Week 9-Challenge
WEEK 9 CHALLENGE
TO CREATE CONNECTORS AND ATTACH THE VARIOUS PARTS
MODEL 1. RIGHT RAIL_2 & FRONT TRUSS_1
(Seam Quad-angled+capped+L)
OBJECTIVE:
The main objective in week 9 challenge for model-1 is to create connectors between the two parts and than join them with given type of connectors in question page according to the element sizes.
Elements sizes:
Target- 5mm
PROCEDURE:
- File given can be directly opened by hypermesh as it is .hm file so open the file directly
- Press 'F' to fit the model in the screen
- Now bring all the seperate components into a seperate Assembly
- Than switch on the mesh which you want to work on than according to given connectors in challenge start connecting those
- Here for connecting Right Rail 2 & Front truss 1 by using Seam quad(angled+capped+L)
- Go to 2D - Connectors
- Location:nodelist
- Spacing:5mm
- Type: Seam-quad(angled+capped+L)
- Tolerance: 10mm
- Connect what - Comps: Select the components which needed to be connected than - Create
- If it is showing the nodes with red colour it is not realized properly than again we should check and if any values are missing should correct those and we should Realize those and bring that top green in colour.
- After connector is created properly we can see the new name in the components as - seam-quad (angled+capped+L)_comp
- Than the connector is created properly and check that and save the model
RESULT:
Finally the required type of connectors are created and connection are properly made . In this model 1 we have made Seam-quad(angled+capped+L) type of connector successfully.
MODEL 2. LEFT RAIL_2 & FRONT TRUSS_1
OBJECTIVE:
The main objective in week 9 challenge for model-2 is to create connectors between the two parts and than join them with given type of connectors in question page according to the element sizes.
Elements sizes:
Target- 5mm
PROCEDURE:
- File given can be directly opened by hypermesh as it is .hm file so open the file directly
- Press 'F' to fit the model in the screen
- Now bring all the seperate components into a seperate Assembly
- Than switch on the mesh which you want to work on than according to given connectors in challenge start connecting those
- Here for connecting Left Rail 2 & Front truss 1 by using Seam weld with Quad elements.
- Go to 2D - Connectors
- Location:nodelist
- Spacing:5mm
- Type: Quads
- Tolerance: 10mm
- Connect what - Comps: Select the components which needed to be connected than - Create
- If it is showing the nodes with red colour it is not realized properly than again we should check and if any values are missing should correct those and we should Realize those and bring that top green in colour.
- After connector is created properly we can see the new name in the components as - CQUAD4_comp
- Than the connector is created properly and check that and save the model.
RESULT:
Finally the required type of connectors are created and connection are properly made . In this model 2 we have made Seam weld with only quad elements successfully.
MODEL 3. RIGHT RAIL_1 , FRONT TRUSS_1 & FRONT TRUSS_2
OBJECTIVE:
The main objective in week 9 challenge for model-3 is to create connectors between the three parts and than join them with Spot weld with 3 layers & 5mm diameter
Elements sizes:
Target- 5mm
PROCEDURE:
- File given can be directly opened by hypermesh as it is .hm file so open the file directly
- Press 'F' to fit the model in the screen
- Now bring all the seperate components into a seperate Assembly
- Than switch on the mesh which you want to work on than according to given connectors in challenge start connecting those
- Here for connecting RIGHT RAIL_1 , FRONT TRUSS_1 & FRONT TRUSS_2 by using Spot weld with 3 layers & 5mm diameter.
- Go to 2D - Connectors
- Location: nodelist
- Select the nodes wherever joint has to be created using this nodelist and mention all other parameters properly
- Diameter :5mm
- Type: Weld
- num. layers: total 3
- Tolerance: 10mm
- Connect what - Comps: Select the components which needed to be connected than - Create
- If it is showing the nodes with red colour it is not realized properly than again we should check and if any values are missing should correct those and we should Realize those and bring that top green in colour.
