Week 1:- Introduction to BiW and Fixtures Challenge

1. What is BIW & define its parts?

• Body in white (BIW) refers to the stage in the automobile manufacturing in which a car body’s components have been joined together, using one or a combination of different techniques: welding (spot, MIG/MAG), riveting, clinching, bonding, laser brazing etc.
• Body in White, or BIW, is a stage in the production of automobiles in which all sheet metal components such as the roof, body side, under body, backdoor, cross members, and other components are welded together and the resulting body is dipped in a primer solution, which has a greyish colour and thus gives the body its name. The car's shape is determined by the BIW, which is obtained after welding and before painting.

        BIW is mainly categorized as:

• Body side
• Under body
• Closures
• Roof
• Fender
• Reinforcements

2.What do you understand by BIW nomenclature?

• A nomenclature in BIW is basically naming every part of the body. These names can be said as subparts of the already categorized parts above.
• The nomenclature differs a little bit from region to region but the overall idea is to name individual automotive sheet metal components.
• Below images show the nomenclature of BIW: 

3.What is fixture & its types?

• Fixture is a holding device which holds the workpiece to be processed.
•  In general fixtures are designed using 3-2-1 principle. Further, fixture should firmly hold the work piece without causing vibrations, distortions, stresses in the workpiece and also fixture should not disturb or interfere the processing of the workpiece.

Types of fixture

• Production fixture
• Production fixture
• Checking fixture

4 What is the basic priciple of fixture design ?

• The fixture is designed based on how the workpiece is fixed on the fixture. All the Degrees of Freedom of the workpiece are to be constraint.
• The 3-2-1 principle is used.

• The part is now fully constraint and cannot move

• The 3 points are used as 3 points to define a plane. Four points cannot be used due to irregularity of the surface in real world.

5.Elaborate types of BIW Stations? 

• The BIW assembly line is where different types of panels are joined together in each specified zone like Underbody zone, Hood zone Etc.
• These zones are further subdivided into stations, where various processes like welding gluing and inspection are done to the part of that particular zone before they are being assembled together. For instance, in the roof zone, various reinforcement is to be added before they are married to the side zone.

The BIW assembly line can be classified as follows:

1. Tools
2. Grippers
3. Stands
4. Miscellaneous

• A tool is a fixture which consists of number of different units together to hold a car panel or assembly. 

Geo Tool:

• A geo tool is a fixture in which the geometry of the panel which is welded together is defined accurately.
• In geo fixture two panels will be loaded and welded together.
• Pin tolerance for geo fixture is about -0.15mm.

Re-spot Tool:

• A re-spot tool is a fixture where already welded panels are brought to be welded further.
• For example, on a certain panel we needed to have 50 weld but due to assembly line constrains we managed to achieve 30 on geo tool, then the remaining 20 will be achieved on the re-spot tool.
• Pin tolerance for the re-spot tool is -0.28mm.

Marriage or hemming tool:

• Marriage or hemming tool is a fixture in which the inner panel and outer panel is joined together.
• Hemming is not done for every part but only for those parts where we want to join two panels without other joining process as it may affect the aesthetics of the car.
• Hemming can be found on Hood, Back door etc.

Checking stations:

It is used to check the automotive part or assembly to ensure all the coordinated, relative dimensions and positions are as per tolerance. It can be classified as follows:

• Gauge type checking fixture is where the work piece is held and various gauges are introduced to ensure the dimensions and repeatability.
• Fixed type checking fixture is where the work piece is fixed using clamps and pins and the Coordinate Measuring Machine is used to measure the coordinates of different points of the panel and compare it with the nominal value and give its report to rectify any errors.
• Automated checking fixture is where the automated setting are being done through sensors, PLCs, switches etc, to give a signal in case of any irregularities which can be rectified. As it is expensive, it is not widely used.

