← Course overviewFree lesson 1 of 3 · lesson 1 of 5Next lesson →

Unlock all 5 lessons of Advanced CFD Meshing using ANSAFull course ₹40,000 · paid

Price & syllabus
Free lesson · 54 min · no payment

ANSA Interface, Topo Tools, Hot Points and Mesh Length

A free lesson from Skill-Lync's Advanced CFD Meshing using ANSA course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “1.0 - Introduction to ANSA GUI and Tools Part 1”

What will you learn in this free Advanced CFD Meshing using ANSA lesson?

The instructor tours the ANSA GUI and the topo, mesh and volumetric mesh decks, then shows the visibility tools (OR, AND, NOT, neighbor), hot points and the measure tool on a cylinder. A second part cuts faces, applies 3 mm, 1 mm and 5 mm mesh lengths with spot mesh, and compares how well each captures a circle.

  • Topo, mesh and volumetric mesh deck order
  • Isolating and hiding surfaces with boolean tools
  • Creating, projecting and measuring hot points
  • How mesh length sets node count and accuracy

What comes after lesson 1?

The next free lesson is lesson 2, “Topo Cleanup, PIDs and Mesh Length on a Pressure Valve” (90 min). Later in Skill-Lync's Advanced CFD Meshing using ANSA course (paid): lesson 4, CFD meshing to BMW M6 Model inside Wind tunnel; lesson 5, Surface wrap to an Automotive assembly. The full course has 5 lessons (12 h 29 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Part 1

Hello, guys. Welcome to Advanced AFT Matching Using Ansah course. So, I would like to tell something about Ansah software. So, Ansah software is basically used for doing pre-processing tasks. So, pre-processing tasks includes topo cleanup. Topo cleanup is nothing but geometric cleanup. So, if you have any model in your Ansah software, in that model, you can basically do some checks just to ensure before matching, you have very nice and corrected model with you. So, that is called geometric cleanup. So, in Ansah, you can basically do few steps like geometric cleanups, then meshing, solving your off elements. You can also give quality criteria to your mesh lens.

Also, you can do 2D mesh, 3D mesh, both. And you can also prepare a solver deck by using Ansah. Also, you can do some morphing, hexamash, etc. So, Ansah is very widely used in CAE applications. So, we will explore this Ansah tool in this particular coursework for the CFD applications. So, starting with Ansah, so I would like to tell something more about this GUI. So, if you open Ansah, it will look like this. So, these are the tools which we can see in the Ansah screen, which we can widely use.

So, basically, start from the tools. So, here we can say there are a lot of tools at the top and at the bottom. But if you want to see the name of the tools or you can say the labels of the tool, you can basically see that as well. So, you can do right click here and then you can click on the show labels. So, you can see, you can be able to see all the labels of each and every tools present in our Ansah GUI.

Okay. So, yeah, I will start explaining each and every tool throughout this course at different, different point of time whenever it requires. So, here at the top, we can see we have some managers. So, if you hover a mouse over there in over a particular tool, then basically you can able to see the name of that particular tool. So, you can read the description as well and also you can find the shortcut key also. So, we will explore each and every tools from this Ansah GUI and then we will start with the course.

So, this you can see properties. So, this is basically property manager in which you can assign different, different properties to different, different surfaces. And also, you can assign the thickness as well. Okay. So, this is called property manager, which we can see in the later stages. This is called material manager. So, here we can assign the materials to the different, different models or different, different surfaces as per our requirements. Similarly, we have a few things like batch manager, then feature manager, etc. So, all these things will look.

Also, if you are trying to match something, basically we will be dealing with match parameters and then quality criterias. So, if you open match parameters, basically you can give different applications of your particular mesh, different types of elements used while matching. Either it can be first order or second order. Also, you can give the target length, minimum target length, maximum target length as per your quality criteria given to you. So, all these things we will see one by one. So, here we will have few decks present at the top over here.

So, if you see here, we have topo deck, match deck, volumetric match deck, and then solver deck. So, in this course, basically we will be working with topo deck, match deck, and volumetric match deck. So, topo is basically deals with the geometry of a model, or we can say 2D surface model or CAD file of a model. So, we can also do some corrections in our surface, we can also create surface, delete surface, we can create points or curves as per our requirement. Also, we can try to paste two surfaces together, two cons together, and then we can finish our topo cleanup.

