Lesson finished
Lesson finished
Lesson finished
Unlock all 5 lessons of Advanced CFD Meshing using ANSAFull course ₹40,000 · paid
Topo Cleanup, PIDs and Mesh Length on a Pressure Valve
A free lesson from Skill-Lync's Advanced CFD Meshing using ANSA course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “2.0 - 2D (Surface) meshing to Pressure valve Part 1”
What will you learn in this free Advanced CFD Meshing using ANSA lesson?
The instructor runs ANSA geometry checks for single cons, cracks and triple cons on a pressure valve, then closes the open surfaces with the New, fill hole and loop tools. The lesson creates and assigns PIDs, sets target, minimum and maximum length, and compares 5 mm and 1 mm spot mesh on the spring and valve head.
- Running geometry checks for single and triple cons
- Patching open surfaces with new and fill hole
- Creating, colouring and assigning PIDs
- Choosing target length for small components
What comes after lesson 2?
The next free lesson is lesson 3, “Closing and Volume Meshing a Turbocharger Model in ANSA” (121 min). Later in Skill-Lync's Advanced CFD Meshing using ANSA course (paid): lesson 4, CFD meshing to BMW M6 Model inside Wind tunnel; lesson 5, Surface wrap to an Automotive assembly. The full course has 5 lessons (12 h 29 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Part 1
Hello guys. Welcome to Advanced AFT Matching Using Ansah course. Yeah. So here we have another model named wall. So basically this is wall. So we can start with this model. So first of all, before starting this model, we should do a few steps here. So as we discussed in the last class, we have different, different decks named topo, mesh, volume mesh, and then solver decks, right? So here in this video, basically we will be working with topo mode here. So topo mode is basically used for checking the topology of the model. So here we have a lot of tools which are used for solving our topological cleanup. So we'll start with the topological cleanup. So before that, we should always go for decks. So there are decks called geometry decks, which will help us to check our model.
So if you want to go with geometry checks, basically we should find that over here. So here you can see there is a option called checks. In the checks, we have a lot of checks. In that, we can basically go with geometry checks. If you click on that, the geometry checks box will come up. Here, if you can see the templates, we have lot of checks available in the answer software. So these are inbuilt checks, which we can basically use. So here the first is answer checks. Here, if you can see there is a geometry written over there. That means it will take our geometry. Also, there is option visible activated there. That means whatever is visible in your screen, you can take those IDs.
So here at the bottom, if you expand this window, you can see a lot of different different checks, which we can check over here. So the name of the things which answer will check is also given. And the peak mark shows those particular factors are enabled for check. So here we will be checking a few things. So we will be checking single cons, cracks, overlap faces, needle faces, triple cons, clutch cons, unchecked faces, and then unmatched macros. So unmatched macros, we will not be checking now because we have not matched yet. So we can basically check unmatched macros on the later stage.
Right. So we can basically check these things now. So if you click on execute, it will take some time and then it will show some errors. So these are the errors which Ansa is showing you. So these errors needs to be solved. You may wonder what is single cons, what is cracks, and where it is available in our model. So if you have seen in our previous class videos, we have discussed about the cons. So now you are very well aware of what are the single cons and how it look like.
So if we see in our model, so in the model, we can see the single cons is represented by the red color lines, which means those cons or those edges are not shared with two surfaces. Those are shared with only one surface. Ideally, it should not be like this. So if it is filled with any surface, basically, it will form a double con. So we are not expecting single cons over a phase where we actually expect a closed surface. Right. So we are not expecting this surface to be open over here. So we'll try to fix all these single cons which are coming up.
So in CFD applications, basically, we will be closing our geometry so that we can do the volumetric mesh inside this. On the later stage, we can do CFD analysis. So the first task is to check the single cons and to finish to close up a volume so that it will do volumetric mesh afterward. So if you want to see like where are the single cons are available, basically, you can check by selecting those. If you select those, the preview will be shown in the model itself over here.
You can see same way. You can also check the cracks and the other errors like this. OK, so, yeah, you have as many errors over here and it's now your task to solve these errors first. This is basically called as topo cleanup. So whenever you are opening any model in answer, the first task should be checking your geometry and solving the geometry. Only after that, if you confirm that the geometry is well enough for mesh, you can basically start the mesh. So now as we saw, there are a few single cons.
There is another way to check single cons very quickly. So here at the bottom, as we discussed, there are a few visibility tools. Which we can use for checking the single cons. Right. So here we can basically turn off the double cons, triple cons and the cross edges. Now if we do control and shift for wireframe mode, we can check all these single cons together. From here we can see and we can check whether single cons are expected or not. Like told, no geometry should have single cons.
So here we can find out this many single cons. We will try to solve these errors by patching up the surfaces there. So now again, turn on everything. Then think of how we can solve this. So as I told, in this particular operation, we will be particularly use topo deck over here. So in the topo deck, we have various options over here. Okay. So we can deal with many things in this topo mode such as hot points, cons, faces, surface, curves, points and auxiliaries. Right. So basically, what is hot point?
So hot point is nothing but a point. So we can see over here, if I can show you. So any line can have two points. One will be starting point, one will be ending point. So that point can also be considered as hot point. If you want to see the hot point, you can basically zoom in. Then you can check the hot point over here. Basically, hot point is shown as pink color points over there. Okay. So as I told, if you have a line, basically, it should have two hot points.
But yeah, if it is having more than one, more than two hot points, then basically, you should think of deleting those. So those things we will check in the later stages. So this is basically hot points. This hot point section is basically used for checking the hot points, inserting the hot points, deleting the hot points, protecting the hot points. And then by using well spot, we can also check the thickness. That also we can check in the later stages. So as the name suggests, the hot point section is basically used to deal with the hot points only.
It will not deal with your surfaces. If you can see over here, there is an arrow mark present over there just beside the hot points. That means there are a few tools also available in that particular section, but it is not visible in this model buttons. If you want to see that, basically, you can do right click and then you can see those. If you want to add anything over there, then you can again do right click over there. And then that button enable in that particular hot point section.
Same way, each and every section, you will have the arrow mark. If you see the arrow marks, that means you have a lot more tools inside the particular sections. Okay. So now here, the task is to patch the surfaces. So basically, as I told surface, basically, we should check these faces and we should check the surface. So we will be dealing with only these two sections for now for creating new surface and patching this problematic surface. Starting with this front side. So basically, this you can patch by using various options.
So there is an option called new. If you hover a mouse over there, you can see the description written over there. So it says, define a new face. So basically, new option is used to create a new surface, as the name suggests. If you click on new, you may find various options over here. Okay. So you may wonder what are these tools, right? So basically, these are the different algorithms which you can use for creating a new surface. As the name suggests, existing surface, which is used for filling a hole, which is present in the existing surface.
