Lesson finished
Lesson finished
Lesson finished
Lesson finished
Unlock all 12 lessons of IC Engine Calibration using GT-POWER and GT-SUITEFull course ₹40,000 · paid
SI Engine Case Study: Four-Cylinder Model Setup from an Example File
A free lesson from Skill-Lync's IC Engine Calibration using GT-POWER and GT-SUITE course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “3.0 - SI Engine Case Study - Part 1”
What will you learn in this free IC Engine Calibration using GT-POWER and GT-SUITE lesson?
This case study builds a four cylinder, 16 valve naturally aspirated engine with 73 mm bore and 89.4 mm stroke, starting from a GT-POWER example file. It reviews the intake, throttle, cylinder, heat transfer and combustion settings, the 50 percent burn point as a function of speed, valve lift, friction and swept volume, then sets up full load runs at 6600 and 4600 rpm.
- Starting a model from a GT-POWER example file
- Choosing compression ratio based on available fuel octane
- Defining 50 percent burn point as a function of speed
- Setting up full load cases and swept volume check
What comes after lesson 3?
Later in Skill-Lync's IC Engine Calibration using GT-POWER and GT-SUITE course (paid): lesson 4, CI Engine Modelling Techniques - Part 1; lesson 5, Case study on CI engine - Part 1; lesson 6, Turbo Charge Modelling - Part 1. The full course has 12 lessons (18 h 43 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Part 1
Hello, welcome to our session number 3. Under the course, IC Engine Modeling using GT-POWER, 1-Day System Simulation. So today we are going to have the case study on SI Engine. Now in last two sessions, first session was about the introduction to the GT-POWER. Then we saw assignment number 1, where you got introduced to different settings. Assignment number 2 was SI Engine Modeling Techniques, where along with the software, we also went through the basics of SI Engine Combustion. Now we are going to touch a case study on SI Engine. It's like how maybe I have selected one engine and not name it. But now we are going to model that and then we are going to see how to model it using a GT-POWER and how to get the feasible result.
Okay, so let's get started. So this is what engine we are going to build. It's a 4-cylinder SOHC, that is a single overhead camshaft with 16 valves. So 4-cylinder 16 valves means obviously 4 valves per cylinder. So that is 2 intake and 2 exhaust. The bore of the engine is 73 mm and the stroke is 89.4 mm. It's a naturally aspirated and water cooled engine. The rated power is 87.7 kilowatt at 6600 rpm. And it is 145 Nm max torque at 4600 rpm. So now we have to do a thermodynamic simulation.
So when I say the thermodynamic simulation, what we are going to assume is that we will get the required temperatures, we will get all the mechanical side, everything is okay. There is no water and dynamics issue and we get the required watt timings, the camshaft, crankshaft, everything is perfect. So only we are going to focus on the thermodynamic simulation. That is on the power, torque, the heat transfer rate, the combustion model, and whether my MFB 50s are correct, whether my volumetric efficiency is correct, gas exchange, the pumping losses.
What about the BSFC range? So let's get started. So now always a question. What is important for a combustion? Whether it is air or fuel or it's like air fuel mixture. What is the limiting factor because of which we have the limit on the torque, which we can derive from engine or power? So the answer is it's not fuel. It is definitely air because burn of fuel, what we required is air. The amount of oxygen which is required to burn is taken from the air. But unfortunately with air, what comes is a nitrogen also N2 and then at high temperatures, there is a dissociation of the N2 into NOx and which is unwanted and which comes out as a pollutant. So it's like we have to always balance. If my amount of air is more than the required, what that is what we call as a lean mixture, the amount of N2 will be on higher side and therefore the NOx formation will be on higher side. If my mixture is rich, then obviously the amount of oxygen which is required to burn completely is not there. And then my pollutant formation will be CO that is carbon monoxide and hydrocarbon. So always we have to balance and that balance is nothing but what we call is a calibration. So we have to calibrate the engine to get the required performance and emissions both. So always it is the amount of air which will decide how much fuel we can burn in the cylinder and therefore the amount of torque which can be generated when we burn the fuel. Now how this air fuel mixture is important because this see it's like fuel gets mixed with the air and then that air fuel mixture is formed in case of SI engine. If it's a port injection, then we inject the fuel in the port that gets mixed with the air. So it has enough time it travels through the cylinder during intake wall opening. Then when during the compression it gets operated and then we get the homogeneous mixture and then towards the end of the compression what we do is we initiate the spark plug and then there the flame is started and then that flame travels and completely engulfs the complete mixture. Now if there is like air fuel mixture is not homogeneous this is at some parts if it is rich then the chances that it will not burn completely and it will come out as a CO and HC hydrocarbon. Generally this is not a major issue with the SI engine because we have enough time for air fuel mixture. This is a major issue with the diesel engine maybe that we can see during a CI combustion. So now let's go to the engine model. Now here I have the different way approaches of starting a engine modeling. So now we it's our task is that we have to model a four cylinder SI engine.
So we have some basic data available. Now there's a difference right when as a student if I am doing this the problem is that the availability of the engine data. So a lot of data is not available with us but no problem we can start with very basic model and slowly slowly we can build on that. Generally when if you are in a company and then you are starting a engine model definitely you have a lot of inputs available with you. So but let's say if you go to internet and just search by any engine which is your favorite it can be let's say from multi-air it can be honda i-b-take a dream series or maybe something else let's say it's from mercedes bmw. So get the basic data and then we can start with that.