So, what are the cons, and what are these curves and hot points and all? So, we will see it one by one. So, topo is generally used for dealing with geometry of a CAD file. Match deck is basically used for meshing a CAD file, which you have already worked in the topo mode. So, after topo cleanup, you can basically start with match. Before match, you should check that you don't have any geometrical error present in your model. For that, you should perform few checks over there.

Only after confirming that you don't have any errors, you can basically start with mesh mode. So, these are the mesh deck tools, which we can use while meshing or while improvising the mesh. After that, we have volumetric mesh deck. Here, we can do volumetric mesh directly. So, these are the tools, which we can widely use for that. So, the sequence like topo, mesh, and volumetric mesh is supposed to be followed one by one. So, only when you have finished your topological cleanup, you can go with the mesh.

Only if you have finished with your mesh, you can go with the volumetric mesh. So, you may wonder what is mesh and what is volumetric mesh. Basically, mesh, as you can see in the icon, so it is having 2D elements there. So, you can see. So, first of all, in topo, you can see a surface with yellow color. That means topo is dealing with surface only, that to your care geometry. In mesh icon, you can see that surface is now having a lot of elements over there.

We can see it's discretization process. So, after discretization process, you can have a lot of elements over a surface. So, if you have elements over a surface, that elements are called as 2D elements. 2D elements are basically tri-elements and quad-elements or combined tri- and quad-both. Right. So, those are called 2D elements. Similarly, if you can observe over here, this icon shows like that surface is also having a thickness. So, now, this 2D mesh convert into 3D mesh over here in the volumetric mesh. So, you can see the surface is no longer a surface, but it's a volume kind of thing.

So, whatever elements you had in mesh, that elements now are having certain thickness. So, volumetric mesh, you can basically deploy over a CAD in two different methods. We'll see both the methods one by one in the later stages. So, 3D elements are basically tetra elements and hexa elements. For CFD applications, mostly we'll be using tetra elements. So, starting with ANSA, we can basically import a model first as a first step. So, we'll see how to import a model now. So, at the tool bar, we can see file option.

So, if we click on file option, we can click on open. Once we click on open, if you have opened any model earlier, then it will ask for confirmation about the previous model. So, either we can save or we can discard. After we discard, we can basically open a new model. So, in order to open a new model, you can go to certain path where you have your .anser file. So, basically, .anser is extension of model which is exported from anser. So, if you export any model from anser, basically, you will have .anser extension there.

So, you can click on open. So, it will take some time and it will open a model for you. So, this is how the model will look like. So, this is a kind of cylinder. So, I'll also tell you about the mouse controls over here. So, basically, if you want to rotate your model, you can basically press control and you can press your left click and then you can try moving your model. You can basically try to rotate a model. So, this is basically used for rotating a model.

So, again, I'm repeating. So, you can do control and left click. And then, you can rotate your model. So, if you want to pan your model, you can use control and your middle mouse button which is nothing but a scroll button. You can press both of them together and then you can try moving it. So, it will pan for you. So, again, if you want to rotate about any axis, you can basically press control and right click and then you can rotate about certain axis. So, this is about mouse controls.

If you are not good with mouse controls and if you want to give your own mouse controls, that can also be done. So, for that, you can basically go to the tools. Here, in settings, we have GUI settings in which we can find mouse and keyboard. So, here, by choosing this different control plus left, middle and right click, we can change our mouse controls. Right. So, you can also explore these buttons and you can set your own button operations as per your requirement and as per your practice.

In order to zoom in and zoom out, you can again press control and then. You can scroll up for your zoom out and scroll down for your zoom in. This is regarding your mouse controls. So make sure whenever you are working with Hansa, you basically press control and then use your mouse controls in order to move your component or in order to zoom in, zoom out your component. So it's always desirable to use your left hand for control, for pressing control and pressing escape simultaneously whenever it's needed.

And your right hand to use your mouse buttons. So this is how you can basically have controls over Hansa. So this is regarding your mouse controls. Now we'll start discuss about the model. So as this is very first lecture, I have taken very simple model, which is nothing but cylinder. So you can see the cylinder is having hexagonal shape at its face on both the sides. But its surface seems like circular. So there are a few topological cleanup we can do in order to obtain a perfect shape over here.

