AIM :  To write a Matlab program  to calculate drag force against a cyclist and plot:   Velocity vs  Drag force.   Drag coefficient vs Drag force.           ( Using Octave  4.0.0 GUI )   GOVERNING  EQUATION : The equation for the 'drag force'…

AIM :  To write a Matlab program to solve the ODE  which represent the simple pendulum motion and the create animation file of the simple pendulum.           ( Using Octave  4.0.0 GUI )   OBJECTIVE OF THE PROJECT: Our main objective is to solve ODE of the simple…

AIM :  To write a Matlab program code to fit a linear and cubic polynomial for the Cp data and plot the linear and cubic fit curves along with the raw data points.           ( Using Octave  4.0.0 GUI )   OBJECTIVE OF THE PROJECT: Our main objective is to…

AIM :  To write a Matlab program  to simulate the forward kinematics of a 2R Robotic arm and to create a animation file.           ( Using Octave  4.0.0 GUI )   ABOUT 2R ROBOTIC ARM  :                    …

AIM : Write a code in MATLAB to:       1. Optimise the stalagmite function.       2.Find the global minima of the function.       3.Plot graphs for all 3 studies and for F maximum vs no. of iterations.   OBJECTIVE OF THE PROJECT: Our main objective is to know…

AIM : Parsing of NASA thermodynamics data file.           ( Using Octave  4.0.0 GUI )   OBJECTIVE OF THE PROJECT: Our main objective is to : 1.Write a function that can extracts all the 14 co-efficients and calculates the enthalpy, entropy and specific heats for all…

AIM : To create a Rankine Cycle Simulator.           ( Using Octave  4.0.0 GUI )   OBJECTIVE OF THE PROJECT: Our main objective is to : To calculate the state points of the Rankine Cycle.  To plot the corresponding T-s and h-s plots for the given set of inputs.…

AIM :  MBD simulation of a piston assembly.    OBJECTIVE OF THE PROJECT: Our main objective is to design a 3D model for various parts of the piston assembly, simulate it and plot the graph. Also to model different wrist pin offset which are: 1. 0mm offset at 2000 crank rpm. 2. 10mm positive offset if crank…

AIM :  MBD simulation on IC  Valve Train.    OBJECTIVE OF THE PROJECT: Our main objective is to design a 3D model for various parts of the vlave train, simulate it and plot the graph. Also to run the simulation in different cam lift which are: 1. 3.6 mm cam lift for 1500 rpm and material cast carbon…

AIM :  To perform flow simulation in a pipe with different Reynolds numbers.    OBJECTIVE OF THE PROJECT: Our main objective is to run a pipe simulation with Reynolds numbers  100 , 1000 and 10,000 also:   1.  To place line probes at 95%, 90% and 85% of the pipe length. 2.  To compare…

AIM :  To perform transient flow simulation over a cylinder.    OBJECTIVE OF THE PROJECT: Our main objective is to run a transient simulation over a cylinder with  a baseline simulation and then calculate the Reynolds number. Then increase the Reynolds number by a factor of 20%, 40%, and 100% then run…

AIM :  To design and analyse the centrifugal pump.    OBJECTIVE OF THE PROJECT:  Our main objective is to obtain the performance diagram of the designed centrifugal pump and obtain the relationship between pressure ratio and mass flow rate where pressure ratio is the ratio of the outlet total pressure…

AIM :  Modelling and simulation of flow through a flowbench.    OBJECTIVE OF THE PROJECT:   Our main objective is to :     1. Perform grid dependence test for three grids after that running simulation at a particular valve lift and explaining the results.     2. Effect of valve lift…

AIM  - To  do comparing of bending of beams.   OBJECTIVE OF THE PROJECT : Our main objective is to compare the performance of the given three different beams which are rectangular beam, I-section, C channel.   ABOUT BEAM: A beam is a structural member which is used to bear loads applied to them. It…

AIM  - To  Do Analysis Of Buckling Phenomena.   OBJECTIVE OF THE PROJECT : Our main objective is to:  Perform a buckling analysis on a cyclonic separator stand.  Create a stiffener on the legs of the stand and run the analysis to find out the change in buckling factor of safety.  To perform…