- After connector is created properly we can see the new name in the components as - RBAR_comp
- Than the connector is created properly and check that and save the model.
RESULT:
Finally the required type of connectors are created and connection are properly made . In this model 3 we have made Spot weld with 3 layers and 5 mm diameter successfully.
MODEL 4. LEFT RAIL_1 , FRONT TRUSS_1 & FRONT TRUSS_2
OBJECTIVE:
The main objective in week 9 challenge for model-4 is to create connectors between the three parts and than join them with Seam weld with Hexa (adhesive) type.
Elements sizes:
Target- 5mm
PROCEDURE:
- File given can be directly opened by hypermesh as it is .hm file so open the file directly
- Press 'F' to fit the model in the screen
- Now bring all the seperate components into a seperate Assembly
- Than switch on the mesh which you want to work on than according to given connectors in challenge start connecting those
- Here for connecting LEFT RAIL_1 , FRONT TRUSS_1 & FRONT TRUSS_2 by using Seam weld with Hexa (adhesive) elements.
- Go to 2D - Connectors
- Location: nodelist
- Select the nodes wherever joint has to be created using this nodelist and mention all other parameters properly
- Type: Hexa (adhesive)
- Spacing : 5mm
- Strips & coats : 1
- Width : 1mm
- Tolerance: 10mm
- Connect what - Comps: Select the components which needed to be connected than - Create
- If it is showing the nodes with red colour it is not realized properly than again we should check and if any values are missing should correct those and we should Realize those and bring that top green in colour.
- After connector is created properly we can see the new name in the components as - Realize 4001 & solid_seam_hexa_adhesive_shell_gap
- Than the connector is created properly and check that and save the model.
RESULT:
Finally the required type of connectors are created and connection are properly made . In this model 4 we have made Seam weld with Hexa (adhesive) successfully.
MODEL 5. RIGHT RAIL_2 , REAR TRUSS_2
OBJECTIVE:
The main objective in week 9 challenge for model-5 is to create connectors between the two parts by creating holes and than join them with Bolt (general) .
Elements sizes:
Target- 5mm
PROCEDURE:
- File given can be directly opened by hypermesh as it is .hm file so open the file directly
- Press 'F' to fit the model in the screen
- Now bring all the seperate components into a seperate Assembly
- Than switch on the mesh which you want to work on than according to given connectors in challenge start connecting those
- Here for connecting Right Rail 2 & Rear truss 2 by using Bolt (general) joint.
- Go to 2D - Connectors
- Location: nodelist
- Select the nodes wherever joint has to be created using this nodelist and mention all other parameters properly
- Location:nodelist
- num. Layers: total 2
- Create hole if none - Adjust hole position (2D)
- Type: Bolt (General)
- Tolerance: 10mm
- Strips & coats : 1
- Width : 1mm
- Tolerance: 10mm
- Connect what - Comps: Select the components which needed to be connected than - Create
- If it is showing the nodes with red colour it is not realized properly than again we should check and if any values are missing should correct those and we should Realize those and bring that top green in colour.
- After connector is created properly we can see the new name in the components as - bolt(general)_rigid_comp & bolt(general)_comp
- Than the connector is created properly and check that and save the model.
RESULT:
Finally the required type of connectors are created and connection are properly made . In this model 5 we have made Bolt (general) joint successfully.
MODEL 6. LEFT RAIL_2 & REAR TRUSS_2
OBJECTIVE:
The main objective in week 9 challenge for model-6 is to create connectors between the two parts by creating holes and than join them with Bolt (general) .
Elements sizes:
Target- 5mm
PROCEDURE:
- File given can be directly opened by hypermesh as it is .hm file so open the file directly
- Press 'F' to fit the model in the screen
- Now bring all the seperate components into a seperate Assembly
- Than switch on the mesh which you want to work on than according to given connectors in challenge start connecting those
- Here for connecting LEFT RAIL_2 & REAR TRUSS_2 by using Bolt (general) joint.
