Week 9 - Project - A pillar Design with Master Section

DESIGN AND ASSEMBLY OF CV JOINT AND QUICK RETURN MECHANISM Objective:           The main aim of this report is to explain the procedure involved in design and assembly of CV joint and Quick return mechanism with the help of given 2D drawing sheets. Description: CV joint:            …

DESIGNING A PILLAR USING MASTER SECTION OBJECTIVES To improvise the Class A surface by resolving bad patches and adding flanges to it.  To create A pillar solid model with the help of  improvised class A surface. To create B side features for the A Pillar using the master section given to us as an input. To create…

A class-A surface from a vehicle door is provided to me to design a part model and validate it.           From this Door Applique as a Class - 'A' surface, first I need to check whether the surface has some boundary irregularities and any open boundaries. After checking I need to create a Tooling…

MESHING ON THE SUSPENSIONS ASSEMBLY AIM: Meshing on the give suspension assembly according to the given quality criteria and mesh parameters.Use Appropriate connections to connect the suspension assembly and perform Symmetry command to reflect the half finished model to the other side. PROCEDURE: STEP 1: Import…

Aim:  To perform geometry clean-up, mid-surface extraction, and mesh generation on the half part of the Instrument Panel of a four-wheeler vehicle adhering to the following quality criteria:   S.No  Quality Criteria  Value  1 Target/Average length   4 2 Minimum Length  2 3 Maximum…

AIM:     The main aim of the challenge is to morph the given model. OBJECTIVE:          Morphing means changing form or shape. Usually, in a design cycle, FE modeling and simulations are performed once the concept CAD is generated. With the need to reduce design iterations,…

Aim:  To  Create a DRILL HANDLE attach with B side features Ribs & screw boss plastic component design throught the given CAT Part file from Class A surface To make a Class B & Class C Surface and final component. Used via  Catia V5 software- tools used given…

Aim: To create core and cavity block for switch Bezel considering all plastic design rules. Steps Followed: Tooling Axis creation Checking Draft analysis for created tooling Axis Creating parting Surface Creating Core Side Creating cavity side. Tooling Axis: The tooling axis is the axis in which the core cavity opens…

  Aim:  To  Create a BUMPER DESIGN through the given CAT Part file from Class A surface To design a Class B & Class C Surface and final component. . Used via  Catia V5 software- tools used given below, Point through on the center of the surface Axis creation Line in point direction …

AIM:               Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. …

SWITCH BEZEL CHALLENGE:                     

AIM:      For the given Rear door FE model, Create and Apply different PIDs for different components. By using the same technique and the elements as shown in the video, Perform suitable connections.    PROCEDURE:    Firstly, import the given FE model into the Ansa software. …

AIM:      For the given Intake Manifold component, check for the geometrical errors and mesh the Surfaces with the given 2D element Quality criterias given below.    GIVEN PARAMETERS: S.No  Quality Criteria  Value  1 Target/Average length   3 2 Minimum Length  1 3…

AIM:          To check for the geometrical errors and mesh the Surfaces of the Rear view mirror with the given 2D element Quality criteria given below.    GIVEN PARAMETERS: S.No  Quality Criteria  Value  1 Target/Average length   1 2 Minimum Length …

AIM:       For both the models, Mid surface should be taken and meshed as per below quality criteria.   GIVEN QUALITY CRITERIA:     S.No  Quality Criteria  Value  1 Target/Average length   4 2 Minimum Length  2 3 Maximum Length  6 4 Aspect  3 5…

AIM:          For the given Plastic Bottle Cap model, check for the geometrical errors and take the mid surface by suitable mid surfacing techniques. PID and Thickness assignment has to be done for all the mid surfaces. Mesh the same with given element Quality criteria. (Refer the table Below for…

AIM:     For the given Hood model, Take the mid surface for all the components after checking the geometrical errors and mesh the mid surface with the given element Quality criteria. (Refer to the table below for the Quality criteria)    GIVEN:  S.No  Quality Criteria  Value …

AIM:      The task of this project is to quantify the improvement in fuel economy numbers for the hybrid vehicle (kmpl), compared to the conventional vehicle, on the urban cycle (UDDS) and highway cycle (HWFET). Also, to analyze and understand the vehicle operating points in terms of engine and motor speed,…

AIM:         To deal with the development of a forward energy-based fuel consumption model of a conventional vehicle. DESCRIPTION:            It is the Simulink model of the vehicle. It is modeled using a ‘Driver’ block, which is a basic PI controller…

AIM:           To simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB. For a 10 cell series lithium-ion battery model.   EXPLANATION:        In this project, the requirement that we…

AIM:        To prepare a detailed battery pack drawing along with its enclosure, and its assumptions. EXPLANATION:                                  lithium iron phosphate (LiFePO4) battery technology delivers…

AIM:          1) To Simulate the 3 test cases from the harness dashboard and write a detailed report on the results           2)coulomb counting Refer to the above model and explain how BMS implements coulomb counting for SOC   PROCEDURE:      …

AIM:       To Carry out a system-level simulation of an all-terrain vehicle and to Prepare a technical report explaining the model properties & comments on the results.   PROCEDURE:   OBJECTIVES TO KNOW:             1) BAJA ATV MODEL USING CVT.  …

AIM:                    To Implement the control logic of a “washing machine”.   PROCEDURE:                   Thus the working principles of the washing machine were given below;      …

 WE CAN FIND THE FOLLOWING DETAILS: AIM:             1) To make the Simulink model of Doorbell using Solenoid block.             2) To  Use a thermistor to sense the temperature of a heater & turn on or turn off the fan   OBJECTIVE 1:  …

AIM:  Create a Rankine Cycle Simulator using OCTAVE/MATLAB.   PROCEDURE   RANKINE CYCLE:                                 The Rankine cycle or Rankine Vapor Cycle is the process widely used by power plants such as coal-fired…

 AIM:  To write a function that extracts the 14 coefficients and calculates the enthalpy, entropy, and specific heats for all the species in the data file.               Here R is the universal gas constant, T is the temperature            …

AIM: write a code in MATLAB to optimize the stalagmite function and find the global maxima of the function. Clearly explain the concept of genetic algorithm in your own words and also explain the syntax for ga    PROCEDURE:   INTRODUCTION:               …

AIM:            To write a program that solves the following ODE THE GIVEN VALUES ARE:                                                          …

  AIM:  To write a program in MATLAB to simulate the forward kinematics of a 2R Robotic Arm.       PROCEDURE:   KINEMATICS: Kinematics is the science of describing the motion of objects using words, diagrams, numbers, graphs, and equations. Kinematics is the branch of mechanics.…

AIM      The below content shows  the materials and chemical  reactions occurring at the anode and  cathode of LCO, LMO, NCA, NMC, LFP, AND LTO  type of lithium-ion cells PROCEDURE     LITHIUM-ION BATTERIES: FIG(1) REPRESENTS THE  LITHIUM-ION BATTERY OR LI-ION…