So we will show you that as well. Let's say this is a hole which is present on this particular surface. In that case, we can use this existing surface option. How this option will work? So basically, if you enable that, you can also read the instruction at the bottom. If you read the instruction, it says, select the cons. So we will select the cons. Basically, we should select all the single cons in order to ensure that we want this particular surface. So as we have selected the cons, in order to do the next step, we should do middle click for confirmation.
If you do middle click, you can see there is an option. That is instruction, ask for selecting a face. So they are asking to select a face which is already present over there and on which we want a new surface. Basically, that surface is this one. Thank you. And as you know, if we want to select any surface, basically we can select only with the help of cross edges. We'll select the cross edges and you can see there is a surface created over there. So this is how the existing surface option will be used.
So that is one tool which we can use to create a surface. But as I told, all these four different different algorithms will be used specifically for different different applications. Right. So now we'll see about Kuhn's. What the Kuhn's will do. We'll enable the Kuhn's. We'll read the instruction. It says that select the cons. So in the earlier way, like in the earlier case, I selected all the single cons by picking one by one. In this case, I will not do like that way. Instead, I will select all my single cons which are connected with each other.
I will be selecting them, you know, one click. So how to do that? So basically we have option called loop at the bottom. If you can read the instruction or if you read the description of the loop option, you'll be able to understand that the loop option is used for selecting the single cons entirely. So you can click on the loop and you can read the instruction. It says that select the cons. In this case, I will not be selecting each and every cons here. Instead, I will be selecting only one con.
It will select all the cons which are present in the loop. Let's see how it is work. So, yeah, as you can see here, we have selected only this one single con. It selected all the loop over there. So basically this is how we can select this loop option. So here it's showing us the preview of the selection. If the selection is perfect, if you find it very perfect, basically you can do the middle click. It will also show you the preview of your new surface.
So it will look like this if you are accepting this. So it is asking for confirmation. So if you click OK, yeah, we can expect this surface. Then the surface will be created over there. Same way you can use this different different algorithms to create a surface over there. Now let's check what is the feature. Basically, feature is the same as your cons option. So it will also work as same as cons. So basically you can click on loop. Loop can be activated. Select the single cons.
Then do middle click. It will also show you the preview. So, yeah, it's showing you the preview. The preview seems very correct to me. But again, if I want to check the alternative preview also, I can do that. So I can click on alternative and I can see the alternatives of my surfaces. If I find any one of the alternative surfaces is correct, I can basically accept that by clicking on OK. You can see there is a surface created over here as well. So we have seen the existing surface.
We have seen the tools. Now, what is planar? So planar is basically the same as existing surface. So if you have a plane, plane in the sense, if you have a very flat surface like this. If you have a flat surface like this and if you have a hole inside this, in that case, if you want to patch the hole, if you want to patch the surface, basically you can use the planar over there. Unfortunately, here we don't have any place where we can see the planar option.
We'll see it in the upcoming videos. So now you can understand the existing surface, fitted and cones option. So now as I have demonstrated you, you can basically do this by your own. I'll explain you how it will work. So as I have shown you these three methods, I will also show you another method called fill hole. So there is also another option called fill hole inside the cones. So let's see how it will work. If you can click on fill hole, here they will ask to select a hole or enter a hole diameter and then press select.
So we can do the first thing. We can select the hole. So I'll select this hole. So if you have observed, I clicked only one cone and then it selected entirely. Why? Because it itself asking me to select a hole. Basically, if I click only once, it will select entirely hole. If I do middle click, you can see it's filling a hole as the name suggests. So fill hole also can be used for creating a surface. That too, if you find a hole which is a circular or rectangular or any shape, you can basically use the fill hole.
Right. So yeah, coming back to here, I can again use the new fitted. I'll select this thing. So if you can see, it's selecting the entirely. But if I don't want to select entirely, what can I do? I can click on new fitted. Instead of loop, I can again go back to my entity. So what does entity do? Entity basically can select only one line on which you press a left click like this way. If I want to select only this two and then create a new surface over there, I can do very well that.
After that, you can see there is a rectangular surface there. Now I can use any option. I'll go with fill hole. I'll click once over here and then middle click. You can see there is a problem over here while realizing the new surface. So if this thing is happening, basically you should avoid this. So if you are trying different, different methods and if you're finding this kind of problems, you should go with the other. Here I will suggest you to not to go with this. If you wonder if this thing is happening, then what can be done?
There is a two method which you can do in this case. So basically you can use this universal delete option which will delete anything. It can delete hotpoint, it can delete cons, it can delete faces, it can delete curves, it can delete points, anything. That is why it is called as universal delete option. You can either select that and then delete this or else simply you can undo this. If you undo, you will be coming back to the original one step back. Here I will go with new prunes and then we'll start collecting surfaces.
Then we'll create a new surface. You can see this is also showing me a surface. This is how you can basically patch a surface. So quickly we'll finish all these patches together and then we'll move ahead with the other tools. These kind of things you can basically try making the fill holes. Fill holes you can use multiple times also. So you can select all these holes and then do middle click and then it will give you the surface in a one shot. So it is so easy.
Right. So yeah. If I can see like everything is done, then also I can check the same way how I told earlier. I can turn off these things. And then I can check with the single const. I can see that there are two more surfaces left to be created. So we'll go there and we'll try to do this. Whenever you can see the single const, just consider that the surface is open over. Right. So if you can see over here, there is a crosshatch present over here.
Crosshatch present over here. But there is no crosshatch present over here. That means there is a surface missing over here. If you create a surface here, then basically this cone and this cone will convert from red to yellow, which is nothing but double cone. So we'll create a new surface here as well. Select this cone. Select this cone. I will also suggest you one thing. So one thing which is most important here while creating a new surface. So if you're selecting two single cones, just make sure the length of the two selected single cones will be the same.
Right. So how to check that? So you need to check that in the wireframe mode. You may wonder how to convert into wireframe mode. So basically you can use control and shift together. You can see the selection with the white color. So I can see that the selection of my single cones are very proper because it has same length. You may think what happens if we don't select the same length cones while creating a new surface. In that case, basically you will not end up with the required expected surface there.
So the surface will be uneven and then it will not be desirable to have uneven surface. So here as we can see, the selection is much proper. But again, if you can see here, there is a single cones present inside. So we should not leave the single cones as well while selecting these two single cones. We should also select this and then this single cones also. So you may think how to select that single cones even in the wireframe mode. You can obviously select the single cones over here while rotating your model.