Before that, I wanted to convey a few things about the model. So if you find any closed model, that model should have double cons. Double cons are basically the cons which are shared by two surfaces. So here you can say the yellow color line. So yellow color line represents double cons. Double cons are basically the cons which are shared by two surfaces. Here in this case, this will be surface number one. This will be surface number two. So if surface one and surface two are joined together, then it will form a double con at the middle part.

So the edge which is shared by two surfaces are basically double con. Similarly, here also you can see there is one surface here. One surface here. That's why it is forming a double con here also. So now we will use some boolean operations. We will explore the boolean operations which will be useful in order to hide or retrieve back any kind of surfaces. So there are a few options at the bottom which are called boolean operations. So you can see OR option. So OR option is basically used to isolate any kind of surface.

If I want to isolate only this front surface and if I don't want to see any other surface than the front surface, basically I can use OR option. Then I can click on the crosshatch of the surface. So this dast line are nothing but crosshatch which is used to pick any surface. If I want to pick this surface, basically I need to click on any crosshatch, either this horizontal or this vertical. If I click somewhere outside my crosshatch, it will not be able to select. So this is the function of the crosshatch.

The same crosshatch you can also enable and disable by turning on and turning off this icon over here. So this icon also shows you it's a crosshatch and it will show or hide the crosshatches. If you click on that. So as it is disabled, you can see you are not able to see the crosshatch. So now if you want to pick any surface, it will be very difficult for you to pick any surface because you don't have crosshatch enable in your model. So it is always preferred to use crosshatch enable every time when you are working with ANSA.

If you are opening a model or if you are opening an ANSA software and then if you are finding that the crosshatch is not turned on, the first task which you can do in ANSA is you can turn on the crosshatch. So coming back to this OR operation, so we can click on any surface. So just a minute. So coming back to this OR operation, we can click on any surface and then you can see that surface is isolated and then rest of the other surface is getting invisible.

So don't think the rest of the surface is getting deleted. It's just getting invisible. So this is how you can have one surface alone in your screen. If you want to isolate any particular surface in your model, you can basically use OR option. If you want to have the neighbor surface also visible, you can use AND option now. And you can click on any double cons over here in order to see the surface coming up again. So we can basically use AND option to retrieve the neighbor elements back in our screen.

So we can say OR and AND options basically used for isolating and then retrieving back the surfaces. So those are kind of opposite tools. So OR is used to isolate and then AND is used to retrieve the surfaces back in your screen. So similar kind of AND, we can also use the neighbor option. So we'll see how it will work. So again, I'll separate this particular surface and then we'll show you what the neighbor will do. So neighbor option, if you can see, there is a drop down button over there, which is present there.

So you can long press that and you can see there is a first level and all option. So if you click on first level, it will kind of retrieve back the surface which are attached with this many double cons present in your screen. So you can basically use neighbor first level. You can see that this surface is not coming here because that surface has no relation or no context between that front surface. Only this surface had a relation or had a context with this front surface.

That's why it's came back. But here this surface was total entirely separated from that surface. So that didn't come. So if you want to take that surface also visible, you can basically use neighbor OR. So we'll check that again. So again, we are isolating this. Now this time we are using neighbor OR. You can see all the surfaces are coming up. So this is one way of retrieving all the surface back. If you don't want to go with that option, you can basically use this all option also.

Let's see how it is working. So we can click on OR, isolate this one surface. Then we'll click on all option. So you can see everything is coming up. So what is the takeaway here? So the takeaway is neighbor OR and the normal OR option. Both are working same way. Right. So you can use either OR or you can use neighbor OR. Right. Same way, neighbor first level and AND option. Both are working same way. So you can use either neighbor first level or you can use AND option.

In AND option, you will have one provision only on the CON which you are clicking after enabling this AND. Only that surface will come up. But if you are doing neighbor first level, all the CONs which are visible in our screen of the isolated surface. So all the surface which are joined with that particular CONs, all the surface will come again in the screen. Okay. See if I want to demonstrate that again, I'll demonstrate that as well. So we can use OR to isolate this. Now, I want only the surface which is connected with this particular CONs.

