Fender Design Challenge

Objective:- To design outer panel of Hood with Hem and develop the Inner panel with all necessary reinforcements definition then positioning of Hinge, striker and create provision for mastic sealant points.   Theory:- The Hood or the Bonnet of a car is considered as the frontal BIW enclosure component. Bonnets are…

1.Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells.Give your detailed explanation on it ANSWER:- Introduction to lithium-ion cell and its types:- Lithium-ion is named for its active materials; the words are…

 Aim:- To route the wire harness on the given tailgate assembly and prepare the flatten view drawing on CATIA V5.  Objective:- The objective of the project is to route the wiring harness and prepare a flatten-view drawing for the given car body hatch. All types of packaging rules and constraints have to be considered while…

Aim:- To prepare a flattened view of a previously created harness assembly. Objective:- The objective of the given project is to create a flattened view for a harness assembly and then it on the drawing sheet. Steps:- 1. Defining harness flattening parameter. Firstly, we should make a new product file inside the electrical…

Introduction:- The wiring harness routing consists of an assembly of the geometrical bundle and electrical bundle. For mechanical wiring harnesses, the assembly of a geometrical bundle is the main component. For assembly of geometrical bundle, the connector, clips, grommets, must be electrically defined before entering…

Aim:- Route the following harness layout in the electrical workbench. Make an assumption for harness bundle diameter. Use the following connection as shown in layout. Also, add protecting covering on all branches connected to DT06-2S & DT06-4S connectors. keep and extermily at 30mm. Download connector data from te.com…

Aim:- To solve the above challenge question and define the necessary electrical properties in the respective workbench. Objective:- To download the P clamp and define it as electrical support in the electrical part design workbench and also define the necessary electrical properties. To download the Backshell and define…

Aim:- Define the given connector and connector clip as an electrical connector and add they're necessary properties using the electrical part design workbench in CATIA V5. Objective:- The objective of the project, download the given file from TE.com then define them as electrical connectors or equipment and lastly give…

Aim:- The main objective of the project is to write a program to evaluate the thermodynamic data such as specific heat, enthalpy, the entropy of NASA thermodynamic data to create the plots for all the species and to create the plots for all the species and to display the molecular weight calculation using MATLAB coding. …

Aim:-  To calculate the global maxima of a stalagmite function. Introduction:- Genetic algorithms are primarily used in optimization problems of various kinds, but they are frequently used in other application areas as well. Genetic algorithm is a procedure used in the field of Computer Science and operations research…

Aim:- Write a program that solves the ODE's for a simple pendulum mathematical model and simulates the pendulum motion. Governing equation:- where,  b=damping coefficient m=mass of body g=acceleration due to gravity  L=length of pendulum Simple pendulum:- A simple pendulum is a mechanical arrangement that demonstrates…

Aim:- To simulate the forward kinematic of 2R robotic arm using MATLAB. Objective:- Write a program to solve the forward kinematic of the 2R robotic arm. Introduction:- A robotic arm is a robot manipulator, usually programmable, with similar functions to a human arm. The links of such a manipulator are connected by joints…

Design of Metal Bracket:- Objective:- The aim of the project is to design a metal bracket and create a detailed drawing for manufacturing using siemens NX sheet metal application. Introduction:- The metal bracket is designed in NX 12.0 software by using sheet metal feature. Design Methodology:- Tools used while designing:-…

Designing A Bracket:- Objective:- To design a bracket using sheetmetal workbench of NX cad software. Introduction:- NX cad is simple and powerful tool which has wide varity of application in various industries such as automobile, aircraft, pharma etc.  Design Methodology:- Description:- Contour Flange: We need to…

Odd Shaped Encloser Objective:- To observe the model and design a sheet metal by using given dimension. Design Methodology:- NX cad is widely used software for multiple purpose like designing, engineering and manufacturing. It is used in various fields for different works. Different feature and methods we have designed…

Box Assembly Design On Siemens NX Cad Objective:- To design 3-D cad model of box assembly using NX 12. Introduction:- Sheet metal is one of the fundamental forms used in metalworking, and it can be cut and bend in variety of shapes. Everyday countless objects are made from sheet metal. Inside industry sheet metal plays…

Casing Design Using Siemens NX Cad Objective:- To design an advanced casing by usings sheet metal application in NX Cad. Introduction:- Sheet metal design is big domain and which is most use domain in industry. It more preffered in automotive industry. In this sheet metal casing design we will look at design approach using…

OBJECTIVE:- The objective of the project is to design a BIW back door of car with inner panel, outer panel and reinforcement for hinges, gas stay, wiper motor and latch by following the engineering standards. The inner panel must be subjected to draft analysis for verifying whether its satisfy the deep drawing requirement…