So as a student when we are learning the software the accuracy of the results are not important I would say maybe we cannot talk about the accuracy at this moment it's about that building the model a feasible model last time we have seen that even if I put compression ratio of 19 GT-POWER will run it and then it will show that you have very good bsfc so but that is not feasible obviously with the si engine we cannot operate with this high compression ratio so what I mean a feasible model is nothing but inputs which are feasible so it's like you have to read some textbooks get some data get some examples from the textbook or we can try to reproduce using the GT-POWER so any any as engine textbook if you remember we use in engineering we used to solve this if this is a compression ratio what is the in cylinder pressure max pressure it will let you what will be the temperature how much will be the indicated work brake power so we used to do this manually right now we have this computer with us we have this GT-POWER tool so we can solve all those examples from the textbook using the GT-POWER so you can start doing this slowly slowly so now when I say the modeling approach so what I recommend to the students is instead of starting from zero what we can do is we can start from an example file and then we can change our input initially so we need not to bother like which data we have to put so maybe we can explore that model we can understand okay how they have modeled the port how they have modeled the manifold runners cylinder heat transfer model which combustion model they have selected what data they have put so we can get the idea of those things and then slowly slowly we can move instead of taking the example file we can then directly start from the scratch then we are aware that which template we should select and then which object we should create out of the template and then which models we should use which thermal model i should prefer which combustion model i should use so that slowly slowly you will get the idea of that obviously uh the some reading is required so it's like i as i said if you want to learn GT-POWER the best phase you can start with the tutorials and then slowly move to the examples and for each and every templates uh the help is available and GT-POWER is very strong in that it's like with the usp of the GT-POWER is that their help and documentation is very good and the support is also very good so now i'm going to show a approach where i recommend is uh we can start with the example file so now as i said if you go to the examples now there are a lot of examples available right so it's the examples on acoustics aerospace after treatment kb embodiment different different different on engine then vehicle transmission water and so many things so let's get started with this engine modeling so now here you will find the two groups one is engine 0d sil and hl sl and hl is nothing but the software in loop and hardware in loop where the model fidelity and the model uh solving time so it should be as fast as possible so basically this kind of approach is used uh for when your interest is that you want to use the model for calibration or let's say control strategy development where the speed of the solving time is important so this is one group sl and hl what they call there is frm and mean values it is frm we are going to touch in one of the session so there i will talk in detail about that the second group is this engine 1d gas exchange combustion so there are different again examples on acoustics after treatment boosting charger pulling then there's a separate group of diesel engine crank train engine engine start stops it's it comes under the hybrid what do you call then this is a gasoline So there is a separate group of gasoline and then you will find the natural gas. So this gasoline and natural gas comes under this SI principle.
So we have understood why this gasoline and natural gas works on SI principle. It is basically due to that it has a very high octane number and high octane number indicates what? It is a slow burning. And therefore, if I use the spark plug to initiate the combustion, definitely the combustion will be slow. The flame will initiate it at the spark plug and then it will travel along the cylinder and then it will burn the air fill mixture. So there won't be any combustion simultaneously or self-ignition simultaneously happen at the other place and then chances of knocking will be very less in case of high octane number.
And if I use, let's say, diesel into, if I want to work on SI principle, definitely it is going to knock because there are chances that because high octane number indicates it is a fast burning, those chances that there will be another flame or there will be another initiation, self-ignition at other place and then these two flames will travel opposite to each other and then it will lead to the knock. So that's the simple reason. So that's the simple reason. So basically we have these two groups, gasoline and natural gas. So natural gas is nothing but compressed natural gas, what we call SI natural gas. So there are two examples available there. And in gasoline, we have a lot of.
So we have four cylinder basic, we have four cylinder EGR controller, GDI, GDI supercharger. So now in our case, I have not mentioned whether the engine is GDI or whether it is a port injection. So maybe we can assume that this is a GDI engine and then we can start this four cylinder GDI engine. Okay. And then even I have not mentioned whether it is a supercharger, turbocharger engine, nothing, because there is no simple solution or simple formula by which I would say if I just put everything and then I can derive the engine configuration, there are multiple ways like different, different strategies, like whether I should use turbocharger, whether I should use supercharger or whether I should go with the nationally aspirated engine.
So that depends like what configuration or what BMP. So the one terminology that is very important to find out whether I should go for the turbocharging is not or not is BMP. So the thumb rule is that if BMP, I want to go that BMP is nothing but to break main effective pressure. If I want to go above, let's say eight or nine bar of BMP, I should prefer the turbocharging because it's very difficult to achieve this BMP level with naturally aspirated. So there are some thumb rules which maybe you will get acquainted slowly, slowly if you start reading and then you can have your thumb rules for different, different configurations readily available.
So what I am going to do here is I am going to start with the example file and then accordingly I am on. So now I am going to choose this four cylinder GDI engine. So if I double click, it will open. Now, as I said, when you are opening from the example software, the first thing you should do is you should do a save as because we don't have any rights to change there. So we'll go to our folder. So now this is our session number three.
Already I have saved and done some changes. But okay, anyways, we are going to start again. So now this is my model is completely ready. It's a four cylinder. What we can see is it's a four cylinder engine. Correct. And then this is a naturally aspirated engine because there is no turbocharger here. So it's directly from the ambient. It goes to the air filter and then from air filter directly, it goes to the manifold. And then from manifold, it goes to the cylinder, then exhaust directly from exhaust manifold, it goes to the catalytic and also there is no turbocharger in the picture.
So that turbocharger, we have a separate session there. I will talk about what is the turbocharging, supercharging and then which we should prefer. So now these things you won't get in the GT tutorials, for example, files. They will directly just, they will focus on the GUI, how to use the, how to do the modeling, but they will not give you inside like the thumb rules or like which one supercharger is better or turbocharger is better. Under what category we should prefer turbocharging in SI engine. What are the limitations of turbocharging in SI engine?