So I'll click over here and you can see only that surface is coming up. So other surface is not coming up. So I will do control Z. Now, if I use neighbor first level, basically all the surface which are joined with this particular all the CONs are coming up. So this is the difference between AND and the neighbor first level. So, yeah, you can always use this undo and redo options just to take one action back or one action forward. Also, you can use control Z also if you want to do some undo actions.

So this is regarding your this particular OR, AND, AND neighbor and ALL option. Now coming to your NOT and I NOT option. So NOT option is basically used to hide any one of the surface. So in earlier cases, I showed you how to isolate this surface alone. Now I'll show you how to hide only this surface. So if I want to hide only this surface, then basically I can click on NOT and then I'll click over here. So you can see the surface is hiding over there.

Same way, if I want to hide any surface from here, you can also click on that and then you can find both the surfaces are now hidden. If you want to retrieve it back, I can click on AND. Click on that same way here as well. OK, so this is the function of NOT option. So what is I NOT? So basically I NOT is also used for isolating a surface. But here you need to click twice a middle click in order to execute a function. If you want to isolate this top surface, you can basically click once.

If you click once, if you click once, it will be hidden. If you click again, then it will be isolating. So the only difference over here is in R option, you can only click on that and it will be isolated for you. But in the I NOT option, you need to click once here and then do middle click here in order to isolate this. So it's totally depends upon you how well you are using this. So it's totally depends upon you how well you are using this.

So you are using this. So you can see if you click on that. So let's give you a bit of a little bit of a depth. So let's go to the left side of the surface. Boolean operations in order to see or hide any surfaces. Now we'll see what is invert. Let's say if I want to see only surface. Right. So I will be using R option over here. But what if I want to see the surface other than this surface? Then I will use invert option. Right. So basically invert will invert your view. So whatever view you had, the invert view can be visible if you click on invert. Okay. So it is much useful if you want to deal with one part and then next another part. So these are the tools which you can basically use. After that, I'll show you the different tools of Topo. So starting with hot points. So I'll tell you what the hot point is. So basically you can see here.

There is a pink color points over there. Similarly, pink color points over here. Right. So these points are called as hot points. Hot points are nothing but the points which are present at the starting of the line and which are present at the ending of the line. And this line, we have two hot points, one over here and one over here. But it's not necessary that in a line that should be only two hot points, it can be many hot points. You can also have an option to insert the hot points and then delete the hot points. So if you want to insert any hot points, you can basically click on insert and then you can insert a hot point over here. Same way if you want to delete the hot point, you can click on delete and then click on the hot points. It will delete for you. Same way if you have a hot point over here and if you want to delete that hot point. Apart from delete also, you can delete the hot point by using insert also. So for inserting hot point, you can basically do left click there. In order to delete the inserted hot point, you can do right click over there. So if you do left click, it will insert, if you do right click, it will delete. So insert and delete, you can basically use by doing left click and right click while activating this insert option. Let's say if I have a hot point over here, so I'll create a hot point over here. So I have created a hot point over here. So if I have hot point here and if I want to create a hot point somewhere over here in this line, that too perpendicular to this hot point, then we can use the project option in order to project our hot point. So if we click on the project, we can read the instruction at the bottom. So they are asking to select the node which we want to project. So we can click on this. You can see the white color selection. White color is basically shows us the selection. So we can select the con now. Sorry, we selected the point. Now we can select the cons. So it's asking to select the con where we want to project this particular hot point.

So as we discussed, we want to project this hot point over here somewhere. So I'll click on this con. You can see one hot point is created over there. So basically project option is used to project any hot point. So this is how you can basically project a hot point. Now if I want to create a hot point exactly at the middle of a line, then I can do that as well. So consider this is a point from the starting of the line and this is a point at the ending of the line. So if this is my line, then if I want to create a hot point exactly at the center of my line, then I can use parametric option. So I can click on here somewhere. So just remember, we should click on the con on the direction where we want our hot points to present. So I clicked over here, you can see there is an arrow mark present over there. Okay, so arrow mark is showing me in this direction. What if if I click on here, if I click here, you can see the arrow mark is showing in this direction. Similarly, if I click over here, the arrow mark is showing in this direction. The takeaway is in whichever direction we want arrow mark, we can click on that particular direction from that particular hot point. So now in this case, as I want a hot point exactly at the middle of this particular line, I click somewhere over here, then there is a box coming up. In the box, I can write 0.5 over here. So why I'm writing 0.5 here, because this line is now considered as 1 mm length.