But if you think rotating a model and going there and selecting that single cones is a bit difficult for the other models. Then how to select the single cones in the wireframe mode itself? Because in the wireframe mode, we can see that single cones is clearly visible. So we can do the same by doing control shift so that we can see the wireframe mode. Understand that without wireframe mode, if we want to select any... We can click on the con only one time. It will select that con for us. But in the bioframe mode, you need to click twice. Let's say if I want to select the single con. If I click once, it will not be selected. So I need to click twice over here. So I click twice over here and it's selected from me. Same way, I will do double click on this con and it will select from me.
Now I can see the selection. Selection is much proper. Another important thing is if you have any complicated geometry and if you think like checking the bioframe mode is not much clearer due to this cross hatches and due to this like due to this unwanted double cons, triple cons, single cons, then basically what you can do, you can turn off all these cons in a one shot by turning off this. You can also turning off this cross hatch. Okay. So now you can see in the model, there is no cross hatch available. There is no single cons, double cons and triple cons visible in my model. Now if I do control shift, I can see only my selection.
This is much better way to check your selection. Only if the selection is proper, you can get the proper surface. Otherwise surface will not be proper. If I do middle click, it will show me the preview. Preview also you can check the same. So if you can see here, you can also turn off your shadow mode and then check the surface preview. So surface preview, you can see properly good. We can expect this. So click on OK. Now again, click on shadow mode so that the model can be visible. Turn on everything. Yeah. So here you can see the new surface is generated now and the cross hatch which was missing earlier that was now created because we have created an entire new surface.
So this is how we finished with that surface. There is only one surface left over here at the bottom. You can see here there is single cons. So this part is bit tricky. So if I tell you to create a new surface by clicking entirely cons from here and from here, it may not come correct. We'll check this out. So click on new, click on cons. I'll go with loop for the demonstration. I'll select this loop and I'll select this loop. You can see. So I have selected both the loops entirely. Now if I'm thinking that I can select this loop wise and then can create a surface. We'll see if it is giving us correct surface or not.
So I'll do middle click. You can see the preview. So the preview is not correct. You can see some surfaces coming outside which is not expected. If I click on alter, alternative is also not so good. Right. So I wanted a vertical surface but it shows me the horizontal surface. I can alter but no. There are only two alternatives of the surface and this is not giving us the good results. So one takeaway from here is if you have a circular cross head, sorry, circular single cons. And that single cons if you have two and then if you wanted to create a vertical surface like this case, then basically don't go with the loop method. Instead, go with the entity method.
So I'll go with the entity method. I'll select this con. I'll select this one. So you can see the length of the selected cons are not same. Basically, the surface preview will also not come properly. You want to see for you. So do middle click and then try checking the surface. You can see the surface is coming in this manner. That is the reason why we should select both cons with the same length. So again, I'll do control Z for undoing my task. Now, what I can do, I can try selecting the entities which is nothing but cons.
In a manner that the length will be same. So here I can see the length is same for me. So I will not create a surface entirely. I will create a surface in two shots. First over here and then second D over here. So I'll do middle click. You can see it's showing me very nice surface. Click on OK. In this case, I can either go with phones and I can also go with the fill-on option. So this time I can use loop and I can select everything. You can see the selection as well. Do middle click and then have the surface.
This is how you can basically finish your model. So now if I go and if I do geometry checks over here by enabling all these things, if I execute, you can see the status is all OK. That means I don't have any error at this point of time. You may wonder this is correct. And let me start with matching. As I told you earlier, in CFD analysis, basically our surface should be closed so that we can go with the volumetric match. So we will be learning what is volumetric match in the later stages.
But for now, just consider that we should have closed model with us in order to do volumetric match. So here we can see the model is open from the bottom. Right. So here we can say the model is open. So we need to patch that more. Right. So we will be thinking how we can patch this model. So you may wonder, only if we have single cons, we can create a new surface. So that is wrong. Even though you have double cons, you can again create a third surface over there.
Right. So basically there will be one surface over here, one surface over here, and the third surface also you can create by picking this double cons away. I will show you how. So do the same way. Click on new, select this, middle click, then click on OK. It will create a new surface there. You can find here there is a triple cons formation happening over here. I told you the reason why it is forming a triple cons, because here basically three surfaces are joined. Right. So this is one surface.
This vertical one is the second one. This horizontal one is the third one. So here, as the three surfaces are joining together, it's forming a triple cons over here. If you are not clear with the three surfaces, I will also try to show you. So I will isolate the three surfaces. So just see how I am isolating. For isolating anything, we can basically use I0 option. So I0 option is used for isolating the surfaces. So whatever surface we will click on, that surface will be isolated.
We'll see how it is working. Click on the I0. Click on this surface. So you can see it's selecting entirely. I wanted only this smaller surface, but it's selecting entirely. Then what is the reason for that? So basically the reason is the PID region is activated. Right. So if you want to select any one surface, basically you should select the entity mode, not the PID region. Right. So press escape. Do the same again. Click on I0. Enable entity mode. And then select the surface. So I have selected one surface.
Only one surface is getting selected. So if I want to isolate this also, I can select that as well. Then I will be isolating this and I will be isolating this. So, yeah, I wanted to isolate only this three surfaces so that I clicked on only those three surfaces crosshatch. Now, you may wonder why it is not isolating. So it will isolate only if you do middle click again as a completion. If I do middle click, I can isolate the things which I have clicked on.
So here you can see the three surfaces. One surface is this, one is this, and one is this. In total, you have three surfaces joining at this point of time, at this location. So that is the reason why it is forming triple cons over here. So this is the reason why the triple con is forming. This triple con you should not consider as error because here basically three surfaces are joining. If you want to solve this error, basically you should delete any one of the surfaces and it will again convert into double cons.
But here we are not allowed to delete any wanted surface. So just understand triple cons is not an error. But you should always go to the location where you have triple cons and you should check whether the triple cons are needed or not. In this case, triple cons is actually needed because we want all the three surfaces together over there. So we will be keeping these triple cons. Now, again, there is another tools at the bottom. So I will try to explain you those tools here.
So we have checked the I not option. Right. So we will check this and option also. So what does this and option will do? So and option will try to enable your neighbors. Right. So let's say here there is a double con. Right. That means there will be again a surface over here. That is the only reason why. Double con, right? So, if I click on AND and if I click on this double cons, basically, I can have a neighbor surface. Again, if I click on this, another neighbor, click on this, another surface, like that way, you can have all these neighbor surfaces one by one.
Let me do undo. So, this is the case. So, this AND option, you can use for taking out your neighbors. The same thing you can do with the help of neighbor option also. There is a neighbor option present over here. You can see there is a small drop-down arrow over there. That means there is something inside the neighbor. If you want to see what is inside that, you can basically long press it. I'll long press it. You can see there is two options inside that. First is first level and the second is the OR. If I click on first level, what it will do? It will try to show you the first level of your neighbors.
