking the model must be already surface meshed, which we have already taken care of. So now we are keeping this whole database and then we are clicking on OK. So let's give some time to answer and it will show you the volume list for you. So by default, answer had auto detected this eight different different volumes. OK, so volumes are nothing but the closed geometry, which we have closed in the topo mode itself.

Now we want few volume, which we can later on mesh it and few volumes, we will try to delete them. So it's very important task to figure out what volumes are required and what volumes are not required. So as we are meshing this particular component for our CFP applications, we will be meshing only the volumes which are not occupied or which are not taken by our parent geometry thickness. By saying that, what do I mean? So I mean that each and every geometry will have its own thickness.

So that thickness, we should not do volumetric mesh, but we should do volumetric mesh for the space or for the voids, which is there inside of a particular volume where the fluid may flow. Right. So basically, we will be taking the volumes where the fluid will flow and then we'll try to deploy the 3D mesh, which is nothing but tetra mesh to that particular volume. And then we'll delete the rest of the other volumes. So in order to check what are the required volumes present in our this particular list and what are the volumes which we can directly go and delete.

So in order to check that, we should always check the preview over here. So in order to check the preview, we should click once over the particular volume in the list. Right. So we should click on the particular volume just to see the preview. So if you click one by one, you will be able to see the preview of that particular detected volumes like this way. So I told you like we should create a common volume for this particular, all this blade one, blade two and then impeller along with the shaft.

We should consider that as a one volume. So why I told you that? Because we can directly delete that particular volume, which is occupied by the thickness of that particular blades, rotor and then the impeller. So that was the reason why we created a common volume, which is also detected over here and which we will be deleting at the later stage. Same like this, if you can see this PID number 32. So that is the inside volume of our particular casing. So this volume is responsible for accumulating the fluid to flow.

And this PID 33 is nothing but our parent geometric thickness. So whatever material we are using for creating this particular casing, right? So that material will have its thickness. So this is the volume which is detected by that particular thickness of a component, which we will be deleting in the later stage. These are 34 and 35. So 35 is again the thickness of a particular model and 34 is the void or the volume in which the fluid will flow. So 34 we will keep and this 35 we will delete.

So 36 is again this green color component thickness, which we will be deleting. 37 is also thickness of this particular blade one, blade two, rotor shaft and the impeller which we will be deleting. 38 and 38 will be the void or volume where fluid may flow. So we will keep this 38 and also 39. So 39 also we will keep. So in total we will keep the four volumes over here, one volume where the fluid will flow inside this particular casing. This is volume number one, this one.

Then another volume will be this double charger volume. So turbo casing volume where the fluid may flow inside the turbo charger, where the fluid may flow inside the turbo casing. Then we can also keep this particular smaller void which is captured between two particular components. And also this particular volume or void where the fluid may flow inside this, right. We will keep only this four and we will delete the another one. So before doing that, I would also like to show you the volumes by isolating.

So you can always do right click and then show only and you can basically see that volume present over here. So you can see and you can imagine that this is the volume where the fluid will flow. The fluid will have this much volumes to flow inside this particular volume. And this is the parent geometry, which was having this much thickness. So as our parent geometry was closed, it has also considered a common volume inside this particular parent geometry. And it detected as a volume there.

Similarly, here also we have taken this particular volume inside this particular turbocharger casing. Where the fluid may flow. So this is what we required. And this is the thickness component or thickness volume of our particular turbo casing, which we don't want to have. And then we will delete it. So this is the component thickness, which we don't want because the fluid will never pass through the thickness of the component. Instead, it will pass inside the component where the void will be there. So this is a common volume, which we created by deleting the interfered surfaces.

We also checked that if we hide this surface and if we hide the bottom surface, we can able to pass through it. Which means the volume is a common volume, which is detected here. And then we will delete this volume as well. This is the volume between your particular turbo casing and the outer feature, which we will keep. And also we will keep this particular smaller volume. So now as we have checked all of this, we will click everything. We will click on show only to see everything together.

And now it's our task to delete each and every unnecessary volumes one by one. So this is required. This should be deleted. So we will delete this. So we will keep on check and then we will delete the unnecessary one. Make sure you are deleting the right ones. If you don't want, delete this. Also, if you have observed, we are deleting only the thickness components of our parent geometries. So this is how we left with only these four volumes. One, two, three and the fourth one small volume.

Again, this is just a list of a volume which ANSA has detected automatically. Now it's our task to deploy a volumetric mesh here. So you can always read the status over here. So the status says that the volume is unmatched. Basically, you should match that. We will check with the smaller component, which is this component. So in order to match any kind of defined volume or detected volume, we should do right click. Go with the remesh option. In the remesh, they will ask you to select a type of your particular 3D element.

So the 3D element type can be Tetra CFD because we want elements for CFD applications. So we will choose Tetra CFD in which Tetra shows the element type and CFD shows the application of our that particular elements. So Tetra is a 3D element which we can also check over here in Tetra CFD. So either we can go here or we can do right click, remesh, choose this Tetra CFD and click on OK. Once we do that, it will start matching that and you can see the status is now changed from unmatched to missed.

Also, the type is given as Tetra CFD. You can always check the type and the status once you finish with that particular matching for that particular component. So I will follow the same process for each and every detected volume. So I have started with the small components and then slowly I will go to the larger component. Make sure you are giving sufficient time for answer to finish that. Because the elements for the volumetric mesh will be way much than the elements for the surface mesh. Because here in the volumetric mesh, you will be matching your volumes.

So you can consider significant volume for your particular volumetric mesh. Instead, area for your surface mesh. So make sure you are giving sufficient time. It may take up to 15 to 20 minutes. So kindly be patient and then wait for answer to give you the volumetric mesh for you. Also, I will suggest to save your model very frequently. Let's say after each and every 15 minutes so that you do not lose your work throughout the course. So in order to save that, you can basically go to file and then click on save or save as and then give your particular directory or file location and then save there.