So they're asking me at what mm length you want your hot point to create. So as I want to create hot point at exactly at the middle portion, I will consider this line as 1 mm. So I will write 0.5 mm over here. And then I will click on OK, create a hot point over here. Same way, now this is my line. Earlier, this was my line. But now as I have created one hot point over here, now the line is reduced to two lines. And the length of the line is now this much. And also this much. So same way, if I want to create a hot point somewhere over here, in the middle, I can again do the same procedure, I can click somewhere here, I can see the arrow mark, I can write 0.5 and then I can click on OK. You can see there is also point coming up over here. Now, if I don't want my hot point to be present at point exactly at the middle, but somewhere over here, then I can do the same. I can click here. And then I can write 0.2. And click on OK. So you can see, this line will be 1. And then this length will be 0.2.

So they are asking us, at what distance you want your hot points to create by considering this line as 1 m. So this is regarding your parametric option. So if you have a specific distance with you, then you can write the distance also. So how? Basically, here if you can see, they are suggesting that please specify the upper, like from 0 to 1, or this symbol and then write a distance. If you have a distance with you, basically you can use that symbol over here. And then you can write a distance there. And then click on OK. So it will measure a distance at 2 mm and then it will create a hot point there. Okay. So the takeaway is, if you have distance with you, you can basically use this sign and then you can write a distance or else if you don't have any distance or measurement with you and if you just wanted to create a middle point, then you can basically use 0.5 without any sign and then you can click on OK. So that was all regarding parametric options. So that is the option called undo over here. So if you have done five tasks, then you need to basically do undo for the five times.

If you don't want to do undo for the five times, you can basically do undo for the multiple steps. How? So basically you can observe an arrow mark present over there, which is nothing but a drop down menu. So if you click on that, it will show you the actions of your particular work. So this many actions you have done after opening a model. So it will show you this many actions. If you want to undo few actions, you can select few actions and then you can click on that. So it will undo for you. Now the same way, redo also you can do for the multiple steps. So there will be few steps present over here as well.

And then you can do redo also. So this is how you can basically use these options very nicely. That is regarding your parametric cut. Now, what is this multi project? So we have seen the project, right? So I think you are aware of what does project will do. Let's say if I have multiple hot points over here in this line and all the hot points I want to project on this particular one, then I can use multiple project. It will ask me to select either nodes or nodes from cons.

So basically, if I want to select the nodes, I can select all the nodes like this way. And then I'll do middle click. And then I will select the con. So I want all these hot points to be projected together over here. So I'll click on this con and then do middle click. You can see all these cons are coming up there. So this is one way of method. I'll do control z. So the another method is if I click on multi project, there is an option called nodes from cons. If I enable that, they are asking me now to select the con. So I will select the con where I have multiple hot points present. So I will select this con, this con, this con.

So all these cons I will select and then we'll do middle click and we'll click over here. So And it will do the same for you. Right. So this is regarding your multiproject. So control Z and control Z. So these are a few things which you can basically do. Now, what if, if I want to measure distance between disk on and disk on? If I want to measure a distance, there is an option called measure over here at the top. If you don't find this measure option at the top, you can basically click on the utilities. And then from here, you can find out this measure tool. So you can click on the measure tool. So they will ask you to measure a distance between this various entities, either between two nodes, between two edges, between two shells, solids, between two cons or the other entities.

Now we are interested to measure the distance between this node and, sorry, this hot point and this hot point. For this point of time, these points are considered as node. So you can use the same way. You can click on the node over here and click on the node over here. So it will show you to measure the distance. So it will show you the distance. The distance is approximately 190 mm. So this is regarding your length. Okay. So also in the results, you can find out what kind of results can you get, right? So you can basically find the distance. You can find the COG point coordinates. So here you can find these coordinates.

So if you have this line with you, then where will be your COG, what coordinates will be your COG. So that also you can find out. If you want to figure out the angle with plane X, Y, you can also do the same. So the angle is minus 82. Similarly, angle with Y, Z plane. You can compare your global coordinates. You can see this will be your Y, Z plane. So from Y, Z plane. How much is the deviation? Right. So that you can find out over here. So the takeaway is, with the help of nodes, you can always find out the distance in majority of the cases.

