Vishal Kumar
AUTOMOBILE ENGINEER ||CAE & FEA || COMPUTATIONAL STRUCTURAL ANALYSIS || ADAS(Advanced Driver Assistance System )|| VEHICLE DYNAMICS|| NUMERICAL ANALYSIS USING MATLAB || MODEL BASED DESIGN USING SIMULINK
Skills Acquired at Skill-Lync :
Introduction
10 Projects
VOLUME MESHING OF TURBOCHARGER USING ANSA
OBJECTIVE Geometry clean up and meshing of the Turbocharger using the TRIA element type. PROCEDURE 1. STEPS TO OPEN A FILE IN ANSA Click on File Select Open Select File (FORMAT .igs/SLDPRT .ansa etc.) Click Open A translator window appears CLICK OK As the part gets opened in ANSA, firstly it is in wire mode…
21 Nov 2019 02:38 PM IST
ADVANCED MESHING OF BMW M6 MODEL USING ANSA
OBJECTIVE Geometry clean-up and meshing the BMW M6 model for performig CFD using ANSA ABSTRACT As in this project we will be meshing the BMW M6 model in the wind tunnel before meshing the geometry, it should be cleaned and all the topological errors should be rectified so firstly we need to look for all the geometrical…
21 Nov 2019 02:39 PM IST
2D Shell Mesh and Mesh clean-up of Elements using hypermesh Radioss
OBJECTIVE Performing 2D Mesh and Mesh clean-up of Elements using hypermesh Radioss of the given geometry Practice Clip Repair Mounting Bracket ABSTRACT In this project we need to clean up the geometrical errors and create a mid surface of the given geometry, perform 2D shell meshing for the structural analysis…
21 Nov 2019 02:38 PM IST
CYLINDER SURFACE 2-D MESHING USING ANSA
OBJECTIVE To mesh the given model using the spot mesh tool, using element type tria and the element size of 1 unit. PROCEDURE STEPS TO OPEN A FILE IN ANSA Click on File Select Open Select File (FORMAT .igs/SLDPRT .ansa etc.) Click Open A translator window appears CLICK OK …
21 Nov 2019 02:39 PM IST
Transient Behaviour Of A Simple Pendulum Simulation Using MATLAB
Transient behavior of a simple pendulum using MATLAB The figure shows the moton of the pendulum, a bob is suspended by a massless string from a fixed point. Let us assume, m= mass of the bob l= length of string Equation for the damped motion of the pendulum is given below …
25 Apr 2020 03:37 AM IST
MESHING THE PRESSURE VALVE WITH DIFFERENT ELEMENT SIZE USING ANSA
OBJECTIVE To mesh the given pressure valve model using ANSA with various element size of 15mm 7mm 2mm TOOLS USED DURING THE PROCESS Not function ! Not function All function Lock function Invert function Coons (Under Surface) Intersect (Under Faces) Loop function Feature Area PROCEDURE STEPS TO OPEN A FILE IN ANSA…
21 Nov 2019 02:39 PM IST
SOLID TETRA MESH OF HOUSING, 3D HEX ELEMENT MESH OF ARM BRACKET GEOMETRY AND EDITING ENGINE FILE USING HYPERMESH RADIOSS
OBJECTIVE To check the material properties of the rail and calcuate, the speed of sound in steel rail, time taken for the shockwave to travel the entire rail and time of sound to travel length of rail. To edit the engine file in radioss and set the frequency of animation output to a time that will give 20 animation…
21 Nov 2019 02:38 PM IST
CLEANUP THE GEOMETRY AND MESHING THE FRONT HOOD FOR STRUCTURAL ANALYSIS
OBJECTIVE Clean up the Hood geometry and then mesh the geometry with the element size of 5 mm for structural analysis using ANSA ABSTRACT In this project we need to clean up the geometry of the inner panel and outer panel surface of the hood and then extract the mid-surface and perform hemming process on the mid surface…
21 Nov 2019 02:39 PM IST
TO DEVELOP AN ADAS FEATURE FOR COLLISION MITIGATION BRAKING SYSTEM (CMBS) USING MATLAB SIMULINK
OBJECTIVE TO DEVELOP A SIMULINK MODEL FOR ONE OF THE ADAS FEATURE OF COLLISION MITIGATION BRAKING SYSTEM (CMBS) ABSTRACT In this project we need to develop a model based design using Simulink for the feature that the CMBS should get deactivated while the vehicle is moving in reverse direction/reverse gear. The Simulink…
11 Nov 2020 03:16 PM IST
To Calculate Natural Frequency At Three Different Load Condition To Attain A Flat Ride Bump Oscillation Of A Vehicle Using MATLAB scripting.
OBJECTIVE To calculate natural frequency at three different load condition attain a flat ride bump oscillation for a given vehicle dimension using MATLAB scripting. ABSTRACT Ride frequency, derived straight from natural frequency, is the suspension frequency found in cars. This is how fast the suspension travels up…
29 Sep 2020 04:44 PM IST
1 Course Certificates
Introduction to Model-Based Development using MATLAB and Simulink
Here are the courses that I have enrolled
Similar Profiles
Ladder of success cannot be climbed with hands in pocket.
The Future in Motion
Give more than what you get you will get more than what you gave
Avid learner