- Go to 2D - Connectors
- Location: nodelist
- Select the nodes wherever joint has to be created using this nodelist and mention all other parameters properly
- Location:nodelist
- num. Layers: total 2
- Create hole if none - Adjust hole position (2D)
- Type: Bolt (General)
- Tolerance: 10mm
- Strips & coats : 1
- Width : 1mm
- Tolerance: 10mm
- Connect what - Comps: Select the components which needed to be connected than - Create
- If it is showing the nodes with red colour it is not realized properly than again we should check and if any values are missing should correct those and we should Realize those and bring that top green in colour.
- After connector is created properly we can see the new name in the components as - bolt(general)_rigid_comp & bolt(general)_comp
- Than the connector is created properly and check that and save the model.
RESULT:
Finally the required type of connectors are created and connection are properly made . In this model 6 we have made Bolt (general) joint successfully.
MODEL 7. RIGHT RAIL_1 & RIGHT RAIL_2
OBJECTIVE:
The main objective in week 9 challenge for model-7 is to create connectors between the two parts and than join them with Spot weld with Rigid elements.
Elements sizes:
Target- 5mm
PROCEDURE:
- File given can be directly opened by hypermesh as it is .hm file so open the file directly
- Press 'F' to fit the model in the screen
- Now bring all the seperate components into a seperate Assembly
- Than switch on the mesh which you want to work on than according to given connectors in challenge start connecting those
- Here for connecting RIGHT RAIL_1 & RIGHT RAIL_2 by using Spot weld with Rigid elements.
- Go to 2D - Connectors
- Location: nodelist
- Select the nodes wherever joint has to be created using this nodelist and mention all other parameters properly
- Diameter :5mm
- Type: Rigid
- num. layers: total 2
- Tolerance: 10mm
- Connect what - Comps: Select the components which needed to be connected than - Create
- If it is showing the nodes with red colour it is not realized properly than again we should check and if any values are missing should correct those and we should Realize those and bring that top green in colour.
- After connector is created properly we can see the new name in the components as - RBE2_comp
- Than the connector is created properly and check that and save the model.
RESULT:
Finally the required type of connectors are created and connection are properly made . In this model 7 we have made Spot weld with Rigid elements of 2 layers and 5 mm diameter successfully.
MODEL 8. LEFT RAIL_1 & LEFT RAIL_2
OBJECTIVE:
The main objective in week 9 challenge for model-8 is to create connectors between the two parts and than join them with Spot weld with 2 layers & 5mm diameter with spring elements
Elements sizes:
Target- 5mm
PROCEDURE:
- File given can be directly opened by hypermesh as it is .hm file so open the file directly
- Press 'F' to fit the model in the screen
- Now bring all the seperate components into a seperate Assembly
- Than switch on the mesh which you want to work on than according to given connectors in challenge start connecting those
- Here for connecting LEFT RAIL_1 & LEFT RAIL_2 by using Spot weld with 2 Layers .
- Go to 2D - Connectors
- Location: nodelist
- Select the nodes wherever joint has to be created using this nodelist and mention all other parameters properly
- Diameter :5mm
- Type: Spring
- num. layers: total 2
- Tolerance: 10mm
- Connect what - Comps: Select the components which needed to be connected than - Create
- If it is showing the nodes with red colour it is not realized properly than again we should check and if any values are missing should correct those and we should Realize those and bring that top green in colour.
- After connector is created properly we can see the new name in the components as - CELAS 1_comp
- Than the connector is created properly and check that and save the model.
RESULT:
Finally the required type of connectors are created and connection are properly made . In this model 8 we have made Spot weld with 2 layers and 5 mm diameter SPRING ELEMENTS successfully.