Aim:-        To Design a Car Roof and to do the curvature study to resist Heat distortion and snow load condition of the surface. Introduction:-         An automobile roof or car top is the portion of an automobile that sits above the passenger compartment. protecting the vehicle…

Section modulas Section modulas is the ratio of total moment resisted by the section to the stress in the extreme fibre. If the section modulas increase the moment of resistance increase and hence its load bearing capacity also. S=I/Y Section modulas gives us idea about how the load given structure can take. Where; S=…

Fender:- The fender is the part of the car directly over the wheel well which helps prevent debris and grime kicked up by the wheels from damaging the sides of the car or other nearby vehicles while you drive. The fender also protects the wheels from side impacts and other potential damage. Fenders are the curved strut…

1) Wheel Arch:- Wheel arch is the semi circular part of the fender positioned above the wheel of vehicle. The design of wheel arch of fender should be such that it must shield wheels and protect both passengers and pedestrains from projection of water ,mud, stone. For the vehicle to has its use permit in different countries,…

Underbody coating: Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if you are getting the undercoating applied after a couple of years, it’s…

Benchmarking: Benchmarking is defined as the process of measuring products, services, and processes against those of organizations known to be leaders in one or more aspects of their operations. Benchmarking provides necessary insights to help you understand how your organization compares with similar organizations, even…

AIM:- To create the Door trim considering the inputs given to me following the design rules and OEM standards. ABSTRACT:- The project deals with the explanation of steps and procedures followed while developing the Door Trim Panel of a car using CATIA V5. Using the class A surface I was able to create the tooling axis,…

                                       DESIGN AND ASSEMBLY OF QUICK RETURN MECHANISM 1)QUICK RETURN MECHANISM:-        A quick return mechanism is an apparatus to produce a reciprocating motion in which…

                                                          MASTER SECTION DEVELOPMENT Aim:- To design B pillar with the help of given master section to follow the design criteria…

                                                                 Door Applique Design Aim:- To create a solid body of a given Door Applique and to create the…

Aim:- To create the attachment features screw boss and dog house on the coin holder using the given design rule. Objective:- To design a screw boss by applying all design constraints. To design a dog house by applying all design constraints. To perform draft analysis. Screw boss design rule:- 1. Thickness(W):    …

                                             Attachment Feature Creation For Coin Holder  Aim:- To create Rib for centre console coin holder considering design rule. Objective:- The main purpose of the…

                                                                   DOOR ARM REST Aim:-  Creating the Door Arm Rest component through the given Class-A…

Aim:- To create a coin holder plastic component through the given Class A surface and performing the draft analysis on the model. Objective:- To ensure proper tree structure. To see overview of the model. Geometrical set having proper name. Total sketch should be in iso-constraned. Thickness of the component is 2.5mm.…

                                                               Core And Cavity Design Aim:-  To create a switch bezel from the given A-Class surface by considering…

DESIGN OF CLASS A, CLASS B AND CLASS C SURFACE OF SWITCH BEZEL USING CATIA V5 Aim:- The aim of this project is to develop the product design of the switch bezel with the help of the class A surface followinng the OEM standards. Introduction:- Class A:- Class A surface is the term mainly used in automative design industry,…

Title:- Base bracket design Aim:- To creat a Base Bracket plastic component though a given Class A Surface and perform Draft Analysis on the final plastic component. Objectives:- Creation of Tooling Axis. Creation of Class B and Class C surface. creating a solid part out of surface modeling. Draft Analysis of Class A surface…

DRAFT ANALYSIS ON A FAN COVER Objective:-The main objective  is to perform draft analysis to check if the part has the given draft on its all faces, and to determine the tooling axis. Draft:-It is tool used in CATIA to make the face taper with respect to tooling  axis. Tooling axis is the direction of mould part…

Radarmast:Yatch ReportTitle of project:-Design,assembly and rendering of yatch.Objective:-To learn sheet metal working and their design also learn inside the surface there will be different tool,by using the given tools we design the yatch model.Introduction:- A yatch is a boat which mainly used in ocean,river for fun…

Radarmast:   Yatch Report Title of project:-Design,assembly and rendering of yatch. Objective:-To learn sheet metal working and their design also learn inside the surface there will be different tool,by using the given tools we design the yatch model. Introduction:- A yatch is a boat which mainly used in ocean,river…

Aim & objective: To learn solidWorks software interface and simultaneously sketch or model the parts of American chopper. Apply appearance, scene, decals &material. Also apply the camera view, rendering to the vehicle, changing the background of vehicle with adjusting the shadow and daylight scene to the vehicle.…