That means whatever is present in your screen, the surface which are connected with these particular things which you can see in your screen, it will try to make it visible for you. Let's see how it will work. So, I'll click on first level. You can see it's showing me the pair of surfaces which are connected with the visible. visible surfaces. This is how the neighbor first level will work. Now, what does this neighbor OR will do? Neighbor OR will try to show everything. That means it will visible all these entities which are present in your model.
So, if you click on all, everything will come up like this way. There is again another method to show everything in your screen. So, I'll do undo, ctrl z. So, this time I will not go to neighbor OR. Instead, I will go to all option over here. So, if I click on all, everything will come up like this. So, this all option and this neighbor OR option will be same. Similarly, AND option and neighbor first option will be same. You may wonder what OR option will do.
If you click on OR, if you click on any one of the surface, that surface can be isolated directly. Okay. So, yeah, the takeaway is OR and I NOT option is used to isolate the surface. The only difference is in OR, if you click on the cross, if you click on the surface, that surface will be isolated directly. If you are using I NOT, you need to click on the surface, middle click, and then you need to do middle click again in order to isolate. But in OR, you can basically click only one time and it will be isolated.
I'm taking everything back here. So, you know what is OR, what is AND, what is I NOT. Now, we'll see what is NOT option. Opposite to AND, the NOT option will work. So, if you enable NOT option and if you click on any cross-hatch, that means if you select any surface, that surface is going to be hidden. We'll see how it will work. So, I have enabled the NOT option. Now, I'll click on this cross-hatch. You can see that surface is hidden over there. So, NOT option is used to hide the surface over there.
Basically, you know everything. So, there is also one more thing called as invert. So, how does the invert will work? So, let's say I am isolating this top surface over here. Now, I have isolated this thing. But if I want to see what are the things which are not selected or not visible over here. That means, what are the surfaces which we have hidden. If I want to detect those, I can basically use invert option. Okay. So, invert option will invert your view. So, in this view, if I have this one surface enabled, if I click on invert, I can have every surface available in my screen except this particular surface.
Let's see how it will work. Click on invert. The previous surface was hidden here. And apart from the previous surface, every, each and every surface are visible in this. So, this is how the invert option will work. I am showing you this visibility tools one by one. So, basically, you can understand how it is used and what is the importance of each and every visibility tools. So, this is regarding your topo cleanup. So, this is the way how we can do topo cleanup. So, this is all for this class.
We will meet in the next class and we will see how to match this. How to give the target length. What are the elements we can use for the mesh. How to match, how to match, and then the other mesh improvement tools in this mesh diagram. So, this is all for this class. We will meet in the next sessions. Thank you guys.
Part 2
Hello guys, welcome back. So in the previous class we have seen about this topo cleanup for this particular model. So for the topo cleanup we basically solved few single cons which are present at some location in this model which shows that the model is open not closed one but as we discussed in CFD applications we want model to be closed. So we have done this topo cleanup part. Now we will be checking if something is wrong or not. So basically in order to check that we can do few steps. So there are again some alternatives.
So always we can go with the text over here in the text manager that you can go with the geometry text. You can make enable this visible option and then you can execute. Before execute you just check what are the things you will be checking here. So turn on the things if it is turn off and if you want to be checked for that criteria as well. So you can always check these peak marks before going with the actual text. So all this checks seems fine to me. So I will now execute this. So it's showing me four errors which is nothing but triple cons. Right. So as triple con is also turned on over here it is detecting that your model is having some triple cons.
Right. So as you are there in the checks manager. Your model will become transparent and it will try to show you or to highlight you the errors. If you select those it will select the preview where exactly you are having the triple con. So here we have discussed in the previous class that here there are three surfaces joining over there. That is the reason why there is a triple cons present over there. Right. So we discussed in the previous class regarding this triple cons and we also discussed that this triple con is actually not an error but just a warning that we are having triple cons over here.
So we should basically go there and check if actually there are three surfaces are joining at the common age or not. If yes then just check if all the three surfaces are required either we can remove one of them or not. If no then basically we can have this triple cons present in our screen. So yeah we have checked that the triple cons which we got as an error which is required over here. So we will not be worrying much about this. So this is one more of checking the geometrical errors or we can say the single cons and triple cons.
There is another alternative method for doing the same. So at the bottom if you can see there is a visibility tools. So as we have seen in the week one videos that is often called pairing points. If we turn off that it will basically turn off the hot points. Also there is single con double con and triple con visibility options over here at the bottom. So you can disable those as well. Now I want to check where is my single cons present in this model. Ok so in order to check whether my model is having any single cons or not I will only enable the single cons and I will disable the double con and the triple con.
If I disable the double con and triple con basically only the single cons will be present and the crosshatch will also be present. So I will turn off the crosshatch as well. Ok so now my model is having only single cons. So now I will go to the wireframe mode and I will turn off my shadow mode just to see my model in the form of wireframe mode. In the wireframe mode I am not able to see my single cons present. Ok so let us check for the double con.
So I am turning off single con as well. I am turning on the double cons. In the double cons I can see these are my double cons. Actually in any model we expect double cons and we never consider double con as a error. So that is fine. We will check with the triple cons. So triple cons is basically present at the bottom. This we have already discussed. So we are also not much worry about this triple con. So this is how you can basically check your particular single cons, double cons or triple cons individually by turning off crosshatch, by turning off the other cons and by turning off the shadow mode.
So this is how we can basically check. So this is regarding our checks for the single cons and the other errors. Now we will start moving towards meshing for this particular model. But before that I would like to show you few things in this model. So when the model is designed by any design engineer, he may create a lot of small small surface in order to capture the features and in order to maintain the shape of this particular model. So there will be a lot of chances like you will have a lot of small small surfaces like this in your model.
And we are not supposed to have this very small surfaces present in our screen. So we are not supposed to have this kind of smaller surface in our model because those kind of small surface will interfere while doing meshing. So how it will interfere? So basically if you can check the distance between these two lines, which will be very small. If the distance is very small, if you are going to fit a larger element over here in the surface, basically it will not fit. So that practice is not good.
So what I mean to say here is your surface is smaller than your match element length. And basically it will not be a good practice. So just think if you are planning to give target length as 5mm, just check everywhere else whether you are having two lines near to each other less than 5mm distance or not. If yes, then basically try to avoid those. You can maximum, you can try reducing this nearer lines as much as you can. Now you may wonder how do I do that?
So basically by removing these cuts, we can basically remove the restriction of this smaller surface. So click on cut and do right click over here. If you do like this, if you can see the line is gone from here and it's forming an orange color line, which is nothing but a history of a line. So it's showing that once upon a time you were having a line over here, which is basically now removed. So same way you can remove the lines which are very near to each other and which you think which are not supposed to be present there.