What, what will happen if I go with the high boosting? So this is like we are going to cover. So in my sessions, I give some hints in between, so maybe you can, uh, note it down important things which you feel. So now, uh, this is my model is ready. So now I need not to worry. So complete my architecture is ready. So that's the reason I tell your student that you always start with the example files. So, uh, whatever the engine configuration, we are, uh, going to model, we can get the, uh, close model from the example.
Or tutorial file. So that will be our reference model and then we can convert that into a, or we can modify as per the, our requirements. So now first thing, what I'm going to do is like, uh, we'll understand the complete model for us that how the air is traveling. So now if you see here, there's an environment at the inlet and similarly at outlets, it means what? It is taking from the environment, the air, fresh air, and then after burning, it is, again, is going back to the environment.
But now when in the exhaust, the difference is that it's not only air, but it is what we call is as a exhaust. And therefore this legislation norms, what it is telling, it is telling that we are moving towards the zero emission norms means what if you are taking the air from the ambient, you should give back air only. You should not give the pollutants with air and therefore the water, the pollutants, which are coming from the exhaust, let's say NOX or CO, hydrocarbons, particulate matters, particulate numbers.
So many things, if it is a CNG engine, then CH4, if it is diesel after treatment devices, then there is ammonia, NHT. So these are the pollutants, which comes out of the exhaust. So this norm says that the, this pollutant should be towards zero, it's not exactly zero, but let's say it should be 0.4 gram per kilo at hour or 0.01 gram per kilo. So there are some definite values and then we have to achieve those emission norms. So this is the environment. Then from environment, from the arrow, we can find out the direction of the air.
So it is like a, obviously this is inlet and this is outlet because if you see the arrows is going in this direction. So now the ambient air is coming and then it is going to the pipe from pipe. Then there is a plate. This is for Helmholtz resonator. We will not talk about that acoustic part. So then from inlet, it goes to the air box. This is air filter. The purpose of air filter is to filter out the dust particle that is coming with the air.
And then it filters out that so that in the combustion, we get a clean air. And once this is filter out, then it from the intake again, it goes to the intake manifold. So this is the intake manifold. So maybe this we will see during the discretization that how to convert a 3D CAD model of intake manifold into a one dimensional. So what with these models we call is a one dimensional. So as I mentioned earlier, one dimension is nothing but the properties are changing only along the one direction.
So along the procession, we are going to assume that the properties are constant. So now you can observe here something called the throttle. So before going into the manifold, there is something called a throttle. So if I just double click on that throttle, what I can see is that this throttle, there is something called a reference diameter and there is something called the throttle angle. So by default, this throttle angle is completely open. That is, it is 90 degree. So we have to very clear what, what is the convention zero degree means open or zero degree means close.
So now this zero degree, if you see that this is the angle versus the flow coefficient data for that particular throttle wall. And we can see that when the angle is zero, the flow coefficient is zero. It means when it is zero degree, flow coefficient is zero is nothing. But what we can conclude is that zero degree is fully closed condition and 90 degree is fully open condition. So now we know that in SI engine, how we control the power or torque is that we control the amount of air going to the engine.
And by controlling the amount of air to the engine, we can have the lambda control. And then we can have the fueling control. So in SI engine, there is something called lambda sensor. And that lambda sensor will try to always maintain lambda equal to one. So but at some point, as we have seen in earlier session, at some point, the lambda may go less than one that is a rich condition. Or it can go above one, a lean condition. So depending on the how we are calibrating our engine and how for what emission norms and what performance.
Also sometimes to reduce the exhaust and maintain the exhaust temperatures. What we do is we purposely send rich mixtures so that the combustion efficiency comes down. And then the reduction in the combustion efficiency will result in the reduced exhaust temperature. But obviously, when you are sending the very high or very rich mixture, definitely the amount of air is not available. And then CO and HC emissions will be on very higher side. But yeah, sometimes we have to use this strategies. Hear more of the During this changes.
Can you see all these changes? Thank you. It's like sometimes in high performance cars, let's say the racing cars or some of that, Lambda comes down to less than 14 point, that is size dramatically, because it is rich, so it can go up to less than 12, 5, 10, 9 also sometimes, so it's like a measure to control the temperatures and the performance. So now there is a throttle wall, which I can change the values, so if you go to throttle angle, what already they have done is they have defined this as a throttle angle as a parameter, so when we are defining this as a parameter, definitely we can change and we can for different cases, we can, so that's what we can see here, let's, if I go to the case setup, either I can go from here or I can directly just press F4, it will directly take me to the case setup.
So already they have generated 5 cases, so now one of the parameters, what we have seen is the throttle angle, so now you will see that everywhere the throttle angle is 90 degree, that indicates this is a full load point, so it means when the accelerator is 100%, these are these conditions, so throttle angle is 90 degree, second parameter they have used is the engine speed, so that at different, different engine speed, we can have less than 6000, 5000, 4000, this 5 speed, we can have, then there is an operation constant, ambient pressure, so major parameter is only speed and the throttle angle, so we will see that impact, so now then from throttle angle, if it is 90 degree means what, the complete air will be directly going to the manifold, so it will go to the manifold, so being as 4 cylinder, it will have the 4 runners, and then from, it will be distributed to the individual cylinder, so run a 1, 2, 3, 4, and then air will go into the, so now we have seen that this is a SOHC, that is a single overhead camshaft with a 16 wall, and this is a 4 cylinder, so when we say the 4 cylinders and 16 walls, it means 4 walls per cylinder, and there are 4 walls per cylinder, it means there is a 2 intake wall, and 2 exhaust wall, and therefore, what you can see is that, in this cylinder, we have this, from intake port, it goes to the intake port 1, and intake port 2, so this is like a 2 ports, then from 2 ports, it goes to the cylinder, and then in cylinder, there is a combustion, and then combustion, we have again 2 exhaust ports, exhaust port 1, and exhaust port 2, so now, so now, this is very important, this intake port distribution, and as I said earlier, the intake port, we don't consider any frictional losses, why, we ignore this, because already, this friction, we are considered in flow equipations, so this flow equipations, you will find in this wall cam connection, in this template, if you go to the flow equipations, we can see this, so when the intake wall is completely closed, obviously, the flow equipations will be 0, and as it opens, from 0 to its maximum lift, the flow equipations will change, and this now, the flow equipations is very important, because this flow equipations will decide how much air is going to the engine, so if I have the higher flow equipations, obviously, resistance to the flow will be minimum, and then I can get a better volumetric efficiency.