So answer will basically try saving your model in the format of dot answer. So as we have matched these three components, we will go with the last component and then we will match that as well. Also, you can check over here earlier, it was only shell details given in the GUI. But here now, as we have started meshing this and as we are there in the volumetric mesh stack, it's also showing us volume data also over here. So shell is nothing but mesh and volume is nothing but volumetric mesh.

So for volume data, we have received tetras over there. So there is a count of tetra elements and there is also count of unmatched volumes, which is nothing but one, which we are currently meshing. So same way, how we are ensuring that in the mesh stack, we should not have any unmatched surface. We should also check in the volumetric mesh that we should not have any unmatched volumes. So if you find any unmatched volume number, you should think of reducing it to zero by meshing each and every autodetected volumes.

So at the end of this operation, you will receive how many shell elements you have, which is nothing but tri element and how many tetra elements you will have. So this will give you an overview of how many elements do your model has. Understand that your volumetric, once you finish with your volumetric mesh, you will have a lot of tetra elements. Due to very high number of tetra elements, probably your software will start working very slowly. So you can always save that in order to avoid your sudden crash of your particular software.

Here guys, so here we have taken the volumetric mesh for this particular component. So it took nearly around 30 minutes. So at the end of 30 minutes, we finally got volumetric mesh component. And now we can check each and every one. So each status is meshed and type is tetra COD. So we can confirm by seeing this and by selecting this that everything is meshed. And now we will check the elements. So I will close this. And I will also suggest you, if you want to see the list again, you can basically go to the volumes and then click on the list.

And you may find this list of this particularly defined and meshed list of the volumes. So here you can see the volumes, which was very low earlier. So that was like increased a bit. So here you have so many tetra elements over here. So there is a large possibilities there. Your software may get very slow now onwards. So you can always save your particular model after finishing your volumetric mesh so that you should not lose your work and you should not lose your time as well.

So now, as we finish this particular volumetric mesh, now we will analyze this. How does it look like? So I will try to show you the particular volume. Before that, if you go to toko mode now, you can see some glitching is present there, right? So the reason why the glitching is present is because the volumes which you have created, that volume is basically a part of this particular volume over here, which is also turned on. If you turn off, you can basically ignore that glitching.

So this particular volume will show you the volumes present over there. So if you turn off your geometry and FE, you can basically check your volumes over there. So different volumes will denote with different colors over here. If you turn off your volume, basically nothing will be visible. If you turn on your geometry, only geometry will be visible. So this is how you can check your volume alone. And then you can take the required screenshots also. So if we zoom in, we can able to see the elements over there.

And if we use not option with entity mode, and then if we select something just to hide that particular region or selection, we can see that after hiding that many elements, we can see the cross-section of that particular hidden elements. So we'll see that once this process will become finished. So every time you use this hide option or not option just to hide any elements over there, understand that it will take some time because it will hide so many elements for you in terms of thousand or in terms of lacks.

So kindly be patient. And then you can check the cross-section like this way. So these are basically tetra elements. You can see over here. So just like this, you can try hiding so many different locations and then try checking the cross-section over there. This is how your volumetric mesh will dance. So understand that the volumes which are present inside your particular model is now filled with so many tetra elements. These tetra elements will later on be used for CFD applications. So till now, we have seen only the surface mesh.

We have not covered any part of volumetric mesh. So in this particular week, we have seen this volumetric mesh which is 3D in nature. And then it will try to capture your volume. And this is the reason why there are so many elements are created if you are creating your volumetric mesh. So the number of elements will be so high than your surface mesh elements. Also, if you want to take your cross-section exactly from the middle, you can also check the same by using this not option.

You can select your entities exactly from the center like this way. And then you can hide the rest of the right side half part. And then you can see how is your cross-section coming up. So here we go. So we tried hiding the half part and now we will see how is your half part. So you can see there is some depression present over there in the location where we had this particular. So once we did this cross-section by hiding the right-hand side of the surface, we checked that this is how our cross-section is looking like.

The location where we had blades, now that location is also visible over here in this particular cross-section. One thing you can check over here is, wherever you had this particular blades at that location, the elements are coming very smaller in size. And then if we go away from that particular blade location or shaft location, the element size is keyboarding. Right. So that is a nice takeaway over here. So the reason why the shaft region or the blade region is making these elements to come very smaller is because that was having element length as 1 mm and this element length is about 5 mm.

So volumes tried coming up with very smaller in a place where the blades was connected and the shaft was connected. And if we go far away from that particular location, it tried increasing its size and you can very well check that over here. So this is how you can check your cross section if we cut exactly from the half. Not only on this top casing, but also in the bottom casing, you can observe the same thing over here. So you may find the location of the blade and the location of your particular impeller over here.

And you can conclude the same. So this is how your volumetric mesh can be done for this particular turbocharger. So just like this, you can take any CFD model and then you can try realizing the volume and then doing the same particular volumetric mesh will be a great practice. So I suggest you guys to follow the same procedure and then do the same for this particular turbocharger and do contact your support engineer if you are facing any difficulties. So this is all for this particular week and this particular class.

In the next class, we'll start with another model, which is nothing but our BMW car. So we'll try creating a BMW surface mesh and then after that, we'll create a wind tunnel and we'll see how the volumetric mesh can be done for that particular model as well. So this is all for today and we'll meet in the next class. Bye. Thank you.

Want the rest of Advanced CFD Meshing using ANSA?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Advanced CFD Meshing using ANSA course

The remaining 2 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Advanced CFD Meshing using ANSA course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.