You can basically remove those specifically lines which are there in one common surface, which is having no significance. You can try deleting those. So like this, you can zoom in and then you can think of deleting those lines. Once you think you are done with your this particular process, you can basically go with the match option. Before matching this, I would like to tell about PID manager and I would like to tell about PID. Make sure whenever you are using answer, you are there in the PID mode from the bottom.
So this is the PID view. So whatever elements you can see in your screen elements mean surface. So whatever surface you are able to see in your screen now. So that is in the PID mode. Right. So that is the option called PID manager at the top. If you open that, you can see there is only one PID assigned as of now. And that PID named as shell property. So this is the name of the PID. The thickness of this PID is 1 mm. And then material ID is 2.
We will see what is this thickness, what is this material ID afterwards in this course. For that, we just try to understand how to assign the PID and how to create a new PID. We will see if this place is just a nice thing. Thank you.
Part 3
So in order to create a new PID, you should basically do right click, new, PShell, PShell. So if you follow the steps, basically one new pop-up box will come up where they will ask you to write a name for that. So we'll basically create PID for Outlet now. Same way, we'll create few PIDs now and then we'll assign together. You can also change the color of your particular PIDs by double clicking on the color box and then selecting colors from this palette. You can click on OK. I'm just giving you some random examples. Like this way, you can always assign your colors by double clicking on this palette and then selecting your desired colors. Now as you have created new PIDs, now it's your turn to assign the PIDs.
So how to assign the PID? So in order to assign PID, let's say I need to assign this Outlet PID now. So I will do right click over here and we'll go to Apply and I will select the crosshatch of a particular surface which I need to be assigned as Outlet. So I'll select like this, make sure I'm clicking on the crosshatch in order to select the surface and I'll do middle click. Same way, I'll do for the other two. So Inlet and Outlet are now being created.
Now I need to assign this PID for this body, which is nothing but a place of my particular wall. In order to do that, first of all, we should isolate this. So if I hide this Inlet and Outlet PIDs, which are already assigned, you can see there is something in that is my casing. So there are a few components available inside my casing, which I don't want to assign as body. I want only the Outlet surface to assign as body. If you want to assign this PID body, make sure you are isolating the surface which you want to assign in the body PID.
That means I need to isolate this outer casing alone. So how should I do that? Basically, as you guys are very well aware of, our option is used for isolating any kind of surface. So I need to click on OR. So there are a few things which I need to tell you about this selection. So for selection, we have a few methods over here. So we have entity, we have PID region. Also, if you click on the drop down button, we have a lot of other options as well.
So you may wonder what is this PID, PID region, macro region or macro area. So these are the selecting tools. So if you want to select anything, we can basically use any one of those. Let me show you with the NOT option now. If I am there in the entity mode and if I click somewhere on any one of the surface, only one surface is getting hidden as I have selected the NOT option. Right. So on whatever surface, I'll click this, it will try to hide that surface alone. But what if I want to select a surface more than the entity? That means multiple surface together.
So there are two or basically three options. So PID. So if I have enabled the PID selection, basically it will try to select PID-wise. PID-wise in the sense in Properties Manager, I have created three PIDs as of now. So it will try to select the PID-wise. So I have this light brown color, this purple color and then this green color PIDs. So if I click on over here somewhere, it will try to select all the entities which are there in the light brown color. Similarly, if I click on this, it will select only that surface.
So the takeaway is, it will try to select the surfaces PID-wise. So it can be multiple surface or it can be only one surface depending upon the assignment of your surfaces in that particular PID. That is for PID. Now, if you go to PID-region, what it will do? It will try to select the surfaces, not PID-wise, but PID-region-wise. So PID-region means it will try to select your surface and the selection will keep on go until you have some break in between your two components. What do I mean by that? So that we'll discuss now.
Now, let's say for example, we have enabled only one PID, which is number 36, which is my disassembly. In this assembly, as I have seen earlier, if I am going with PID, it will select everything which is there in the same color. But now, if I choose PID-region instead of PID, it will try to show me the selection only on the outer side, not the inner side. So we'll see that. So if I click over here, you can see the selection is happening only on the outer side, not in the inner side.
That means some connection is breaking in between this outer and inner surface. You can see there is a gap present over here. So that gap is not allowing the selection to go beyond the selection. And that is the reason why it is most useful if you want to select anything within the PID. Just like this, now I will use my OR option just to isolate my outer casing and then we'll assign PID for my body. Go with OR option and then I will select the outer casing alone.
Always I will check my selection by rotating my model or by going into wireframe mode by control and shift together. So I have checked that everything. So the selection which is made by me is pretty much fine. This is also expected. So I will middle click and I will isolate P only outer casing which is nothing but body. Now we can very well assign this body PID to our visible parts. So right click, apply, make a box selection and then middle click. So this is how I finished with assigning PIDs for a few parts.
Let me hide this few parts. So these are all the PIDs which I have created and assigned also. Now it's done to assign the PID for these different, different other remaining components. So now I will try creating a new PID for spring and we'll hide the same. Right click. New, Pshell, Pshell and then get spring. Create PID for the base. So let's now try assigning this PID one by one. So let's start with the base surface. So I will right click. Click on apply. Go to the bottom side.
Enable this entity mode. Because now I just wanted to select only one surface, not multiple surface. So I will go with the entity mode, select this, middle click. As this is assigned, I will hide that. Now let's go with the spring now. Right click. Apply. Here in this case, if I choose this entity mode and if I select any surface, only one surface will be selected. So I don't want that to happen. But I will deselect this by right clicking that. I will try with PID region over here.
And we'll see how it is selecting you. So you can always check your selection by zooming in and checking very carefully. All these required surfaces are selected or not for your PID assignment. So this is how you can check. Also you can check by enabling your wireframe mode with the help of control and shift. You can always do control and shift or else you can always turn off this shadow mode. And you can check your wireframe mode from the bottom to the bottom. So here we have confirmed that the selection is much proper.
We can do middle click and then just assign the PID. Once it is also done, you can hide that as well. See what other parts are left over here. So you can find that the valve head is present at the top and the other surfaces are also attached with that. So now I have few options if I want to assign this PID for the valve head. So if I try applying that by using this PID region, we'll see if it is selecting everything. Yeah, so it's selecting everything.
We don't want to select everything once at a time. We only want to select the top surface. Then what should we do? In order to select only the top surface, either we can go with the entity more and then select it one by one like this way. So this is one matter which we can do. Or else, the other thing which we can do here is, we can try hiding this particular surfaces and then we'll try selecting with PID region. See how it is working. So before that, I'll also like to introduce the lock option over here.
So just consider that if I have only this particular... ... And if I click on all, basically everything will come together. Right. So if I don't want everything to come together, even if I press on all, then I need to apply lock over here. So if I click on lock, basically this window is locked now. Now if I click on all, nothing will come. Even if I hide a few surface by using not option with entity, if I hide a few surface like this, and then if I click on all, everything will come together, whatever we have locked.
