Design of backdoor

The class A surface come separately and not together. Hence, we need to join them together and then start performing the design. Next Insert a geometrical set => To Create tooling Axis: Insert Geometrical set => tooling Axis extract the Base create a Point (Point type => on surface). Insert an axis system. Create…

Aim – Creation of B-Side features Heat Stakes and Locators for Fixation of Door Applique. Sketches: 4 Way Locator:   2 Way Locator: Heat Stakes: Heat Stakes – These are the features which we will have to make for connecting the part with the rest of the components,it may be another parts or fixation plane or etc. The same…

General Guidelines for Bosses:   Draft  - 0.5 degrees on walls of boss   Thickness -  Typically 40%* of the nominal wall at the base.   Height to Diameter Ratio -  3:1   Radii - 0.25mm maximum radii.   "C" is where the doghouse contacts the backside of the…

Aim – Development of a Car B pillar cover, and making B – Side features as per given Master Section. Introduction – In the industry, when there is Designing of a new part for the car or Re – Designing the same, there are so many considerations which are taken care of with the help of Master Sections.…

I am an internal employee of Skill-Lync and I have worked on 'Automotive seating design and development Project using Catia v5' and I will be submitting the project for this course.

The full form of OEM is original equipment manufacturer.  OEM - Tier 1 - Tier 2 - Tier 3 -Tier 4. Aptiv, Cummins are an example and they provide design solutions. The first car was made on January 29,1886. Wooden seats were used in the first car. The 3d reference system is used to locate all the components in a vehicle…

I am an internal employee of Skill-Lync and I have worked on 'Automotive BIW Design using CATIA' and will be submitting the project for this course"

I am an internal employee of Skill-Lync and I have worked on 'Automotive BIW Design using CATIA' and will be submitting the project for this course"

I am an internal employee of Skill-Lync and I have worked on 'Automotive BIW Design using CATIA' and will be submitting the project for this course"

I am an internal employee of Skill-Lync and I have worked on 'Automotive BIW Design using CATIA' and will be submitting the project for this course"

I am an internal employee of Skill-Lync and I have worked on 'Automotive BIW Design using CATIA' and will be submitting the project for this course"I have attached the catpart for the back door design.

I am an internal employee of Skill-Lync and I have worked on 'Automotive BIW Design using CATIA' and will be submitting the project for this course"I have attached the catpart down below

I am an internal employee of Skill-Lync and I have worked on 'Automotive BIW Design using CATIA' and will be submitting the project for this course"

I am an internal employee of Skill-Lync and I have worked on 'Automotive BIW Design using CATIA' and will be submitting the project for this course"

  Constructing the tooling axis line: Extract the base of the part. Take intersections of the class A along the xy and yz plane. Next using the intersections, construct two lines along the side walls and use bisecting line command with respect to the two lines constructed along the side walls. This way you will be…

Core and Cavity Design Draft analysis: PARTING SURFACE AND PARTING LINE: Different Views:

Report:Tooling axis creation: First extract the base surface. Then create a point on surface at the center (0 mm). Insert an axis system. Use intersect command and take an intersection of the class A surface and YZ plane. Again take an intersection of class A surface and XY plane. Now create a sketch at YZ plane and use…

In a (.IGS) File the class A surface come separately and not together. Hence, we need to join them together and then start performing the design. But the design has few error surfaces and we keep getting topological errors. To correct it we need to follow to following steps. Tree structure:    Class A surface…

 Draft Analysis:  The Draft Analysis command helps us detect if the part you drafted will be easily removed from the moulding process. This type of analysis is performed based on indentifying zones on the analyzed element where the deviation from the draft direction at any point, corresponds to the specified…

AIM: Create a Rankine Cycle Simulator using MATLAB. Your code should calculate the state points of the Rankine Cycle (any type of your choice) based on user inputs. Then, plot the corresponding T-s and h-s plots for the given set of inputs. Title and axes labels are a must, while legends could be used if necessary. Attach…

  AIM: g = gravity in m/s2, L = length of the pendulum in m, m = mass of the ball in kg, b=damping coefficient. Write a program in Matlab that will simulate the pendulum motion. use, L=1 metre, m=1 kg, b=0.05. g=9.81 m/s2. Simulate the motion between 0-20 sec, for angular displacement=0,angular velocity=3 rad/sec…

OPTIMIZATION OF A STALGAMITE FUNCTION AND TO FIND GLOBAL MAXIMA OF THE FUNCTION USING GENETIC ALGORITHM WHICH IS EXECUTED IN MATLAB. AIM: To explain the concepts of Genetic-Algorithm and the syntax of GA used in Matlab. To Write a code to optimize the stalagmite function To Find the global maxima of the function. To make…

AIM: To write a function that extracts the 14 coefficients and calculates the Enthalpy, Entropy, and Specific heat for all the species in the data file. (the first 7 coefficients are high-temperature coefficients and the second 7 coefficients are the low-temperature coefficients). Calculate the molecular weight of each…