model: inside model: requirement1 subsystem: requirement2 subsystem: sldd file: model advisor: code generation:

Answer: Aim: To develop an Adaptive Cruise Control feature as per the Requirement Document using MATLAB Simulink   About: Adaptive Cruise Control Feature for passenger cars allows the host vehicle to adapt to the speed in line with the flow of traffic. Driving in heavy traffic or keeping a safe distance to the preceding…

  1.a detailed report was provided regarding the requirements of the model to be developed  2.The simulink model is  developed as per the requirement 3. the database is created as per the requirement that is an sldd file and the database is linked requirement tagging is done and the report is generated 4.embedded…

Answer 1: In the ADVISOR tool EV_defaults_in file is loaded with cargo mass 500 kg has been setup. and now select continue, change the drive cycle to cyc_ftp with 3 cycles.and click on run, here the vehicle stops after completing 41.4 kmsso it has failed to reach the 45 kms. Answer 2: now we change the battery capacity…

Question 1:- What is the difference between the mapped and dynamic models of engine, motor and generator? How can you change the model type?  a)What is the difference between the mapped and dynamic models of engine, motor and generator? Answer:- Mapped Model:- The mapped model is one type wherever the information…

 Answer1: In the past decades, power device technology has made a tremendous progress. These power devices have grown in power rating andperformance by an evolutionary process. Among existing power devices, including the thyristor, gate turn-off thyristor (GTO), power bipolarjunction transistor (BJT), power metal-oxide…

 Answer1: A: SPEED CONTROL OF DC MOTOR USING BJT H BRIDGE: A DC motor spins either backward or forward, depending on how you connect the plus and the minus.If you close switch 1 and 4, you have plus connected to the left side of the motor and minus to the other side. And the motor will start spinning in one direction…

Answer1: A driving cycle is a series of data points representing the speed of a vehicle versus time. Driving cycles are produced by different countries and organizations to assess the performance of vehicles in various ways, for instance, fuel consumption, electric vehicle autonomy and polluting emissions calculate the…

PART A: ANSWER1: a)Aircraft Gross weight: The aircraft gross weight (also known as the all-up weight and abbreviated AUW) is the total aircraft weight at any moment during the flight or ground operation. An aircraft's gross weight will decrease during a flight due to fuel and oil consumption. An aircraft's gross weight…

Electric Vehicle (EV) An electric vehicle (EV) is a vehicle that uses one or more electric motors or traction motors for propulsion. An electric vehicle may be powered through a collector system by electricity from off-vehicle sources or may be self-contained with a battery, solar…

Answer1: Lithium Cobalt Oxide (LCO): Cobalt oxide is used as a Cathode terminal. and Graphite carbon is at the anode terminal. these batteries have short life span. and these are having low thermal stability.   Lithium Manganese Oxide(LMO): Here Manganese Oxide is acting as the Cathode It has a three dimensional Architecture.…

Answer1: Test case 1 click on test sequence Variant block  then select test case 1  now click the BMS_StateRequest block  from the above chart, we see that Driving is for 3000sec Balancing is for 1000sec and  PostChargeBalnceing is for 5000sec  now we are running…

AIM:  Prepare a detailed battery pack drawing of [Battery pack capacity: 18 kWh, Cell: ANR26650M1-B] along with its enclosure. State your assumptions. Details of Cell: ANR26650M1-B:   ANR26650M1-B specification: Nominal Rating: voltage :3.3 volts capacity:2.5Ah energy: 8.25Wh specific power: 2600W/kg impedence(1KHz AC…

Answer: AIM: Thermal Modeling of Battery Pack. Objective:  For a 10 cell series lithium ion battery model, simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB. Introduction: The performance and life-cycle costs of electric vehicles…

Answer1: SOLENOID:  A solenoid is a three-dimensional structure of wire. When this wire is wrapped around a metallic block in a coil and current passed through it it has some special magnetic properties Electromagnetic induction makes it an electromagnet that can be switched on or off. The side in which the current…

ANSWER1: WORKING PRINCIPLE OF A WASHING MACHINE:-  The working principle of a washing machine is centrifugation. Centrifugation is a separation process that uses the action of centrifugal force to promote the accelerated settling of particles in a solid-liquid mixture. The washing machine consists of a centrifuge for this…

AIM: To carry out system level simulation of all terrai vehicle. To study the BAJA ATV model with lookup table and with out lookup table. model: BAJA ATV The input parameters: brake and throttle inputs: the brake is not applied throttle input is 0.5 through out the 80 seconds GENERIC ENGINE: this engine incorporates the…

AIM: Design of an Electric Rickshaw using MATLAB Simulink ABSTRACT: In this project, we work to create the MATLAB model of the ELECTRIC RICKSHAW by doing a PM brushed type DC motor and a suitable Lithium-Ion battery for the motor. Before this, we will remember what is Electric RICKSHAW, how it's functioning and…