Part 2
So this is about intake wall and then it goes to the cylinder. Now if you go to the cylinder what we can see is there is initial state object and then it is overwrite by this value unit FA. So we will understand this what is this unit FA. Then there is something called a T1. Now as I said what you can see is this yellow color here. It means what we cannot edit this because there are multiple parts. If I want to change simultaneously I should go to the object and then I should do the changes. So now what we can see is that there is a T-wall, there is a wash new heat transfer model and this combustion object is SIPP. So if I want to do some changes here it will be reflected for all four parts. So now let's understand what wall temperature they have used. So if you go here they have used this engine cylinder T-wall which is very basic heat transfer.
model where we have to directly give the heat transfer model where we have to directly give the heat piston and cylinder temperature. So instead of Kelvin let's say if I want to see what is the degree centigrade I can do that and it just convert this from Kelvin to Celsius and then automatically it will convert that to a Celsius value. So now what we can see is that the heat temperature and piston temperature. So now what we can see is that the heat temperature and piston temperature what we are defined is a 300 degree centigrade and the cylinder temperature is 126 degree centigrade. So now this is very important because that depends whether my cooling system is water cooled or whether it is air cooled that will decide how much temperatures it will be operated. What are my breakman effective pressures.
So let's say if I am going at the first time I don't know what values I should put. So always like there is a help right. So in help they will give you the range what should be the range generally it's like it's not composite that we should use this temperatures because as per way engine design it may change but there are some guidelines that what heat temperatures what should be the material temperature. It should be in the range of 550 to 600 degree centigrade obviously right because if I'm in metal temperature if it goes above 350 or 4 400 degree centigrade definitely that material properties will change and then it may fail for the durability. So there are some thumb rules that okay what should be the maximum material temperature we should operate and then accordingly we can directly define that okay this in my engine my head temperature is let's say 575 now if we go back how much we are defined head temperature is 575 Kelvin piston is 575 Kelvin and cylinder is a 400 Kelvin. So this I have defined now if I want to see if I want to see if I want to see a cooling system performance okay so in that case I cannot directly define this temperature then in that case I have to estimate based on how much water flow how much the cooling flow what are the properties of cooling system how much convection conduction so that I need to do in detail. So in that case I cannot use this simple model and then I should use a detailed model engine cylinder T-volt detail or engine cylinder T-volt solution. This we will not see this we will not see so we will stick to the very simple model then again the heat transfer object is washning combustion object is SIVB where I have defined is 50% burn point and burn duration. Now you are here what you can see is that directly we have not defined any value let's say angle 50% burn point is not we have not defined it is 8 degree or 12 degree but instead of that what we have defined here here is some reference so what if I double click here is a THB 50 so I can create that template if I double click what we can see is that there is a RLT dependence X Y means what X Y so there is a X and for that particular X there is a Y so what is that X so we can define that so it is a function of engine speed so as my engine speed will change the value will change the value will change so what is the dependence object so this is a X value and what should be the Y value so if I go this again there is a reference and then I have provided this value so it means what at 1000 RPM it should be 12 degree at 2000 RPM 9.6 3000 7.1 5600 9.5 so now you may be wonder right why these values are changing to let's say this fraction from 12 to 9.6 7.1 7.4 9.1 again 9.5 so like these values will come from the experience or maybe the test data which is available with you from the test data you will find out what is the 50% burn point and directly we can put this but as a student we need not to bother about this as of now but I hope you understood that okay how we have defined the 50% burn point instead of defining so I can do here let's I can put let's say 8 value so this 8 will be constant and for all speed it will be using 8 only but I don't want to do that so what I can do is in value select already they have defined this THB 50 as a RLT dependence so I can select that and then THB 50 what they have done is X axis RPM and on Y axis they have defined the value so it's like a table so as I mentioned in earlier session this table or this RLT dependence instead of X we can have the X Y and Z also so let's see I want to put the 50% burn point function of engine speed as well as the amount of fuel let's say MF I can do that so I will add X Y and for that X and Y I can add the Z value similarly what they have done is they have done use that burn duration and again a function of X and Y so for that engine speed what is a burn duration so they have directly given this value so always if I start from scratch modeling then it becomes difficult what values I should put and then we don't understand why my results are not coming close to the expected values and then we'll end up in putting some values or we start manipulating the simulation so that's the reason always we should start with the example file and then slowly slowly we should move towards doing it on our own so now this is the SIPP model okay now if I go to this advance there's a operation object they have defined you know what is this operation object if I want to understand I can just go and click on the help file so we can get that value so what is the operation object is nothing but that defines the in cylinder operation so we can set this ignore also as of now but let it be if they have used this factor we will return that we will not change as of now so this is about the cylinder and again the exhaust wall and intake walls intake wall they have defined some camp timing angle it's a theta equal to 0 so lift they have to lift they have to lift they have to lift that is x versus 5 this is a from the camshaft or crankshaft we can understand