Okay. So it can be this two node. It can be this two node or it can be this two node as well. Okay. So what if, if I want to go with the other measurements now? So for that, I will do middle click and then I will again choose a set of hot points over here. Okay. So it will show you the two measurements there. So again, if I want to go with the third one, I'll do middle click and then I will click into sets of nodes and then we'll see that out.

So this is how the measure tool will work with the help of nodes. So yeah, that's all for this class. In the next class, we'll see the further things like what are the other things we can check by using major tools. So this is all for today. We'll see you in the next sessions. Thank you.

Part 2

Hello guys, welcome back. So in the previous class we have seen about the different different options and the hot points and also the major tool. Right, so now today we will see few tools in the faces. Right, so basically faces is nothing but surfaces. So if you want to make that cut or a deleter surface or retrieve back the deleted surface or create a new surface, all those things you can very very do in the faces tool. So in the faces section we have lot of tools which we can explore in this course. For this particular model we will explore the cut option now. So we have discussed that if you want to create any middle point in between then we can very well do that by using this parametrical option. So we can choose parametrical option, we can choose the direction and then we can write 0.5 and click on OK.

So it will create a point over here. So same way now I will cut everywhere in order to create few cuts over here. So just see where I am creating the points over here. So this is how I have created points over here in this particular face. Now I will try to project all these points on the other face over here. Right, so there is an option for that. Basically we have used project option in order to project one point to the other face. But what if we have this kind of multiple points present over here.

So in that case you can basically use multi project option. So you can click on that. Then you can select all the nodes one by one. Nodes in the sense, points in this case. So you can select those. Once you select all the nodes, you can do middle click and then you can select the cons. So you can select all the nodes. So you can select all the nodes. So you want to project all those selected points or nodes on this particular cons. So it will project on the other face. Right, so like this we can project all this. Once we project these points, we can basically create a lines now. Lines in the sense, we can make a cut on the faces. For that we can use cut option in the faces section.

So if we click on cut. Basically we should select first point and the last point. As we all are aware of, any line can comprise of two points. First will be initial point and second will be last point. Same way I will select each and every cuts. And then we will do middle click or click on OK. So creating cut is so easy. Basically you need to select the first and second point in order to create a cut in between. You can always see a preview like this. So if you can see the green color preview, that means this is how your line can come. But if you think you can make a cut from this point to somewhere on this point.

Basically that can also be done. OK, so you can see the preview. So the preview will enable the cut images. So how the cut will look like. That you can basically very well check by using this preview. OK, so you can always check length also while creating a cut. So what will be the length of your cut that can also be checked by using this option. If you can see there is a measurement given over there that is 2.67. So same you can also check everywhere else. At the end you can create a cut like this. Once you are finished with cut.

If you don't want to do any cuts for now, you can basically press escape from your keyboard in order to deselect your particular options. As you can see in the cut. When the cut option is enabled, you can always see the cut option enabled over here. You can either click on this cross over here or else you can simply press escape from your keyboard in order to disable that cut from here. So this is one of the most important things. So I'll suggest you guys to use your left hand for pressing control for moving this.

And you can basically operate this escape very frequently with your left hand. So use your left hand for your control and escape for your keyboard. And then right hand for your mouse controls. This is very handy. If you think you can only create the cut if you have the points there, then it's not like that. You can basically create a cut even if you don't have any points present on your particular face. Let's say how it is working. Basically you can click on cut. You can click somewhere over here wherever you want to start a cut.

So basically click over here and then I will click over here as well. So you can see there was no points present over there. Then also it's creating cut for us. Same way I can create cut as many as I can. This is regarding your cut option. Now you may wonder if you have created a cut over here, let's say, and that cut you don't want now because you have done that cut by mistake. So if you realize that the cut which you have created that is of no use and you have created that by mistake, basically you can remove that cut as well.

In order to remove the cut, you can basically click on cut and then you can do right click over here on any kind of cut. If you do right click there, you can basically see that the cut will go from there. So I'll do undo. I'll do the same thing again. Click on cut and then click on any one of the cut with the right click. And it will go away from your model. So this is how you can create a cut and then delete a cut as per your requirements.

