Final Project: Design of an Electric Vehicle

implementing code for controlling 'retraction' and 'extension' of Airplanes landing gear: program:          #include<stdio.h>           //header file     typedef enum               …

   code for union and intersection  of twp lists (list 1) and (list 2): program: #include<stdio.h>             //header file #include<stdlib.h>            //header file   struct…

For a 10-cell series lithium-ion battery model, simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB. AIM: To built a 10-cell series lithium-ion battery model, To simulate the thermal effects and compare life cycle performance at various temperatures,…

Create a MATLAB model of electric car which uses a battery and a DC motor. Choose suitable blocks from Powertrain block set. Prepare a report about your model including following Objectives:  System level configurations Model parameters Results Conclusion   AIM: To create a MATLAB model of an electric car with…

Battery pack capacity: 18 kWh Cell: ANR26650M1-B  Prepare a detailed battery pack drawing along with its enclosure. State your assumptions. AIM: To Prepare a detailed battery pack drawing along with its enclosure with ANR26650M1-B by a capacity of 18 kWh.  ANR26650M1-B is a Nano phosphate high power…

1.Simulate the 3 test cases from harness dashboard and write a detailed report on the results 2.What is coulomb counting? Refer to the above model and explain how BMS implements coulomb counting for SOC estimation?  AIM: - To simulate the Simulink model of a lithium-ion battery management system for 3 test cases and…

Part A: Search and list out the total weight of various types of aircrafts. Is there any difference between ground speed and air speed? Why is it not recommended to use aircraft engine power to move it on the ground at Airport?  How an aircraft is pushed to runway when its ready to take off? Learn about take-off power,…

Carry out a system-level simulation of an all-terrain vehicle.  Download the model from the given link:  https://www.mathworks.com/matlabcentral/fileexchange/70576-baja-all-terrain-vehicle-atv-model Prepare a technical report explaining the model properties & comments on the results.   Aim: To study…

Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium-ion cells. Give your detailed explanation on it AIM: To prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO,…

For a defined driving cycle, calculate the energy required for braking. Why electric motor can’t develop braking torque at high speed similar to starting? How electric and mechanical brakes are coordinated?  Make a MATLAB program which plots contour of given motor speed, torque and efficiency values. Attach…

A. Explain a MATLAB demo model named ‘Speed control of a DC motor using BJT H-bridge’.                                B. Comment on the armature current shoot-up from the scope results.             …

Which types of power converter circuits are employed in electric and hybrid electric vehicle?    An Electric Vehicle's powertrain with 72V battery pack in shown in the diagram below. The duty ratio for acceleration operation is 'd1' and for the braking operation the duty ratio is 'd2'.   The other parameters…

Aim: Use the power train block set to simulate the given conditions and plot the answers. Objective: What is the difference between mapped and dynamic model of engine, motor and generator? How can you change model type?  How does the model calculate miles per gallon? Which factors are considered to model fuel flow? …

AIM: Use ADVISOR tool and simulate the following  Objective:  For EV_defaults_in file, if cargo mass is 500 kg with all other default conditions, can the vehicle travel for 45 km with FTP drive cycle? Conclude your observations.  In the above case, try changing the battery capacity and repeat the simulation.…

Implement control logic of a “washing machine” using Stateflow as per given sequence:  If the power supply is available, the system gets activated  If the Water supply is not available, stop the process & indicate through LED Soaking time should be 200s followed by Washing time of 100s. Then rinsing…

Make a Simulink model of Doorbell using solenoid block with the Create a situation where the switch is closed for 2 seconds and then released. Observe the physical movement of the plunger. Make a Simulink model of doorbell using solenoid block Making a mathematical model of doorbell by using solenoid by Simulink…