this so it's like a cam angle and in the lift what we can see is that against cam angle they have defined the lift with respect to cam angle so this is a lift then flow coefficient it is again the value a function of lift L by D ratio what is the wall street diameter reference diameter is 34.5 okay so that point if not that where does the bringing charge � plastic centers or here it is so that there is so at go to now this engine component and engine cranking what we call and let's see how they have defined this item so this is a four stroke this is a speed base it means what the speed we are going to change and not the load so load will be the output in this case so rpm so even if I want to see what are the rpm is if I just put my mouse here this arrow here what we can see is this values so there are five cases and the first case is 6000 rpm second is at 5,000 so we can understand I know if I want to change the values I can just go come here and I can see parameter values and I can change this values so that I can do now there is a friction model or friction FMVP value what we can see here is that there are some constants they are use which is engine friction basic model and now I want to see what should be the values here so they have defined that what should be the values 0.3 0.5 bar is a range for this while do peak firing pressure factor 0.004 to 0.006 so depending on our application we can put this values so this is about a friction model there is a cylinder geometry now see what are the values here bore is 86 stroke is 86.7 connecting all is 175 compression ratio is 9.5 so now if you see our model what we need to design is this four cylinder with 73 mm bore and 89.4 mm as a stroke and this is a natural aspirated engine and in the speed they are defined is the 6600 rpm and 4006 so we are going to solve only 2k so let's start let's change this bore to 73 mm and the trace this bore to 76coat value So what we do is 89.4. So we will change that. And now what is the connecting rod length? So now connecting rod length. So if you refer any design book, IC engine book, we will get these ratios. What should be the connecting rod to the stroke ratio? So generally it is let's say in the range of 2. So what we can do simply is that we can consider the double of that. So we can just put 180 mm here.
Obviously this is not accurate, but this is close. So like if you want to get the connecting rod length, you can refer any design book and we can find out, we can calculate that. Now let's start with the compression ratio of 9.5. So I want, I can change it to 10 or so, or maybe 10.5. So let's change it to 10. So now if you go to the engine specifically, we will not get the compression ratio values and everything. We can guess, but obviously being your SI engine, petrol engine, national aspirated engine, compression ratio, we can have is close to 9.5, 10, not more than that.
And now if you remember, there was one slide, which was talking about the relation between the compression ratio and octane number. So that I was showing in the earlier session. So if you want, you can go back and you can just see that. So there is a limitation. What octane number we are using? So generally in the market available, obviously I have to design for that. Not like, let's say performance cars or something where they specifically designed for very high octane number. And therefore when they go to petrol pump, they have to buy that high octane number fuel only.
So obviously, but they can afford because that the cost of the vehicle is more than let's say one crore or something. And then obviously normal petrol, if you are in, let's say you are getting for 70, 75 or 80 rupees, there will be delta of 20 rupees. It's like additional per litre. It will be let's say 100 rupees per litre. But obviously, if you are rich enough, then only you are buying those performance cars and then you can afford this. But in that case, then my requirement is that I am designing the engine for octane number, let's 98. So then I can go with even a higher compression engine. Instead of 10, I can prefer 10.5.
But then in that case, if I use a lower octane number fuel, the chances that it will knock. So for the safety of the vehicle or let's say durability of the vehicle, we will have to always use high octane number. But generally, if I am designing for let's say common application, then I have to see that what is available fuel in the market. And accordingly, I have to restrict the compression ratio. So let's stick to the compression ratio of 10. Let's say TTC clearance, height is 1 mm. Pistol to crank offset is 0. Let it be the 0 mm. And now we will not touch any other parameter.
So this is about a cylindrical geometry. Now what is the firing order? So now we hear the firing order. Generally for 4 cylinder, it is 1, 3, 4. For 6 cylinder, it is 1, 5, 3, 6, 2, 4. So these are the sum thumb rule. It can be changed also. It can be 1 from 1, 3, 4. It can be 1, 4, 2, anything. So now let's say this is a 1, 3, 4, 2. And this is firing interval is first less than 0. So obviously, it is a number of cylinders are 4. So if I divide 720 degree by 4, what I will get is a 180 degree. Now why 720 degree? Because this is a 4 stroke engine.
And then to get a complete cycle, that is a cycle of suction, compression, expansion and exhaust, it takes 2 revolutions. So 1 revolution is 360 degree. So 2 revolutions are 720 degree. So if I divide 720 degree by number of cylinders, I will get a firing interval. So that is every 180 degree, one cylinder should fire. So 1, 3, 4, 2. The interval is 180 degree. Now this is RLT norms. So now in RLT norms, there is this we have to define. So let's say intake initial is a volumetric efficiency and there is a second manifold.
So this is generally useful when it is the engine is turbocharged. So that we will see in the turbocharged session. But let's say now this intake initial. So we can define this intake initial and then we can say, okay, what is ambient pressure and ambient temperature. So instead of putting the value, they have defined this as a parameter. So let's see if I want to change the ambient pressure or ambient temperature, I can do that very easily. But if you don't want, you can just put 1 bar and 298 Kelvin.
And then altitude and humidity, we have doing this at the sea level. So we have, there is no altitude. So now if you see here, there is something called a composition. So now this, they have used the air. So if I want to change, I can change, I can select anything if I want. So there are so many, there are so many templates available. We can do that. But generally for air, we can use this fluid mixture and then we can directly select the air only.