MODEL 9. FRONT TRUSS_1 & FRONT TRUSS_2
OBJECTIVE:
The main objective in week 9 challenge for model-9 is to create connectors between the two parts and than join them with Spot weld with 2 layers & 5mm diameter
Elements sizes:
Target- 5mm
PROCEDURE:
- File given can be directly opened by hypermesh as it is .hm file so open the file directly
- Press 'F' to fit the model in the screen
- Now bring all the seperate components into a seperate Assembly
- Than switch on the mesh which you want to work on than according to given connectors in challenge start connecting those
- Here for connecting FRONT TRUSS_1 & FRONT TRUSS_2 by using Spot weld with 2 Layers & 5mm diameter.
- Go to 2D - Connectors
- Location: nodelist
- Select the nodes wherever joint has to be created using this nodelist and mention all other parameters properly
- Diameter :5mm
- Type: Weld
- Spacing: 5mm
- num. layers: total 2
- Tolerance: 5mm
- Connect what - Comps: Select the components which needed to be connected than - Create
- If it is showing the nodes with red colour it is not realized properly than again we should check and if any values are missing should correct those and we should Realize those and bring that top green in colour.
- After connector is created properly we can see the new name in the components as - RBAR_comp
- Than the connector is created properly and check that and save the model.
RESULT:
Finally the required type of connectors are created and connection are properly made . In this model 9 we have made Spot weld with 2 layers and 5 mm diameter successfully.
MODEL 10. FRONT TRUSS_1, FRONT TRUSS_2 & Reinf_Plate
OBJECTIVE:
The main objective in week 9 challenge for model-10 is to create connectors between the three parts and than join them with Seam weld.
Elements sizes:
Target- 5mm
PROCEDURE:
- File given can be directly opened by hypermesh as it is .hm file so open the file directly
- Press 'F' to fit the model in the screen
- Now bring all the seperate components into a seperate Assembly
- Than switch on the mesh which you want to work on than according to given connectors in challenge start connecting those
- Here for connecting FRONT TRUSS_1, FRONT TRUSS_2 & Reinf_Plate by using Seam weld .
- Go to 2D - Connectors
- Location: nodelist
- Select the nodes wherever joint has to be created using this nodelist and mention all other parameters properly
- Type: Weld
- Spacing: 5mm
- Tolerance: 10mm
- Connect what - Comps: Select the components which needed to be connected than - Create
- If it is showing the nodes with red colour it is not realized properly than again we should check and if any values are missing should correct those and we should Realize those and bring that top green in colour.
- Always selection of node lists should be made independently one side after the other side than only the joint will be proper.
- After connector is created properly we can see the new name in the components as - RBAR_comp
- Than the connector is created properly and check that and save the model.
RESULT:
Finally the required type of connectors are created and connection are properly made . In this model 10 we have made Seam weld successfully.
MODEL 11. REAR TRUSS_1, REAR TRUSS_2
OBJECTIVE:
The main objective in week 9 challenge for model-11 is to create connectors between the two parts and than join them with Seam weld.
Elements sizes:
Target- 5mm
PROCEDURE:
- File given can be directly opened by hypermesh as it is .hm file so open the file directly
- Press 'F' to fit the model in the screen
- Now bring all the seperate components into a seperate Assembly
- Than switch on the mesh which you want to work on than according to given connectors in challenge start connecting those
- Here for connecting Rear Truss 1 & Rear truss 2 by using Seam weld .
- Go to 2D - Connectors
- Location: nodelist
- Select the nodes wherever joint has to be created using this nodelist and mention all other parameters properly
- Type: Weld
- Spacing: 5mm
- Tolerance: 10mm
- Connect what - Comps: Select the components which needed to be connected than - Create
- If it is showing the nodes with red colour it is not realized properly than again we should check and if any values are missing should correct those and we should Realize those and bring that top green in colour.
- Always selection of node lists should be made independently one side after the other side than only the joint will be proper.
- After connector is created properly we can see the new name in the components as - RBAR_comp
- Than the connector is created properly and check that and save the model.
RESULT:
Finally the required type of connectors are created and connection are properly made . In this model 11 we have made Seam weld successfully.
NOTE: All the screenshots of before connectors and after connectors are attested in the word file please check that