So just understand, if you are locking something, basically the view will be locked, and whatever things are present in our screen, it will consider only those parts, and then even if we click on all, not everything will come, but only the parts which we are locked, that only will come back. So this lock option is very much useful. You can release the lock, and then you can click on all, and you can see everything is coming up again. So that is the function of the lock option. So we will again hide all this assigned PID, and we will work with this.
So we were discussing about how to select only the top part by using PID region, because if I am selecting PID region now, it is selecting fully. So in order to not select everything together, I need to make some break in between. So if I can see here, there is a small surface which is joining this top surface with this bottom parts. So I will try to hide. Again, I will use lock option, because I will be needing it. So I will use not option now, and then I will try to hide this surface and this surface.
Okay, so you can see I have hidden my smaller surface, and then I break my connection there. Now as I have break my connection there, I can basically use PID region option, and then first of all, I will press escape in order to leave all those functions enabled. Then I will go with wall head, right click, apply. Then I will again go to PID region. This time we will see if it is selecting everything or not. If I click here, it will not select everything, because we have lose our connection over here, by hiding the surface.
We will do middle click, and it will also assign over here. So let us hide that as well, and then we are left with only this part. This part is nothing but the shell property, which is your particular by default PID card. So you can create a new surface named as column, and then assign that PID for this thing as well. Okay, do a box selection, and then middle click. Like this, you have taken all these PIDs assigned very well, with different colors you can see.
So this is how you can assign the PIDs, and then you can think of matching this. So this is all for this class. In the next class, we will see how to assign mesh length, and then how to mesh this component one by one, by taking 1.1 PID, separated in our screen. So I hope you understand all of this. If you have any doubts, you just consult your support engineers, and take the help in order to solve your doubts. This is all for today. We will meet in the next class, and we will discuss further.
Part 4
Hello guys, welcome back. So in the previous class, we have seen how to create and how to send PIDs for different different components. So we tried for this many components and here we can observe that. So there is still this 36th number PID which is nothing but our by default parent geometry PID is still existing with the pulp, right? So there is some surface which is missing still. inside this 36th number PID. So even though we have assigned and we have created this many PIDs, still something is left there, right? So we should check that. So what is that? So basically you can do one click over there just to see what is that. So also one more thing. So there is an option called PIC over here, right? So currently it's enabled. If I click on that, it will be disabled. So if it is red, that means it's enabled, right? So if I want to check what is my PID for this, then I can basically click on that and it will try to show me the highlighted PID in my PID manager. Same way press escape and select somewhere else over here. It will select me the particular PID in the PID manager. So this is how I can with the help of this PIC option, I can check which PID is where.
Similarly, you can do the opposite also. You can click on that and then you can see in the model where is your particular PID. So we can always do right click and then click on show or show only. If you do show only, it will show me only that part. And if we remove this selection by clicking somewhere over here, the selection will remove and we can be able to see this particular surface. So now it's very difficult to understand what kind of surface is this. So if you have remember, we have hidden one surface just to break the connection between the pressure wall head and then column.
So that now it's our task to assign this PID either to the head or to the bottom column, right? So if you are not aware of which is the surface and with whom we should connect this, you can always use this neighbor first level option. And then you will have first neighbors of the visible entity. So this is the light brown color ring which we were seeing in this particular display. And these are the neighbors for that. So basically, now it's our task to check which PID we should assign now. So we can confirm that this pink color PID is pretty much fine for assigning this smaller surface.
So again, check which is this PID. So click on this and this is column PID. Fine. Then if you want to update any PID surface in that particular PID, you can basically do same thing. Right click, right click, click on apply, select this surface, also select this surface, do control shift or turn off the shadow mode just to see the selection. So selection is pretty much fine. So again, turn on the shadow mode and then do middle click for executing this. You can see the PID is now updated and this surface is added to this PID number 29.
So you may also observe here that the bulb is partially turned on, partially turned off. What do that mean, right? So basically, you are aware of if bulb is fully turned on, you can basically see all the parts of that particular PID. The bulb is totally turned off. You can basically, you cannot basically see any kind of surface for that particular PID. But this is something in between those two situations. So partial bulb is turned on and partial bulb is turned off. So basically, we can say that partial surfaces are visible and partial surfaces are hidden now.
That is the reason why the bulb is partially turned on. So if you want to see everything, it should do the same thing. Select both of them by pressing control and then do right click and then click on show only. Right. So if we click on show only, it will show us everything from that two particular PIDs and we can see the bulb is now fully turned on. So this is just another concept which you can basically learn. So you do not worry when you can see the partially turned on the bulb.
So this is regarding PID assignment and PID creations. So I hope you guys are now very well aware of how to create PIDs, how to assign PIDs and then how to change the color of this different different PIDs. Right. So that is one thing. The another thing is this 36 number PID. If you can see still the bulb is showing on. But yeah, it's not turning on even if I'm clicking on that. That means nothing is present over there. Right. So basically I should delete this PID because it has no significance now.
So just to confirm before deleting, what I will do, I will do right click and we will click on show only. Just to check if I have anything in my screen or not. So yeah, I don't have anything for my this 36 number PID. So now I can think of deleting this by right click and then click on delete. So you can read the error that selected IDs is used by deleted phase and cannot be deleted. So that means you must have deleted something and then due to that it's not allowing you to delete that particular PID.
But you have also checked that there is no surface present. If I do show only, that means this is obviously a dummy PID and I don't want that. So I need to like forcefully delete this. So if it is not deleted by using right click and delete, there is another option called compress. So this compress option is used to delete your any particular PID permanently. Before using compress, I would like to show you some option called undelete in the phases. So I have turned on all.
There is also another option called fit in. So if your model is, let's say, hidden somewhere over here on the sideways and you are not able to find that out even though you are pressing all. And basically you can click on fit in and there is also a shortcut for that, which is F9. Click on that. You can basically check that all your models are coming up in your screen. So this is very important tool just to make sure everything is there in your screen. So I was talking about this undelete option.
So there is option called undelete in the phases. If I click on that, it will show me the deleted surfaces. So you can see the white color selection and the green color cross edges, which is showing me this surfaces were deleted by me intentionally to demonstrate you this top open. So like this way, you can see those. If you think, let me retrieve that back. I want that back. What is the steps for that? So you can basically click on the cross edge. You can see the cross edge is becoming more bright green colored as the time.
That means the selection is happened. Also, you can do control and shift. You can see this is selected by green color. The rest of all are selected by white color. So white color is showing the undelete surfaces. Sorry, the white color shows the deleted surfaces. And then the green color selection is showing me that I have selected the surface just to retrieve back. So I'll do middle click and you can see the surface is coming. You may wonder why these clickings are happening. So basically, there are two overlapped surfaces are present there.