So now this is done. Everything is done. Now what needs to be changed? If you go back to a model, four cylinder, we have done 16 mole is done. Now this bowl is 73. Stroke is 89.4. Everything is done. Now if I calculate the swept volume, how I should calculate? Let's say diameter is 73. Stroke is 89.4. So what is the formula? It is like a pi by 4 D square into S. So pi by 4 D is 73. So 73 square into stroke is 89.4.
So if I calculate and multiply by number of cylinders, I will get the total swept volume close to 1.5 liter. Then we have to run for two cases. So how we can do that is we already have the case setup and RPM has been defined as a parameter. So what I can do is I can delete the other cases. I don't want to run that. So I will keep only two cases. And now the speed. So it's like RPM is 6600 and 4600. So we have done that.
Throttle angle we will keep 90 degree because it's a full load, full throttle performance what we call. When it is 90 degree means what there won't be any restriction to the incoming air. Whatever the air is coming from the air filter will directly go to the manifold. And therefore maximum air is going to the engine. And then from maximum air we can burn maximum fill maintaining the lambda. And then we can see that how much torque is generated. So these are the two cases. Now we have not defined a failing or anything.
But how we can do that now this is a gasoline direct injection. So instead of injecting in the port, we are injecting in the cylinder. So now this is a injector. If you go there, what again you can see this yellow mark means what we have this four parts. So more than one part are there. So it's like a four. So if I go here, what I can see is the injector delivery rate is 6.5. And then fuel ratio. So again fuel ratio we have not defined a single value here.
Or we have not defined. So we have defined one reference that is fuel air ratio. And again what we have defined is the dependence on the x5. So it's like a function of the speed. So we can consider that. So what is the value we need to ask you. Now see, it has given 0.08, 0.0085 or something. So it's like, what is this? Earlier session we put 14.5, 13, 16. But now here we are putting 0.08. Is there any mistake? So let's go back and see.
Yeah. So now here the fuel ratio specification. So what we have done is instead of air to fuel, we have defined the fuel to air. So fuel to air means what? So numerator will be fuel and air will be denominator. So it's like numerator will be smaller and denominator will be higher. So it will come less than 1 as against the air flow ratio. In that case, the amount of air will be a numerator and it can be fuel. But let's say if I want to change, I can change this.
Let's say air to fuel ratio. And then I can put those values. So how we can do it, I calculate is that this is air flow ratio. So reciprocal of that is nothing but air flow ratio. So let's put, we can calculate that. Let's say if we go to calculate and let's say 1 divided by 0.08. So instead of putting 0.08, I can put 12.5 here and then what I should do here is instead of fuel to air, I should select the air to permission. So you have to be very careful when we see such numbers.
So it's like a fuel to air ratio. So now if I just see, so what we can see is the fuel to air ratio is less than 1. It means it is rich mixture. So it's like 0.08, 0.08, everywhere this is a rich mixture. And that's the case because this is operating at full load. That is maximum air is going to the engine. And if we are putting the maximum fuel and then when we are putting maximum fuel, chances that the exhaust temperatures may go high, very high value, NOx formation will be very high.
And therefore to reduce that, what we can do is we can run it rich instead of running at lambda is equal to 1. So this is about the injector. So now what it will do, it will calculate amount of air going to the engine and accordingly it will access the amount of fuel to maintain that value of equivalence ratio. So that is called equivalence ratio. So it is like a reciprocal of lambda. So everything is done. Now let's run this, okay, without touching any other parameter.
So when I say the run, so that pre-processing is done. So local, simplicity, show runtime, monitors if it is there. Thank you. Okay. And now as we are selecting the parallel, it will not show the, so here is like, depends how many cores, now my machine has 8 cores, so I can select 7. So in parallel it can solve on 7 cores. So my brand will be on faster. But now let's see, the only two cases, I need not to be worried about whether it should be parallel or individual, we can do that.
You can go to the simulation options and I can say, okay, show graphical user interface. Now the solvable architecture is 64 bits and solvable is standard installation. We need not to worry about. So generally, 2018 onwards, we have only 64 bits, so we need not to worry. Okay. And just refinished. Before that, we can check how many cycles they have given is 40. So unnecessarily, it should not solve 40 so that we can check in the run setup. Setup. In run setup, we can just see, okay, whether the automatic shutoff when steady set is on. Yes. She's already on. So we need not to worry. So even you can put here 100 or 1000 also. Once it reaches the steady set, it will converge and then it will stop. So that convergence criteria also I can define, let's say, in flow control, how many cycles we want, let's say, sorry, not here, ODA control.
So we need not to worry. So we need not to worry. Now just run. And what I can do is in simulation options, sorry, I will deactivate this parallel case so that I can see the graphical user interface. And just say finish. Now here, before it's going to run it, checking all the settings, if anything is wrong, then it will directly report that okay, settings are wrong. So then it will not solve and directly it will even show also. So that was I will show. As our license is server based depending on the internet speed, it will take some time to initiate.
So just started. Now we can observe it at case number one, it is taking 10, 11 period point two seconds to solve. And now case number two, case number two is taking more time to solve. So what we can see here is that is not converge yet. No, no, no, no. So yeah, now this is a good thing. Now see what has happened. Case number one has converged very easily. But case number two, it has not converged yet. No. So it has reported a warning that one or more cases in this model did not reach steady state. So we can see here is that number case number two has not reached a steady state. So what we can do is that so it's like it's not accurate. It needs to converge further.
