Project 2_Design & Analysis of a Hostel building at Guwahati, Assam

Aim: To analys the given hostel building using etabs and safe software procedure: STEP1: USING ETABS 1) open File and select new model and select the metric system and code details and Click Ok 2)open and Edit the grid data as provided in the plan.and story data 3)Go to Define tab and  Define the…

aim: Design a square footing for a column size of 400x400. The compression axial load for the load combination of (1.5 DL + 1.5 LL) is 2000 KN. The safe soil bearing capacity is 150 KN/m2 at a depth of 2 metres below E.G.L. Participants are free to go for either a tapered or stepped footing. Besides the total axial load,…

1)AIM: The architectural drawings for a G-7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout and then model the building in Etabs. The following architectural drawings have been provided:…

The etabs file for a G+6 building is provided. Run the analysis and design the RCC shear walls (show in the etabs model). The following challenge deals specifically with the shear wall of size 300x1500 at grid A-11 in the structural model Extract values of longitudinal steel ratio, boundary element length and shear reinforcing…

ans aim: To Model and analyze a 10 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the foundation level. Each of the successive 10 storeys has a storey height of 4 metres. Assume the Structural element sizes (Beam, Column,…

ans: AIM: From ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment Resisting Frame. The following challenge deals specifically with two columns at the following grid intersections 1.3a 2.3b Procedure: 1)Now Open privoius G+4 Etab file 2) Click the Concrete Frame Design tool top righty…

AIM: Detail design of beams in Etabs 2019.The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.         1) 3 span continuous beam along grid A     …

1)Effect of stiffness on T Aim: To compare the effect of stiffness on natural period of buildings E & F and G & H  Building E: 1) Open New model and set number of stories as 10 and number of bays in X direction as 4 and in Y direction as 3 2) Define the section property of column as 400X400mm for upper 5 storeys,Bottom…

Ans: 1) AIM: Model a 25 storey building on ETABS 2018 with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. procedure: 1) Open ETABS software and Click on the File menu and…

Question 1:The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account…

Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. ans: A)we can see symmetry structure and columns and beams are…

Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. 1ans) now for mode1 now for mode2 now for mode3 mode4 mode5  …

Question 1: Compute lateral stiffness of the one story frame with an intermediate realistic stiffness of the beam. The system has 3 DOFs as shown. Assume L = 2h and Elb = Elc   ans: given  it has 3DOFs, L=2h, El(b)=El(c) Question 2: For the following structures: Determine the number of degrees-of-freedom…

1)What is the mode of failure or damage of the beams in the figure above? Would you characterize the case as damage or as a failure? Are the damages repairable? Elaborate 1a)It is developed due flexural failure andconfining reinforcement failure Flexural damage is mostly associated with cracking and spalling of concrete…

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class. aim: Useing the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture…

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. aim: Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve   procedure: Open a new file  go to the manage tab and select Dynamo  open new file.search…

1) Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below           a. Using 3D model create a section box           b. To create similar doors and windows in a floor plan layout         …

 1.What are HVAC systems ? Why are they essential in modeling of buildings ans:  HVAC stands for heating, ventilation, and air conditioning This system provides heating and cooling to residential and commercial buildings. . The V in HVAC, or ventilation, is the process of replacing or exchanging air within a…

Create a G+4 Residential building as per NBC standards and make it a central model file. Your model should contain:The sloped roof at the top level of the building (10 degrees)Architectural components including furniture and home appliancesRoom tags and AnnotationsSection cut through each room either longitudinally or…

1) Select the type of structure you want to build from one of the three below        a. Multi Unit Residential Apartment        b. Office Buildings        c. School Ans:I will select the Multi Unit Residential Apartment from above 3 options. 2) Assume reasonable…

1:Aim:Based on the project saved from Week 3, proceed from First Floor Level .Model a Ceiling from architecture tab above the walls at first floor level procedure: a:open the week3 project from files menu load it. b:now open the architecture tool and select the celing option. c:we can see that celing tab will open rightcorner…

1.Aim:to Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, using floor tool under architecture tab and select the floor with appropriate material and thickness using the property browser create a layout in the Ground floor Level. Align the floor plan with grids…

1.BIM stands for building information modeling.cad is used for industrial design of mechanical and electrical assembels.while bim is used in the design and constraction of commericial buildings such as airpots,office etc.BIM model will allow for cad image to be viewable in full detail at one particular zoom level .cad…

1.AIM: From the file menu, create a new project (Structural / Architectural / Construction template ) and name the project appropriately PROCEDURE: A.Open file and click on new and select project B.select the required template c. we can name the project in project information tab REPORT: CREATED a new file with required…

1) Open an architectural template . Using Manage tab set project base point and project shared coordinates for the project. ans aim:to Open an architectural template . Using Manage tab set project base point and project shared coordinates for the project. procedure. a;open the architectural tab and select grids and rename…

1; Why are building codes or standards essential for the modeling/ efficiency of drawings in Revit ? ans: building codes or standards essential for the modeling/ efficiency of drawings in Revit becausesaftey,public health are linked with constuction of building.we know the every sholud follow codesbecause it is governament…