One is this basically outlet, which is pink color, which you can see over here. And the other is this 36 number PID with light brown color, which can also be visible over here. If you want to check that, you can use this bulb and you can see. So this is how you can basically check your overlap. Whenever you are seeing the glitchings in any of the surfaces, just understand that there is an overlapped surface present over there. And there are two mixed colors while in the glitching will represent the PID color of that particular two surfaces.
Just like pink and then light brown color. Also, there is another method to check your overlap surfaces. So basically, if you are doing anything undelete, if you are using undelete option just to retrieve any deleted surface back, there is also mandatory to use topo option at that region just to view connectivity. Because undelete option will only retrieve back your surface, but it will not connect your two surfaces. So in order to connect the two surfaces, you should use the topo option. If you use topo option, you can see there is a triple con present over there.
We all are aware of that. Triple con is there only if there are three surfaces joining at a particular edge. We all are aware of that. In this case, we can see that at this particular age, there could be three surfaces joined together. So whenever you are able to see the triple cons, don't consider this as an error. Instead, just check whether there are three surfaces joining together or not. If yes, then check all these three surfaces are required or do you have any overlapped surface.
In this case, also, I will check that whether this triple con is needed or not. So I will try to hide my each and every surface near to this location and we will see. So I have hidden this surface. So that means there was only one surface present. Still, if I have only one surface here and one surface over here, I should have double cons over here, right? But now I can see there is a triple con. That means something is wrong with this particular surface.
By checking like this way, I can consider that there should be some overlap. And then also I can check these greetings and I can confirm that there should be some overlap present over there. And then I will try deleting any one of them. Okay. So basically, I will try deleting this cell property, which is nothing but this particular surface. So I'll try right click and then we'll delete. See, so that is gone now. Also, you can see over here the PID, which was earlier showing some error, like selected ID is used by a deleted face and cannot be deleted.
That error is also now not showing up and it's saying that 18 items are deleted. So this is how you can basically use this undelete option and then delete everything together. So now we have all this required PID in our screen and then now we'll very well start with this meshing. So let's get started. So before meshing, as I have discussed earlier, you should assign the mesh length first. So click on mesh length, go to parameters, select this. Give mesh length as, let's say, 5 mm.
Okay. Go to parameters. Select this, give 5. Go to match parameters. Write 5 over here. Go to quality criteria. And then for now, just understand, if we are giving mesh length 5, we can give minimum length as 3, maximum length as... Sorry. Minimum length is 3, maximum length is 7 for that. So earlier you may saw the error coming up, bad combination of target length that is 5 and quality criteria, max length is 3. That's why we changed the maximum limit for our particular model from 3 to 7.
Now this thing, this error should not come. If I assign the mesh length again, you can check that. So no error is coming up, right? So, also understand why the error is coming up. We were giving the mesh length 5 over here. But in quality criteria, the minimum length and maximum length was not obeying the target length, which is 5 mm. So, this much task we need to do before going with the mesh. So, always remember, we should give mesh length to the 4 locations. 2 in the length option, which is parameters and macros.
1 in this mesh parameters. And then 2nd in this quality criteria. Right, so, also give minimum length as 3, maximum length as 7. So, these are very basic quality criteria. There are a lot more quality criteria present in our quality criteria table, which we'll see on the later stages. For now, just consider that before starting of mesh, just give your quality criteria in mesh parameters and quality criteria for target length, minimum length, and maximum length. So, as we have given all these quality criteria, now we are very well start with this particular matching.
So, as we have given the quality criteria, now we will start with the matching. I would like to show you the matching one by one. You can also do matching by one shot. So, basically, you can use any one of these algorithms. Free, batch mesh, spot mesh, GFT, or any other base mesh option. You can use any one of them. I'll basically use this spot mesh. If I've clicked on that, you can see the element type is mixed. Right, so, we are supposed to match with 5 elements, but it's showing just mixed.
So, I'll also suggest you to check this option list every time, once you are selecting any one of these tools in the match mode. So, this will give you an overview of particular elements or the type of the elements. So, now, just understand why this makes this coming up over here. So, here, in the match parameters, we have only even the target length, minimum length, and maximum length. But we have not assigned this particular element type over here. So, we should assign the type over here in the trial.
So, as we have assigned the type of the element is tria, now we can check with the spot mesh. If you click on that, you can see the element type is changed from mixed to tria now. So, understand that each and every tool, if you are clicking over here, it will show you the options list for each and every tools. And in that options list, it will show you the element type, target length, minimum length, and maximum length, also the match parameters. So, make sure whatever you are giving the match parameters earlier, that will be selected by default by using any one of these tools.
So, this is a very important concept, why you should give these match parameters before starting off your match. Because that will decide your each and every tool's option list. So, if you are not giving the match parameters, probably, you will have mixed instead of tria, or you will have different target length, which is by default given from the answer software. So, the main takeaway here is, always give these match parameters, quality criteria, and then length before starting off your match. So, once we confirm that, we can basically start with the meshing.
So, click on spot mesh. Now, we will try to mesh this outlet one. So, we will try selecting this by box selection. If you can see, it is also selecting the backside surface. So, in order to deselect, I will do right click over this corner. Then, I can say, the selection is pretty much fine. So, as I have selected this, I will do middle click. So, this is how I mesh a surface. This is very easy. So, just like this, I will go one by one, and we will mesh everything.
So, just understand, in order to select both the surface together, what I did, I clicked on this line, which is nothing but double cons in the topo mode. I clicked on that line, just to select both the surface together in one shot. So, understand that, if you want to select two surfaces, basically, select a line which is common for both the surfaces. Same way, I will mesh everything. So, I can do mesh like this way also. And, if you think, you can also try some other way of matching this.
So, what I will do now, instead of matching surface by surface, which is nothing but entity by entity, now, this time, I will try matching PID-wise. So, I will click on here, and you can see, it's selecting radicular PID for me, which is nothing but body. So, it selected everything. I will do middle click, and it will mesh for me. So, this radicular components are matched now. Also, I will go with PID, and then we will select this con. But, you can consider, I selected this con, which means, it will also try to select two PIDs.
One PID for this, one PID for this. That is why it's selecting everything. So, now, what I will do, I will do the same. I will do right click for this PID, and then that PID will deselect, and I will only left with this top PID, which is nothing but inlet PID. I will click on that, and it also will show me the meshed surface over there. Similarly, for this, always, after selecting, just check your selection. If your selection is like this, then press escape, and if you find some difficulty while meshing this, I will also suggest you one thing.
