Design of backdoor

Design of Backdoor Objective:  To design Back door of car using the given Class ‘A’ surface. Introduction      It is a hinged board or door at the rear of the vehicle that can be moved up or down during loading and unloading. Back Door is also referred as 'Hatch' or 'Tailgate' or 'Trunk-lid' or 'Boot-door'. Its the rearmost…

Design of Backdoor Objective:  To design Back door of car using the given Class ‘A’ surface. Introduction      It is a hinged board or door at the rear of the vehicle that can be moved up or down during loading and unloading. Back Door is also referred as 'Hatch' or 'Tailgate' or 'Trunk-lid' or 'Boot-door'. Its the rearmost…

ROOF DESIGN OBJECTIVE : The objective of this project is to design car roof with  essential flanges and reinforcements  like ditch area , front roof rail , bow roofs, central roof rail and rear roof rail for the the given styling surface Perform a curvature study on the roof and perform the calculations for the heat distortion…

FENDER DESIGN OBJECTIVE The main objective of this project is to design a fender using a new age design software-NX-CAD INTRODUCTION: Aluminum automotive components made using a hot blow forming process are reducing vehicle weight and increasing the fuel efficiency of today’s cars. However, before General Motors…

Wheel Arch gap - Calculations   Aim :      To calculate the wheel arch gap at required points and check whether the car passes the European standard. Objective : Study about the different wheel arch gap standards. Draw the lines at the required angle and points for the European standard. Measure the…

                   Section Modulus Calculation Of Hood Aim  To calculate the section modulus of the previously designed hood for analyzing its strength and also optimizing the design to see the difference in the bending strength of the hood. Higher the section modulus of a structure, the more the resistive it becomes to…

DESIGN OF HOOD ASSEMBLY AIM:                 To design the hood inner panel and to fix the striker in path of the trajectory of hinge axis. INTRODUCTION:                 Hood…

DOOR TRIM LOWER Aim: To Create the Door trim lower component through the given Class-A surface. Objectives: • Creation of Tooling axis with appropriate draft angle. • Creation of other surfaces (eg, B and C surfaces) for creating a solid component. • Perform Draft analysis on Class A surface and Solid model…

Underbody coating in an automobile Underbody coating is a rubberized paint that forms a 2-3 mm thick coating all along the underside of the body. You also get a thinner clear coat underbody coating which is like a lacquer that coats the entire underside of the car. Some even inject rust-preventive coating material into…

AUTOMOTIVE BENCHMARKING Benchmarking is the process of comparison of similar products on some dimensions of performance Automotive Benchmarking is the process of analyzing the choices of similar products based on the selection factor and deducing it to final conclusion. CASE Mr. D.S. Pughazhyendhii is a married man…

BUMPER DESIGN AIM: to make a model from the provided class-A surface.INTRODUCTION:CLASS-A SURFACE: a surface made by the designer which is given as an input to the plastic modeler to work on. It is aesthetic surfaceand the outer most surface.CLASS-B SURFACE: a surface below a certain thickness from the class-A…

                         SCREW BOSS AND DOG HOUSE  AIM :          To create the boss and dog house for B-side feature and create under design rules. SOFTWARE USED :  CATIA V5 SCREW BOSS :   Draft  - 0.5…

AIM :         To create rib for center coin holder by using design rules. SHORT NOTE :         We know that class A is an aeasthatic aurface and class B is an engineer surface,In class B contain all enigineer data.Here some desigining feature they are  Ribs Screw boss design…

AIM :        To create core and cavity design for SWITCH PANEL BEZEL. SOFTWARE USED :   CATIA v5 PROCEDURE : Take boundary by using class A surface  and then extrapolate .  Join extrapolate surface with class c and trim it off.with the trim surface join class B surface and create…

AIM:        Create coin holder design through class A surface. PROCEDURE : First create tooling direction by using class A surface. Keep class A as a reference to create class B and class C surface. Join class A and c together and class B surface and trim it. Finally analysis tooling direction by draft…

AIM Route the Wiring harness on Given car body and Prepare flatten view drawing in CATIA V5 1.Download the back door and covert into CAT.file 2. Define the Furr tree clip   3.Define the connectors     4.Assemble the connectors and furr tree clips 6.Route the bundle segement from the main interconnector 7.Check…

Aim  To Route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5   Objective Route the wiring harness for V-16 engine Prepare flattaen view drawing in CATIA V5 Apply all packaging rules and industrial best practice Provide all necessary details like clearance, clipping/clamping selection, harness…

Q1. Flatten the harness assembly. Place the flattened view on drawing sheet. Ensure bundles with protective coverings has different visuals on drawing view. Harness assembly       Flattening parameters     Geometrric bundle is extracted for flattening and converted into "EHF"     Assembly is falttened   Drafting of flattened…

AIM: Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Followingconnectors as shown in layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (fromconnectors end) Steps to be followed:…

Aim : To define given P clamp CAD data as an electrical support using electrical part design workbench & define all the necessary properties. To define given Backshell CAD data as an electrical backshell using electrical part design workbench & define all the necessary properties. To create COT tubes with outer…

Wiring harness design in CATIA V5 - 3D modeling CONNECTOR MODELINGDownload the specified connector from te.com. In the part design workbench provides the center point and axis system to the wire inserting end and connection end. The axis must be given in a specified way: X-axis: Towards the clamp Y-axis: Towards the connection…

      Final Assembly of Yacht Objective:-Design the individual components of a yacht and assemble them together by using solidworks. Introduction:-A yacht is a watercraft used for pleasure or sports. The term originates from the Dutch word Yacht, and originally referenced light, fast sailing vessels that the Dutch Republic…

Assembly of American chopper: Objective:To design individual parts of an American chopper with fully defined sketches and appropriate appearances.To assemble all the individual parts of the American chopper to create the chopper model.To render the chopper model by adding appearances, decals, lights, cameras, and background…