Now let's go to the part for matching. So basically this is what we can do for our geometry. Once we finish with this, we can basically start with our matching. So in order to start matching, we need to go to the match tag. We'll click on that. Any mesh should have its mesh length. So if you understand what is mesh basically, mesh is nothing but a segregation of a very large surface into very smaller surfaces. It is nothing but discretization process. So the same thing you can give your mesh length over here by using this parameters length option.

So just make sure whenever you are starting with your mesh, you just give your mesh length first and then only you just go with the mesh. In order to give mesh length, you can basically click on length. It will ask you to select parameters and macros. Make sure you should give parameters and macros both as your mesh length. So you may wonder what is perimeter and what is macros. Perimeter is nothing but lines which you can see over here with green colors. Those are called parameters. Macros means the surface which is bounded by so many parameters called as macros.

We want mesh length as the given mesh length and also we want macros also as given mesh length. What do I mean by mesh length now? So you may get confused what is this pink color things. Just to clear that, if you go to topo mode, you can see the pink color points. Those are basically hot points. So just remember in the topo, if you can see the pink color points, then that points will be hot points. In the mesh mode, if you can see the pink color points, that is basically nodes.

So I will suggest you to not to confuse with nodes and the hot points. So nodes are entirely different with the hot points. The number of nodes can be varied as per your given mesh length. If your mesh length is small, the number of nodes will be high. If your mesh length is high, then the number of nodes will be low. So now you may understand what is the mesh length now. Mesh length is the distance between two nodes. If the mesh length is 5, that means the distance between one node and another node will be 5.

If you have a line of 10 mm and if you are giving mesh length as 5 mm, basically you can have 3 points over there. Similarly, if you have a line of 10 mm length and if your mesh length is 1 mm, then you will have 11 nodes. So same like that, if your mesh length is low, your number of nodes on a particular line will be high. And if your mesh length is high, your number of nodes will be very low. So, number of nodes will also affect your mesh element size. If your mesh length is so small, basically your elements will be much smaller. So, we will see that tactically how it is applicable.

Just understand, now this model, we will be giving mesh length as 4mm or let's say 3mm and then we will see how the mesh element will look like. So, in order to give the mesh length as 3mm, as I told, we should give 3mm in the parameters and 3mm in the macros as well. So, how to give 3mm mesh length in the parameters? So, as we are there in the parameters, they are asking to select the cons. So, basically we can select each and every cons.

But, if you think there are a lot of cons and to select the cons one by one will be a bad idea, you can basically do a box selection. In order to do box selection, you can press shift, you can press your left click, then you can make a box selection. You can see there is a white color entity which is getting selected. In order to confirm the selection, you can basically do middle click. If you do middle click, it will ask you to select the mesh length.

So, I will write mesh length over here as 3mm and then I will click on OK. So, parameters is given as 3mm mesh length. Same way, I will do for macros as well. Yeah, so here I have finished with my mesh length. Not only this, but also there are two more parameters we need to, which you need to take care of over here. That is, mesh parameters and the quality criteria. The mesh parameters, you should basically give target length as 3mm over here. Also, you can define your mesh element type as tria.

Most of the CFD applications will be using tria elements as our mesh element type. You can click on OK. You may get some error over here, but I will not suggest you to go through the error as of now. We will discuss those errors at the end. So, now just consider that you need to give your mesh length and then you can basically start your mesh after that. As a beginner, I will suggest you to give mesh length in the length, parameters and macros and then in the mesh parameters over here.

Once you do this much, you can basically now start doing mesh. If you want to deploy any mesh over any kind of surface, you can basically use mesh generation section. In mesh generation section, you may have few buttons which will be very useful to deploy a mesh. There are few algorithms in ANSA which will help you to deploy the mesh. So, those algorithms are basically free mesh, batch mesh, CFD mesh, spot mesh. Also, you may find the paste mesh. If you want to see what is there inside this particular section more, you can basically do right click over here and then you can see over here.

If you want this paste mesh to come outside, you can again do right click over here. Same way, if you do right click over here, it will again go back. So, in each and every section where you find this small arrow mark, you can consider there is something lot more inside that. So, you can basically click on that to see that. If you want to just see, you can do left click. If you want to explore and then take the things outside, you can do right click there.