 Grippers Stations

• A gripper is a device that enables the holding of an object to be manipulated.
• The easier way to describe a gripper is to think of the human hand. Just like a hand, a gripper enables the holding, tightening, handling, and releasing of an object. A gripper is just one component of an automated system.
• A gripper can be attached to a robot or it can be part of a fixed automation system.

Different stands are used in BIW

1.  Pedestal stands

• Weld gun is mounted on the fixed stand which is mounted to the floor The gripper can carry the panel under the stand to do the operation.

    2.Gluing & sealer stand

• Gluing gun or sealer gun is fixed to a welded or a standard stand which is grouted to the floor

   3.Docking stand

• The robots have some limitations such as the payload capacity of the robot & also due to lack of
• When we select the robot for multitasking it can't do both the task simultaneously due to
• In this kind of case, we add a docking stand to put some equipment that is not in use for the current operation but will be required for next
• Hence the robot can drop a gripper or gun & pick the next operation equipment to complete the task from the docking

6. What are the basic terminologies used in the BIW fixture? 

Basic terminologies used in the BIW fixture

• The following terminologies are used in BIW

        A) NC/Mylars/Fingers

• Mylars are the component that holds the panel while These are placed from topside & from the bottom side also. The top side Mylars called Clamping Mylars & the bottom side Mylars called Resting Mylars. Every clamping Mylars have resting Mylars. It doesn't allow deformation of the part due to welding stresses.
•  

      B) Principle locating point (PLP)

• These are the points that are used for the accurate location of the part to maintain the geometry of the part. There is lots of holes on the panel which are not accurate due to stamping operation. The PLP are defined in the drawing. The positional dimensions or relative dimensions are very precise in stamping & in fixtures also.

       C) Risers

• Risers are of different types like L-typer rises, Square tube riser Riser is the manufacturing part which gives height to the assemblies.

       D) Blade

• Blades are plates mounted on the Other parts like cylinder, arms, etc are mounted on the blade.

      E) Shims

• Shims are the small part that comes with the thickness of 0.1mm, 0.2mm, 0.5mm, etc. These will compensate for the stackup tolerance which reflects at the panel holding part called We give tolerance to all the parts of the fixture. Due to this tolerance, the Mylars will either lift up or goes down from their defined position.
• If the Mylars go down from the defined height it will make an impression or dent on the panel.
• If the Mylars lift up then there will be a distorsion due to welding stress. To adjust the Mylars At its defined position we use shims so the panel won't be deformed & also don't get any impression on it.

      F) Rough locators

• The operator can place the part in the wrong orientation The rough locator will work as a guide while placing the part in the fixture & the part will be loaded in the desired orientation. It is a part of foolproofing.

     G) Hardware

• Hardware is like the Hex head bolts, Allen Bolts, Hex nuts, Spring washers, Self-locking nuts

     H) CMM

• CMM stands for coordinate measuring machine. It is a device that measures the geometry of physical objects by sensing discrete points on the surface of the object with a probe. It generates a report by comparing the data with the CAD file data.

       I) Unit

• The fixture is the assembly of different types of units to form a part. There are different units like pin unit, base unit, clamping unit, etc.

       J) Number plates

• The number plate is the aluminum embossed plate placed on each unit for easily recognizing the part unit.

       K) Nameplate

• The data like manufacturing company name, fixture type, Fixture weight is embossed on the plate & joined to the fixture.

        L) Clamp Arm

• The clamp arm is the part of the clamp unit which moves an Over clamp arm the Mylars are mounted.

       M) Pivot

• It is an axis about which the clamp arm will rotate

       N) Class A Surface/Skin surface

• The outer panels of the car like a hood, door, backdoor, fender, roof are visible to the customer.
• The outer panels should be aesthetically very good. No scratches or dent is acceptable over it.
• While designing the fixture to the skin surface the clamping material should be soft, so that it could not able to left any impression or dent over the skin. generally, nylon or PU material is used for clamping purposes.

       O)Reed switches & sensors

• These are the electric components used in automated The reed switch is an electrical switch operated by an applied magnetic field. The detects the panel is loaded or not is done by sensors.