So what we can do is that. So what we can do is we will stop this. And then we will run again. But before that now number of cycles. So I can do from here. Sorry, I cannot do this. So I need let's I will put 100. So now what do you have to say if I change this 100 automatically it is changing this value here also. Okay, so I'm going to run this case now. Let's see. What are the results. So depending on the internet speed it will take some time because this is server based license. So now it will show the progress case to it is taking more time. We can see this mass flow variation is there but this is within 0.1 percent. Sorry 0.8.9 percent variation. So though it is showing that it did not match we can go ahead because this is with the gap is very less.
Now let's view the results. Now let's view the results. Now what was our target. Our target was to get this 87.7 kilowatt at this 6600 RPM and 145 Nm at 4600 RPM. Let's see how much we have achieved. So as we have run the two cases. So as we have run the two cases. We will directly go to the macros and we can see the combined table data. And then we can select both the cases and what we want to combine this engine and cylinder data combined.
Let's see okay. Get all the data. So this was the board was 473 mm stroke was 89.4. So what we can see here the total displacement of the engine is close to 1.497. Compression ratio we have given is a 10. And then we have given is a 10. And then we will not talk anything on the IBO EVs IBC EVO EVC. This we will talk later. So what was the RPM 6600 RPM and then 4600 RPM. And then what about the torque and so now let's see how much power we are getting.
We are getting 90.7 kilowatt at 6600 RPM. And at max torque condition the target was to get the 145. So we are very close. So now if I now find the delta between these two. It's like within 5-10%. So within a first run we got very good results. And then all other things we can see. Okay. What is the air flow rate we are getting. How much BSFC we are getting. What is the volumetric efficiency. See it's like everything is perfectly matching. We are getting 98.3% efficiencies at full load max power point and close to 98.4 at max torque condition. So everything has matched perfectly. The air flow ratio we wanted to keep is 11.7 to 11.91.
So we got everything correct. So it's like in a single run we got our results. So it's like thermodynamic simulation. We are assuming that everything is working fine. The friction losses everything are there as we have defined. The temperatures of everything. But in real life obviously this is not that simple. It's we don't design engine and everything within 10-15 minutes. Obviously this is like architecture. So now this what this indicates that this 1.5 liter engine is sufficient to give you the required power and the torque. Now I was talking something about the BMP. Now let's see what is the BMP level here.
So it will be reported here. So if I see the BMP level here is 11 bar and then at max torque point is 11.9. So now this will show you that okay it's though we have achieved the values but it is very difficult. So we have achieved that actual condition to get these values close to 11 and 11.9 only with the natural expected engine and its values. But yes thermodynamically we can say that it is possible. Now what is the maximum pressure we have achieved here is 62 bar close to 62 bar everywhere and in the this so 1, 2, 3, 4 cylinders it is reporting.
And in second case 1, 2, 3, 4. So what about the volumetric efficiencies we have seen. So we can see that there is some variation. So this happens between cylinder to cylinder because of the wave dynamics. So at cylinder 1 it was 97% cylinder to 100% cylinder 98.3 is 97. Again for case 2 it is 100 when 1% cylinder 1 97. So this is because of the wave dynamics. How much exhaust temperatures we have reached is 1139 Kelvin and this 1130 Kelvin. And then we have not activated any NOX model and CO model we can see.
But now see what are the CO levels very high right. This is because we are operating the engine at reach condition and in reach condition we are getting very high CO values. And feasibly if it is a practical it's not possible to go with this high values because if you go this high level obviously my after treatment device will be bigger. I will require more coating of palladium and platinum to reduce this or to do this oxidation. But obviously when we can reduce this CO level by further tuning by having this lambda control measures.
And it has been a total of 8 or to 100 minus 1 in the moment. So that's what is expected. This is the question of what we need to see. So that's why we can reduce the problem. And the space, we can reduce the pressure. And the power of this light we can reduce the pressure on thisak. Thank you.
Part 3
So this is how we got everything within the limit. Now let's see what is happening at the class level. Engine cylinder if I go and I will select the pressure values. We can see how much pressure is built. Lock PV diagram we can see. This pumping loop we can see. The temperature we can see. Heat transfer rate. So this is how the heat is transferred from gas to the cylinder. Well we can understand how what is the burn rate. This is very simple burn rate. So we are forcing that okay. This is how the combustion will be and this is how the heat will be released. It will be burned. That air fill mixture will burn in this with this rate. It's like this is a burn rate. So now this burn rate we can control by this parameter such as MP50 burn duration. If I change those parameters this burn rate profile will change and accordingly my performance switch. Again for SI engine the major challenge is the cycle to cycle to cycle ratio because cycle must have LeBron rate will change as a cycle ratio with進 into the cycle reached the chart in battery. Studyout time to decrease the actual size of the ketemi. You will add 2 times like this here at the end of that issues so you have to very careful while designing so theoretically if you say we will get it will run exactly the bond rate profile will be like this incident pressures will be like this but in reality that is not the case but yeah now this thermodynamic simulation will tell me okay if this is the pressures and temperatures how much performance i can derive out of this so now if you want you can play with these parameters and we can see the difference what will happen let's see if i change the vp parameters here or one duration we can change that and we can see how it will change so we can change this okay so let's go back to our presentation and let's understand other important things so we were talking about this it's a four cylinder this power so we got required power and torque it's very easy so we are seeing that what is important is air rather than fuel because if there is no air we cannot put the fuel so now let's understand this how this wall timings works so if i represent this tdc as the top dead center at this zero degree and bdc has a 180 degree so it's like there's a suction that's the first stroke so from piston will move from tdc to bdc and the crankshaft will move from zero degree to 180 degree and then again next is bdc to tdc the crankshaft will move from 180 degree to 360 degree that is the second stroke then again the third stroke is expansion stroke again 180 degrees so that it's like zero 180 360 and now 540 and now last is 720 so this is a fourth stroke so this is a very theoretical cycle that exactly at the tdc we are opening intake wall open during the suction and then at the bdc we are closing the intake wall so this is