And then you can do right click again over a particular tool. This is so easy. Coming back to the mesh part. If you want to do a mesh, you can basically go to the mesh generation section. There you can find based, free, spot mesh, batch mesh and then CFD mesh algorithms over there. For now, I will use spot mesh now. So, I will click once a spot mesh. They will ask to select a face. Now, it's our turn to select a face. So, I can select a face like this and I will do middle click.

If I do middle click, I can see there is a mesh deployment present over there. Same way, I can select all the surfaces one by one and then I can deploy my mesh over there. You may wonder, what if I want to select all the surfaces together and then deploy a mesh. That can also be done. Basically, you can press shift, make a box selection, select everything, middle click. It will mesh it for you. So, in one shot also, you can mesh all the surfaces. Make sure you are selecting only the surface if you want to be meshed by 3mm mesh length.

Anywhere else, if you want 4mm or 5mm mesh, then you don't have to select that and mesh that now. Instead, you can first change the mesh length to 4 or 5 and then only you can do that. Here in this case, we were expecting only 3mm mesh length throughout our geometry. That is why we gave 3mm mesh length to select all the model and then we deployed spot mesh by selecting everything. Now, this is regarding 3mm mesh. Now, as I told, if you go to measure tool with the help of nodes, if you find the distance between two nodes, you may find the distance will be approximately 3.

So, mesh length is nothing but distance between two nodes. Let's figure out what if, if I do mesh length as 1mm now. I will click on length. Yeah, before that, whatever mesh you have deployed over here, you should erase those mesh. In order to erase the mesh, you can click on erase, you can select everything, then do middle click. It will erase it for you. Once you erase that, you can again go to length. Go to perimeters. Select this and give it as 1mm. Do the same for your macros.

Do the same for your target length in the mesh parameter. Once you give 1mm everywhere, you can basically go to spot mesh. You can long press that. You will have few options. Earlier, you were clicking on the spot mesh only once. So that by default, it was selecting select. So, if you are clicking on each and every tool, it will try to select the first option, which is there inside the drop down. In the spot mesh, the first option is select. So, if you click only once on our spot mesh, it will select the select option.

Then it will ask you to select each and every face one by one. But, if I want to deploy mesh to the visible entity, which is nothing but my whole model now, then I can go to visible and then I can click on that. So, it will deploy mesh for you. You can see, so this mesh is much more finer than the earlier case. Now, in this case, if we go and if we can measure the distance, it will be near to 1. So, this is how we can deploy the mesh as per our quality criteria given.

Same way, let's try increasing the mesh length and we'll see what will happen if we increase the mesh length. So, again we will, it is this, then we will give the mesh length as 5mm. Doing some error. So, the error is, basically it's saying that your mesh length is more than your cut location. Okay, we will see the distance. Distance is correct. Let's give length as 5mm again. For now, you just don't worry about these errors. You may understand what is this error about. So, as this 5mm length is given, I will again go to spot mesh and then do visible.

It will make a mesh for you. So, now, if you compare the case of 5mm mesh length and 1mm mesh length, you can consider that the resolution of your cat or the shape of your cat, which is actually circular, will not be circular if you are meshing with 5mm. If you are meshing with 1mm, it will be proper circular. So, the main takeaway over here is, if your mesh length is very small, basically you can capture your geometry very well. So, if your mesh length is going to increase, your main geometry will not be captured properly.

Right. So, this is how you can match a model. So, you may wonder, if you want to just hide these particular nodes and the hot points, how can I do that? So, that is also an option for that. So, you can basically use the pairing points option. So, if you click on that, it will hide your pairing points. Pairing points are nothing but the hot points and the nodes. So, by enabling and disabling this, you can basically hide and unhide your particular hot points and your nodes.

Just like this. Same way, if you think, what is this green color line? So, this green color line is nothing but your double cons, which is shown as green color lines in the mesh mode. So, if you want to hide that as well, you can hide your double cons from here. If you hide the double cons, not only the double cons will hide away, but also the nodes and the hot points will also be hidden. So, this is how you can finish your work.

Want the rest of Advanced CFD Meshing using ANSA?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Advanced CFD Meshing using ANSA course

The remaining 2 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Advanced CFD Meshing using ANSA course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.