Week 3 Challenge

                                                          REPORT  1) Main Tooling Direction  The Tooling Direction is basically the direction that the mold pulls apart.…

TREE_STRUCTUREMAIN_PRODUCT_MASTER_FILESU7B_FILES_CLASS_A  PRODUCT_FILE UPLOADED FILE CONTAINS TOOLING_DIR,B_SIDE,CLOSE_BODY,FOCAL FUNCTIONS- AS THIS MUST BE WORKED  IN THE FURTHER CHALLANGES  THERE WAS DATA MANAGEMENT ISSUE FROM MY SIDE PLEASE VALIDATE FOR THEE SAME,,THANK YOU IN ADVANCE,,  

1 – What is the full form of OEM ?     ans:- The full form of OEM is (Original Equipment Manufacturer) 2 – How the Design Responsibility  goes in Automotive ? ans:- OEM (Original Equipment Manufacturer)          Tier 1 Suppliers        …

OBJECTIVE The objective of this project is to design a butterfly valve and apply GD&T to it's components and final assembly using Siemens NX. INTRODUCTION  A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter…

                                     DESIGN OF AUTOMOTIVE MECHANICAL WIRING HARNESS FOR ENGINE     Aim- To route the wiring harness on given Engine and flatten view drawing in CATIA V5. Objective- The objective of the project is to route the wiring harness on given Engine and prepare flatten view drawing in CATIA V5. All…

AUTOMOTIVE WIRING HARNESS BACKDOOR Statement of assignment : Route the Wiring harness on Given car body and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. Available connector…

                                                                         REPORT_WIRING_HARNESS_FLATENNING   Aim: To Flatten previously…

                                                                           Wiring harness Routing Aim: Route two electrical harnesses…

                                                                      REPORT ON HARNESS ROUTING LAYOUT   Objective: To Route the harness layout…

                                                                                REPORT ROUTING & PCKING RULE     The given clip was downloaded and opened as a part file. I have to define two points that will be used as entry and exit points. Then a plane has to be defined at the points. A base plane has to be defined at…

                                                      WIRING HARNESS DESIGN IN CATIA V5INTRODUCTION:A wire harness is a system of insulated conducting wires bound together with…

                      REPORT                                                                  DESIGN…

                                                                    ASSEMBLY WORK BENCH     Mechanical assembly is the process of…

                                                                                           …

                                                                                           …

                                                                                                 REPORT  AIM  : Create the Dog House for the Door Trim considering the design rules mentioned in the video. Consider the thickness of the part to be 2.5 mm   OBJECTIVES :       "C" is where the doghouse contacts the backside…

AIM :- Create the rib and screw bosses for the Drill Handle considering the design rules mentioned. OBJECTIVES :- FOR RIBS  DESIGNING THE RIB & SCREW BOSSESS WITH THE CLASS_A SURCE PROVIDED. Create  CLASS_B , CLASS_C AND CLOSED BODY WITH THE DRAFT ANALYSIS.   .    FOR SCREW BOSSES :- General Guidelines for Bosses:   Draft …

              REPORT ON CORE AND CAVITY EXTRACTION    AIM                    Create the Core and cavity blocks for the switch bezel designed in the earlier challenge. OBJECTIVES :                   Using previously created part using class_A surface                      DRAFT ANALYSIS FOR COMPLEATED PART :- CORE  :-  …

                            DESIGN,CREATION OF CLASS_B & C SURFACE ADN DRAFT ANALYSIS OF DOOR TRIM LOWER   AIM  :- Create the Door Trim Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A…

                                                           DESIGN AND DRAFT ANALYSIS OF BUMPER AIM Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the…

                                                                   Coin Holder Design INPUT CLASS A :- QUALITY OF THE CLASS A (BY SEEING THE CONTINUITY ) TO FIND THE SPECIFIED TOOLING AXIS FOR THE PRODUCT TO BE MANUFACTURED ( IN ALL X,Y,Z DIRECTIONS ),                 USING THE DUMMY TOOLING AXIS   DUMMY TOOLING AXIS TOOLING…

                                                                           REPORT (SWITCH BEZEL)         …

                                                                        BASE_BRACKET_CREATION     INPUT :-   CLASS…

First of all Buying a Car is a big Decision & can be the Desires  there are many Models of different OEMs available in the market.and its not easy to select a single car from these overwhelming world ,But if we follow a step-by-step process, the task can become a bit easy. to suggest a better car under the…

AIM OF THE PROJECT : To design the back door of the carr and  make the inner panel for the back door and also design the necessary re-enforcements. SOFTWARE : NX 12.0 Car Back Door and Components :                The back door is a hinged door/tailgate at the rear of the vehicle. It may be used for loading and unloading…

AIM To create and assemble the hood inner panel and outer panel and their reinforcements by following the design rules and master section. Objective Design hood outer panel, inner panel and reinforcements with the given outer hood skin, master section and design parameters. Introduction The hood or bonnet is the hinged…

                                               DESIGNING THE ROOF USING NX-CAD   OBJECTIVE To Design the required reinforcment and flanges for the given Class A surface of Roof.Required reinforcments…

SECTION MODULUS CALUCULATION AND OPTIMIZATION : Aim's of the challange - To calculate the section modulus of the previously designed hood for analyzing its strength and also optimizing the design to see the difference in the bending strength of the hood. Higher the section modulus of a structure, the more the resistive…

Objective To design a front fender from the given skin data and the master section provided with Drip mounting, A-pillar, Sill, Bumper and Baffle (splash) Mounts. To Prepare a report by explaining about Fender Design and its different mounts , manufacturing process and its design parameters.   What is a Fender ? Fender is…