Fender Design - Wheel Arch Challenge

Aim: To route the wiring harness on Given car body and Prepare flatten view drawing in CATIA V5.  Objective: This project shows that the route the Wiring harness on Given car body and Prepare flatten view drawing in CATIA V5.  Application of all Packaging rules, Industry best practices for the harness design.…

Aim: To route the wiring harness on given Engine and flatten view drawing in CATIA V5. Objective: The objective of the project is to route the wiring harness on given Engine and prepare flatten view drawing in CATIA V5. All types of packaging rules have to be considered while routing the harness. Also, Industry best practices…

                                                                   Wiring Harness Design in CATIA V5 -  3D modelling week 7 challenge  AIM:…

                                                                                           …

Aim: Route the harness layout in the Electrical workbench based on the input.  Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end) The above picture shows the 2D schematic layout of the required harness. DT06-4S (QTY-2) DT06-6S (QTY-1)…

                                                                                    Wiring harness routing…

                                                                                           …

                                                                                           …

                                                                                           …

                                                                                           …

                                                                                           …

                                                                                           …

                                                                                           …

 Aim: To modify for the given roof styling skin data, Develop the essential flanges and reinforcements, provide appropriate dimensions and check for Draft analysis. It also performs the roof calculations using by snow load Prediction formula and heat distortion of the Bow–roof prediction Formula. …

                                                                                   Section Modulus calculation…

                                                                                                    FENDER DESIGN REPORT Aim:    To design the BIW(Body In White) of the front fender using the fender skin data master section as the given data by using NX CAD. Fender:      Fender is the American English term for the part…

Aim:      This project shows that examine the given fender wheel arch design to verify if the wheel arch of the fender meets the European standards.  Fender Wheel Arch: Fender Wheel Arch is the sem-circular part positioned above the wheel of the vehicle. The most important body was a change that the…

                                                                                           …

                                                                                   Underbody coating and its purposes…

                                                                                           …

1. Radar Mast and Final Assembly of Yacht: Radar Mast Assembly of Yacht Render 2. Introduction: The project gives detailed instruction about the designing of different parts of a yacht-like   1. Propeller   2. Radar   3. BluePrint setup   4. Hull   5. Garage door   6. Front seat   7.…

1. REPORT ON ASSEMBLY OF CHOPPER MODEL DESIGN OF AMERICAN CHOPPER USING SOLIDWORKS 2. OBJECTIVE The objective of the project is to model an AMERICAN CHOPPER using CAD (computer-aided drafting) software-SOLIDWORKS and to render it with SOLIDWORKS visualize to create a photorealistic view of…

Aim: To Creation of CAD model considering Class A Surface, Nominal thickness, and Attachment strategy. Objective: To Creation of CAD model considering Class A Surface, Nominal thickness, and Attachment strategy. Create the mounting features as per design guidelines in the industry and with master sections Apply material…

Aim : The objective of this project is to develop a Closed Surface Model using Master Sections  To develop attachment features for Fixation of Parts by following OEM Design standards and   procedures in CATIA SURFACE WORKBENCH and PART DESIGN Description : Master Section : Master Sections are the guides…

AIM: Create the boss and Dog House for the Centre console coin holder. General Guidelines for Bosses:   Draft  - 0.5 degrees on walls of boss   Thickness -  Typically 40% * of the nominal wall at the base.   Height to Diameter Ratio -  3:1   Radii - 0.25mm maximum…

AIM: Create the rib for the Centre console coin holder.   RULES OF CREATING RIBS: PROCEDURE FOR  CREATING RIBS : STEP 1: Create an extract on the base surface. STEP 2: Sketch for creating rib. STEP 3: Extrude the sketch. STEP 4: Height of rib. The height of the rib should be 5*Thickness of components.  STEP…

Aim : Create the Core and cavity blocks for the switch bezel designed in the earlier challenge.  Procedure : Parting Surface Core Design Cavity Design Draft Analysis Procedure for Parting Surface : Extract the Class A surface boundary lines with boundary option. Extrapolate the Class A surface by 10mm. Trim the extrapolate…

AIM: Create the Coin Holder Plastic component through the given Class-A surface.  To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of the component to be 2.5…

Aim:         To perform  the draft analysis  of a fan cover using CATIA V5. Procedure: Steps involved:  A)Determining  and making the Tooling Axis: 1) Checking the boundary : The class A Surface is first checked  for its  boundary to find if there is any gaps or opening…