Project 2_Design & Analysis of a Hostel building at Guwahati, Assam

                                                  PROJECT 02 DESIGN AND ANALYSIS OF A HOSTEL BUILDING AT GUWAHATI, ASSAM   Aim: To carryout modelling, analysis, design, and preparation…

                                        CHALLENGE 12 1. AIM: To Analyze and designthe isolated footing from week 11 challenge on SAFE To verify the size, depth and steel provided as per calculations.   INTRODUCTION:…

                                        CHALLENGE 11            DESIGN OF SHALLOW FOUNDATION ISOLATED FOOTING   Aim: To design a square footing for a column of size 400x400 using some…

                                     CHALLENGE 09 Aim: To model and analyze the G+7 storey building using ETABS with application of proper load cases and load combinations for the given typical floor plan drawing. PROCEDURE:…

                                  CHALLENGE 09 ANALYSIS AND DESIGN OF RCC SHEAR WALLS IN THE MODEL USING ETABS   Aim: To run the anlaysis and design the RCC Shear walls for the given ETABS model. To extract the values of longitudinal…

                                                CHALLENGE 08     Aim:- To provide, The details of longitudinal reinforcement for the two columns (3A & 3B), from foundation to terrace…

                                           CHALLENGE 07   Aim:    To Providing details of longitudinal and shear reinforcement for the two continuous beams using ETABS. Step 1: 1) After downloading…

                                                PROJECT 01   AIM: TO MODEL AND ANALYZE MULTIPLE BUILDINGS WITH DIFFERENT FLOOR LEVELS AND DESIGN PARAMETERS USING ETABS SOFTWARE AND COMPARE THE RESULTS…

                                          CHALLENGE 06   AIM:  ETABS modelling of a 25 storey building. Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth…

                                               CHALLENGE 05   1.  Restraint to floor Shrinkage: Structure A is full restraints at all corners. It will have higher restraint to shrinkage, thus…

                                        CHALLENGE 04   Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams).…

                                       CHALLENGE 03    

                                    CHALLENGE 02   1. Static Analysis:              It is in linear state and does not vary with time. It does not depend on time.  Static force does not…

                                         CHALLENGE 01   1. a)       Observation: Concrete crushed and reinforcement is exposed. Concrete spalled beyoned the reinforcement which may be a sign of rupture.…

                                             PROJECT 02 CREATING A 3D RENDERED MODEL FOR A RESIDENTIAL BUILDING IN AUTOCAD: AIM:     To draw the 3D Residential Building and To create the Rendered…

                         CHALLENGE 12 Creating 3D Isometric view of various structural elements in AutoCAD   1)  Create a 3D Isometric View of the building with plan and elevation given: Aim:  To draw the 3D Isometric View of the building…

                                      CHALLENGE 11 Creating various 3D Models like Furniture, Footing, Girder, Column drop with panel and Gable Wall in AutoCad:   1) CREATING 3D FURNITURE ELEMENT: Aim :-      To…

                                   CHALLENGE 10 Creation of Multiple viewports, Scaling the drawing and setting in Template in AutoCad AIM: To create layout of plan and section, creating viewports, editing attributes and taking a…

                              CHALLENGE 09 Creating Kitchen layout, Hatching of Architectural elements and sectional view of an Industrial Building in AutoCad   1) CREATING KITCHEN LAYOUT:  Aim:     To create the layout…

                             CHALLENGE 09 Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCad 1. CREATE TITLE BLOCKS: Aim:        To create the titleblock named Custom1_titleblock…

                         CHALLENGE 08 - PROJECT01 CREATING AN ARCHITECTURAL PLAN FOR THE PROVIDED PLOT SIZE AND DEVELOP RELEVANT BASIC STRUCTURAL DRAWINGS:   AIM:       To draw:  1. Architectural Drawing of a Residential Building:…

                                                               CHALLENGE 05 AIM:   To create the column schedule using the necessary commands in…

                                 CHALLENGE 04 Creating a Residence Layout, Seating plan, Toilet and Utility room plan using AutoCad   AIM:    To draw the layout of a Residence plan. Commands Used: Line Offset Trim Extend…

                                       CHALLENGE 03 DRAWING 01: AIM:    To Draft the various given geometries using Chamfer, Fillet tool in Autocad. Commands Used: Line circle trim Procedure: Open new file and…

                                              CHALLENGE 02 CREATING A FLOOR PLAN, FOOTING DETAIL AND ISOMETRIC VIEW USING AUTOCAD 1) C/S OF LOAD BEARING WALL WITH SPREAD FOOTING:  Aim:    …

                                   CHALLENGE 01  P01    AIM:     To create the geometric coordinates from given drawings by using the coorindate system methods. In the P1 and P2 drawings by using all…

  Structural drawings required to be provided to the site for construction: Centre line drawing Footing and column layout with reinforcement details. Column schedule with reinforcement details Plinth beam layout with reinforcement details First floor beam layout with reinforcement details First floor slab layout with…

                                      CHALLENGE 05  1) Calculation of Concrete Mix Design for M35 Grade Concrete with Flyash:   i) Stipulations for Proportioning: Grade of concrete : M35 Type of cement : OPC 43…