Conjugate Heat Transfer Analysis on Exhaust port using ANSYS Fluent
…
Rohit Deshmukh
updated on 29 Apr 2021
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Be the first to add a comment
Read more Projects by Rohit Deshmukh (48)
Using Stateflow to work a Washing Machine and Gearbox using Simulink
Week4 Challenge AIM: 1.To Implement a control logic of a “washing machine” using Stateflow as per the given sequence: If the power supply is available, the system gets activated If the Water supply is not available, stop the process & indicate through LED Soaking time should…
15 Jul 2021 05:40 PM IST
Creating a Doorbell model and a Temperature Sensor for Fan using Simulink
Week 2 Report. Make a Simulink model of Doorbell using a solenoid block with the following details: In the above arrangement, when the switch is closed the electromagnet receives electrical power from the battery and pulls the metal arm to hit the bell producing sound. Create a situation where…
21 Jun 2021 09:59 AM IST
Parametric study on Gate valve using ANSYS Fluent
Week9 Report: Aim: For this challenge, you will have to perform a parametric study on the gate valve simulation by setting the opening from 10 % to 80%. Obtain the mass flow rates at the outlet for each design point. Calculate the flow coefficient and flow factor for each opening and plot the graph. Discuss…
25 May 2021 07:25 AM IST
Simulating Combustion of Natural Gas using ANSYS Fluent
Week 10 Report Aim: 1. Perform the simulation analysis using methane-air fuel mixture and plot the variation of mass fraction of different species using line probes at different locations of the combustion chamber. 2. To study the effect of adding water to the methane-air mixture and plot the same and discuss…
25 May 2021 07:24 AM IST
Simulating Cyclone separator with Discrete Phase Modelling using ANSYS Fluent
Week8 Report Aim: To perform an analysis on a given cyclone separator model by varying the particle diameter, particle velocity and calculate the separation efficiency. Theoretical Introduction: A cyclone separator is an economical device for removing particulate solids from…
20 May 2021 04:56 PM IST
Simulation of a Flow over a Cylinder using ANSYS Fluent
…
17 Apr 2021 11:44 AM IST
Stability Analysis in Linear System
Week 6 Report. Aim: To understand the Stability Analysis in Linear Systems and calculate the Spectral Radius for the different Iterative Methods. Theoretical Introduction:In mathematics, stability theory addresses the stability of solutions of differential…
24 Mar 2021 07:16 AM IST
Simulation of a 1D Super-sonic Nozzle flow by MacCormack Method using MATLAB
…
12 Mar 2021 12:16 PM IST
Solving the steady and unsteady 2D heat conduction problem using MATLAB.
…
19 Feb 2021 12:27 PM IST
Parsing and calculating NASA Thermodynamic data using MATLAB.
Project1 Report. Aim: To write a code that reads the given file and then extracts the necessary data for the calculation and Plotting of the various thermodynamic Properties accordingly. Introduction: Parsing, syntax analysis, or syntactic analysis is the process of analyzing a string of symbols,…
10 Feb 2021 06:24 PM IST
Creating a Rankine cycle Simulator using MATLAB.
Project2 Report. Aim: To write a code that calculates the properties at all the state points and then plots the Temperature-Entropy and the Enthalpy-Entropy Diagram for the given Rankine Cycle. Introduction:The Rankine cycle is a model used to predict the performance of steam turbine systems.…
29 Jan 2021 05:18 AM IST
Write a code to fit a curve of the original Data set using MATLAB
Week3 Report. Aim: To write a code to fit a curve of the given data set and to use the splitwise method for the same. Introduction: Curve fitting is the process of constructing a curve, or mathematical function, that has the best fit to a series of data points, possibly…
20 Jan 2021 05:09 AM IST
Solid Meshing on Different components in Hypermesh
…
14 Jan 2021 05:16 AM IST
Plotting of a simulation to study the workspace of a 2R Robotic Arm using MATLAB
Week 2 Report. Aim: To plot a proper simulation of the two links and get the position of the manipulator of the Robotic Arm. Introduction: Kinematics in robotics is a statement form about geometrical description of a robot structure. In other word, kinematics is the relationship between…
12 Jan 2021 05:40 AM IST
Crash Analysis for a given Specimen before and after Element Property Change in RADIOSS
…
01 Dec 2020 09:38 AM IST
Shell Meshing on a Wheel Floor Panel using Hypermesh.
…
23 Nov 2020 09:02 AM IST
Meshing and Connections on a Suspension Assembly using ANSA.
Report on Meshing of a Rear…
18 Nov 2020 04:48 AM IST
Shell Meshing for a Bottle Cap Model using ANSA.
…
18 Nov 2020 04:47 AM IST
Solid Meshing for a Rear View Mirror Model using ANSA.
…
18 Nov 2020 04:47 AM IST
Connections on a Rear Door Model using ANSA.
…
18 Nov 2020 04:47 AM IST
Shell Meshing on a Side Door Trim using Hypermesh
…
18 Nov 2020 04:43 AM IST
Different types of Connections on a truss model in Hypermesh
…
30 Oct 2020 03:17 PM IST
Shell Meshing for a Car Hood Model using ANSA
…
19 Oct 2020 04:33 AM IST
Shell Meshing on an Automobile Hood using Hypermesh.
…
19 Oct 2020 04:32 AM IST
Mid-surfacing, Meshing with 1D Connections on a Mechanical Bracket using Hypermesh
…
17 Oct 2020 08:42 AM IST
Creation of Switch Bezel using Surface Design in Catia V5
Week 8 Part 9 Project 9 1. Class A Surface. 2. Class B Surface. 3. Class C Surface. 4. Final Trim. 5. Solid Surface. 6. Draft Analysis. 7. Tooling Axis…
16 Sep 2020 06:35 PM IST
Shell Meshing on an Instrument Panel of a Vehicle
…
06 Sep 2020 08:15 AM IST
Creation of sketches in the Drafting Workbench using Catia V5
PDF file attached as well. Creation of Base Mount Bracket
05 Sep 2020 08:51 AM IST
Creation of a Base Mount Bracket using Catia V5
Presentation also attached. …
04 Sep 2020 08:09 PM IST
Morphing Techniques on a Component
…
21 Jul 2020 11:09 AM IST