Click on spot match, PID. Okay, so, we'll do one thing. We'll isolate this particular base surface first, and then we will match that accordingly. So, click on show only. Now, we have only this surface present in our screen, which is nothing but a PID. Now, we'll go spot match, and then do visible. Only this surface is visible. That means, only this surface will be meshed for me. Click on all. Now, see, from outer side, we have meshed everything. Let's roll the inside. So, for my ease, what I will do, I will try to hide all these surfaces, which are meshed.
Because I don't want to see those, as it is already meshed. So, what I will do, I will use this pick option. So, what I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will do, I will Thank you.
We'll select over here. We'll click over here and it will show me the PID name. So, inlet. So, I confirm that inlet is matched. I'll hide that by turning off the bulb. Same way, either I can use this peak option just to identify which PID I should turn off or else if I am very well aware of the name of the PID, I can directly go and then I'll hide the PID from the PID manager itself. So, body also is done. Outed is also done and base surface is also done. So, we are left with only this many. So, we'll see how to work with this particular PIDs now.
So, let's work. Okay. So, first of all, till now we have not explored this lock option. So, now we'll explore the lock option also. So, there is an option called lock at the bottom. If I use lock, if I click on that, that means my preview, whatever I can see in my screen with this 1, 2, 1, 3 PIDs. So, this view is getting locked now. So, now if I click on all, so everything will not come because I have locked just before that. Only if I release the lock and if I click on all, everything will come again.
Okay. This is very much interesting tool which we can basically use. Right. So, also, we can lock that. Once we lock that, we can work with this particular remaining entities. So, again, go to the spot match. Before that, I can also isolate my valve head. Click on show only. And then go to spot match visible. Okay. It will match for me. Click on all. You can have only this many parts. So, now you just understand why I use this lock option because I don't want each and every surface come again and then interfere in between. That's why I locked it so that I can isolate these things one by one.
And we'll match that accordingly. Right. So, this is how you can match. There is also one more take away over here. I'll tell you that later on. First, I'll finish with all these remaining surfaces. So, I'll try matching this. So, click on spot match visible and then have this. All right. So, I was talking about some take away here. So, the take away is if you have a very smaller surface or very smaller side of your surface and that surface is about to mesh with the given quality criteria or given target length which is more like which is large compared to your particular component size then basically this thing will happen.
So, in this particular spring we can see. So, in this particular spring we can see the mesh length which is 5 is pretty much larger for this component. So, you can see here. What I will do. I will do undo here. I will try to measure the diameter. So, basically the distance between these two nodes which is near about 3.4 mm. So, just consider if the diameter is 3.4 mm, how can you mesh that spring with the help of 5 mm, right? So, if you have a very smaller surface and then if you are trying to mesh with a very larger surface basically that won't happen.
Right. So, we can see that the quality criteria or the target length which is given to us should be such that it will justify each and every components from our model. So, no single component should face this kind of difficulty. Just to understand that I gave target length as 5 mm. Just to let you know that this thing can also happen if your target length is not pretty much fine and still if you are asked to work with that. So, this is a main takeaway. So, again I will do redo and then we will match this again.
Yeah. So, I matched this. You can see the problem which is coming up over here. This is just to let you know guys. Not only the spring but also you can consider this wall head, right? So, the wall head is also not having good surface quality over here. You can see. So, the quality is always depends upon the size of our target length. So, if the target length is small, basically the element size will be small. You will have more number of elements than this particular element.
And then you will have nice accuracy while meshing and also your geometry will be obeyed by your mesh elements. We will explore that how the target length is affecting our particular geometry. So, in order to explore that, what I will do now, I will isolate this my particular wall head alone or option with PID. We will click on that and I will have only this thing available. Now, for this, what I will do, I will try changing my target length. Earlier, I used 5. Now, I will use 1 mm as my target length and we will show you the difference.
For 1 mm target length, my minimum length should be 0.5. Maximum length should be 2. Click on OK. Go to Mesh Parameters. Update your target length and your quality criterias everywhere, wherever you are finding your... Sorry. Let's wait for some time. So, we need to change our quality criterias and target length from everywhere. So, click on 1. So, give it as 1 and then minimum length as 0.5. This as 2. Click on OK. Length. Diameters also 1. And macro should also be 1. Once I finish with these things, I can basically start with my matching.
So, spot match and visible. You can see my 1 mm is so smaller than 5 mm. You can see the number of elements is now increased. Yeah. So, one more thing. You can always check your element number over here on this side. So, earlier, the elements was very less. I can say the 1 5th of this particular element. And now, in this case, the elements are increasing to 5th time. So, elements are increasing 5 times than the earlier one. As the target length is reduced by 1 5th.
So, you can check the surface quality now. And you can compare with the earlier cases. So, earlier, the surface specifically at this fillet region was not so good. But now, in this case, the surface is pretty much fine. Because we have reduced the target length. And then, we increased our number of elements to capture this particular surface. So, this is very nice takeaway over here. If I click on all, you can see the difference between this two match length. Right. So, I will do the same.
This time, I will also show you the effect of this target length for this particular springs. So, I will isolate those. In order to give match over here, first of all, I should erase the match. In order to erase the match, I should use erase, make a box selection, and then middle click. Like this, it will erase for me. Give that length as 1 mm. Macros as 1 mm. Also, check your match parameters and quality criteria. Those are also 1 because we have not changed after that.
So, this is pretty much fine. Now, we can directly go with spot mesh and visible. So, you can see the spring is captured with a very nice feature than the earlier case. Right. So, in earlier case, as the diameter was 3 and the mesh length was 5, it was not able to capture properly. But in this case, the mesh length is sufficient. So, this is how you should decide your target length by considering your smallest component in your model and then apply the same mesh length to that particular component.
So, it's not like you should only have one target length for entire your assembly. You can also have different, different target lengths for your different, different components based on the size of the components. So, in this case, I have done the same. So, these two parts I tried showing you. Smaller mesh length and the rest of the other, I showed you with larger mesh length, so that you should understand the effect of this particular mesh length and the target length. So by now, I hope you guys are very well aware of how to mesh a component, how to change the mesh length, how to change your minimum length, maximum length and target length from all these quality criteria.
And then, how to isolate one by one surfaces and then we can mesh that with different algorithms in the mesh generation and how these target lengths are being decided by the R&D people by doing so many experiments. So, as a CE engineer, we should understand whether the target length given to us is compatible with all the components or not. Basically, it should be because R&D people will decide that by doing so many experiments with so many different tools. Right, so this is how you can basically mesh any kind of assembly or any kind of components, just like this pressure wall.
So, I hope you are aware of how to mesh, how to assign PID, how to create PID and then how to mesh that by now. So, if you have any doubts, you can contact your support engineers and get your doubts clear. So, this is all for this class. We will meet in the next class. So, thanks for the joining and we will see you in the next class.