Wiring harness design in CATIA V5 - 3D modeling Week 5 & 6 Challenge

                                                     PROJECT-9                                   …

                                                  Week 10- Assembly Workbench OBJECTIVE: To create quick return mechanism and CV joint parts in part workbench or generative work bench and assemble…

                                                           PROJECT-1 Aim- To route the wiring harness on given Engine and flatten view drawing in CATIA V5. Objective- The…

           WIRING HARNESS DESIGN IN CATIA V5 - 3D MODELLING WEEK 7 CHALLENGE   AIM- To prepare a flattened-view of a previously created harness assembly OBJECTIVE- The objective of this project is to create a flattened-view for a harness assembly and then place it on the drawing…

       WIRING HARNESS DESIGN IN CATIA V5 - 3D MODELING WEEK 5 & 6 CHALLENGE AIM-  Route two electrical harnesses as per the given layout and interconnect them as a single harness assembly and then check for bundle continuity, bundle warnings, and then give annotations to the final harness…

                   WIRING HARNESS DESIGN IN CATIA V5 - 3D MODELING WEEK 4 CHALLENGE AIM:  Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering…

                      WIRING HARNESS ROUTING & PACKAGING RULES WEEK 3 CHALLENGE  AIM: To solve the above assignment questions and define the necessary electrical properties in the respective workbench.   OBJECTIVE: To download the P-Clamp CAD data and…

                                                  CORE AND CAVITY DESIGN: AIM:Create the Core and cavity blocks for the switch bezel designed in the earlier challenge.  Introduction: The plastic…

                                      WIRING HARNESS DESIGN IN CATIA V5 INTRODUCTION: Wiring harness is the combination of electrical and mechanical CAD to connect all the electrical parts in the automotive at the optimum level.…

                 WEEK 9 - PROJECT 1 - DOOR TRIM LOWER WITH ENGINEERING FEATURES AIM:   Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements…

                           WEEK 9 - ATTACHMENT FEATURE CREATION - CHALLENGE 2 AIM: Create the Dog House for the Door Trim considering the design rules mentioned in the video.  "C" is where the doghouse contacts the backside of the surface  …

                                               WEEK 8 - CHALLENGE 4 - BUMPER AIM: Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A…

             ATTACHMENT FEATURE CREATION (RIBS & SCREW BOSS) - CHALLENGE 1 Aim:- To create an out featured rib on the centre console coin holder. Procedure:- Firstly open the coin holder using the open command Rib:- To create a rib first extract the base surface of the coin holder.…

                                          COIN HOLDER DESIGN AIM: Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should…

                             CHALLENGE 2 - SWITCH BEZEL DESIGN  Aim:       create the switch bezel plastic component through the given class - a surface Objective :      the objective of the project is to design…

                           Week 8 - Challenge 1 - Base Bracket Design Aim: To create a Base Bracket Plastic Component through a given Class A Surface and perform Draft Analysis on the final plastic component. Objectives:  Creation of Tooling…

                                            BACK-DOOR  DESIGN Objective: Use the provided styling surface to come up with a back door design, use appropriate design methodologies and provide the necessary…

                                                           ROOF CHALLENGE   OBJECTIVE: For the Given Roof styling, develop the essential flanges and reinforcements.…

                                                    SECTION MODULUS USING THE FORMULA OBJECTIVE: To increase the Section Modulus of the hood by necessary changes using NX cad. It is termed as the ratio of the second moment of area and distance from N.A (Neutral axis) to the extreme fiber. Also, it is the measure of the…

                                             DESIGN OF HOOD BY USING MASTER SKETCH  OBJECTIVE:Design Hood Outer Panel, Inner Panel and the necessary reinforcements by following the Master Section mentioned…

AIM: This project shows that examine the given fender wheel arch design to verify if the wheel arch of the fender meets the European standards. FENDER: Fender is the US English term for the part of an automobile (vehicle body) that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud,…

FENDER DESIGN OBJECTIVE : The main objective of this project is to design a fender using  a new age design software - NX - CAD INTRODUCTION : Design of any product starts from an requirement . The design engineer sketches the product based on the the requirement . Then the 2D sketch  with the proper dimensions…

                                  UNDERBODY COATING                      INTRODUCTION: A car’s underbody is exposed to the most wear and tear caused by muddy water, potholed…

AIM: DETAILED REPORT ON BENCHMARKING To prepare a report explaining what is Bench-marking , Compare at least 4 Vehicles and Provide a Preoper conclusion for the report ,suggesting a suitable vehicle among the comparison made. WHAT IS BENCHMARKING ? It is the process of comparing one's business process and performance…

TITLE:              RENDERING PROJECT OBJECTIVE: To Render All The Projects Done Previously . TOOLS USED  :Hardware Shaders. PROCEDURE: 1.Open Autodesk Alias. 2.Apply Visualisation To The Model. 3.From Control Panel Change The Setting From Modelling…

                                                     CONCEPT MODELLING OF SEATS OBJECTIVE:  To create the surface model of car seat using auto desk alias design.   INTRODUCTION: Concept…

                                             1.      TITLE OF THE PROJECT                                DEVELOPMENT…

TITLE :Concept modelling of steering wheel OBJECTIVE: To make a model of steering wheel from one image by visualization. INTRODUCTION: Concept modeling is modeling where 3d data starts to take shape. It is a crucial part of the process as every part involved in the design process depends on this to actually visualize,…

Challenge 6                                            CONCEPT  MODELING OF SIDE FENDER   Objective:-To create surfaces of the entire car fender using the isometric image of a car. Tools used:- Freedom…

                                   CONCEPT MODELLING OF CAR BUMPER ALIAS SOFTWARE OBJECTIVE: The main of the project is to create a concept model of the bumper of Abarth 500 car , using the curves and surface generation features with…

 CHALLENGE: 4                                                          CONCEPT MODELING OF AN ALLOY WHEEL OBJECTIVE: TO MAKE A MODEL OF AN ALLOY WHEEL USING ONE VIEW. INTRODUCTION:…