called a suction stroke okay and this is a ibo and ibc then from bdc to tdc that is called a compression and exactly wall will close at bdc and then there's a compression now then the compression and expansion stroke both walls are closed because when wall are closed then only there will be compression so in third second stroke the both walls are closed and then there's a compression and towards the end of compression there is a spark plug and then combustion happens that is the third stroke what we call and again the both walls are closed here there's expansion and exactly at the bdc exhaust wall opens and then the last stroke is a exhaust stroke so this is very theoretical cycle but in actual it is not like this because uh we cannot open uh and close the walls instantaneously it will require some time because of this camshaft curvature so this is how the camshaft is and then according to the firing order we will have the orientation of the camshaft and this is how the camshaft is this is the best circus it is not exactly circular it is something there is a cam profile and this now this cam profile will decide the opening and closing and this is what we put in the GT-POWER if you go back here and they say intake fall this is how we put right the timing so this is nothing but a camshaft profile and this camshaft profile will decide my intake fall opening and intake wall closing so we have to design a camshaft based on our requirement what should be the intake wall opening we want and what should be the intake wall close and as this is there is some profile for camshaft we cannot open intake wall or we cannot open close that intake wall instantaneously it will take some time and that is what we can see here the reality is not instantaneous but something like this so intake wall we open before tdc and then we close after bdc and then exhaust wall we open before bdc and close after tdc so this is a period that is called a wall where both the walls will be open and that is called a wall overlap and therefore people are moving towards the gdi case because if it is a port injection what happens is that that mixture may directly go to the exhaust so this is how the reality is the intake wall opens before tdc and intake wall closes after bdc so let's say if it is a tdc position how gt reports is that gt reports with respect to a zero degree tdc what we call the gas exchange tdc so if you see in the two cycles the tdc is uh we get two times and bdc we get two times so the one is called a gas exchange tdc where the intake wall and exhaust for both are open and the second is called combustion tdc where the both walls are closed and there is only combustion happens so so gas exchange tdc we have to tune very carefully because this intake wall if we open very early or if this exhaust wall we close very late chances that the intake will bypass to the exhaust similarly this ivc now this ivc closing ivc after bdc why we close after bdc because what happens when there is a intake air which is coming to the cylinder though the piston has moved to the bdc this we have learned in our engineering right why we close the intake wall after bdc what happens uh intake is still coming into the cylinder and because of the inertia even the piston has started moving from bdc towards tdc intake air is still coming we take advantage of that and what we do instead of closing at the bdc we delay the wall closure so that even though the bdc from piston has started moving from bdc to tdc air is still coming and then we close late now this closing is very important if we close very early we will lose some uh trap mass if we close very late chances that whatever the air has trapped inside the cylinder will go back to the intake port because wall has not so we have to be very careful with this ivc and therefore this ivc is a function of engine speed and that's what we will see that uh in some engine applications people call something called variable wall timings so instead of fixing because once i make the wall profile camshaft profile i cannot change that right on the engine while running so there are some mechanisms by which i can have the different different wall timings so there are companies like honda they have this iv take what they call it is bmw they call voltronic system some will call vvt some will call vt vt anything or different different names but all technologies are similar it's like a variable wall timings nowadays um people are uh instead of using the camshaft there is something called uh electronic uh wall and then directly by giving the electric signal we can open and close the wall instantaneously and then that will give me maybe because then we have the infinite possibilities of wall opening and closing the only problem with that technology is the cost and the durability factor but people are working hard on that area and maybe in your future we will see that camless engines that's there won't be any camshaft but directly a engine this electrically operated walls so similarly for exhaust flow wall closure and exhaust wall opening i can have some variability so that uh we will get benefit so one of the technology in the market uh we must have seen is this iv take what we call the honda iv take this like a dual wall timings so at one particular engine speed the wall timings are narrow and then once it is moveable let's say 3000 or 4000 rpm then the mechanism will operate and it will delay the wall closure so this is like ideal operation where diesel is integral opens and intake wall closes this is normal but let's say uh when the mechanism is on what it will do is it will delay the wall closing so we can see here so it has delete the wall close and therefore you What will happen at high engine speed, I will operate this camshaft profile and at low engine speed, I will operate this.
So the problem of backflow can be avoided and then we can take advantage of the engine, this inertia of the incoming air. This is called continuous variable volume because in previous it's only dual timings, only we can have only two timings, either this low speed or high speed. But let's say if I want to change continuously, okay, more variability I want. So this is some technology from Fiat is the multi-air technology, which is very popular in the market. And then here what we can, this is hydraulically operated cylinder.
If you want to see how it operates, you can just Google it or you can go to the YouTube and you can find multi-air videos and how it operates. Even for Ivy Tech, how it operates, always go and we can check. So now here, this is a full lift, right? This is a normal operation. But let's say by, as we have this hydraulic cylinder in between, we can have infinite variabilities in the void timing operating. So we can just open very late and instead of opening completely, we just open, let's say half and then close immediately.
Or here, let's say we open and then immediately we close. So there are different, different engine operations we can do this way. And then this will have the control on the amount of air going to the engine. So once I have the control over the air, definitely I can have the control over the torque and power output, right? Because if I have the air control, I can control the amount of fuel accordingly to adjust the lambda and then we can control the amount of torque or let's say even the, if I can control the air, we can control the amount of nitrogen going to the engine and accordingly we can control the NOX, we can control the COHC.
So many things we can do very easily and therefore, this Fiat Multi Air technology is very popular. So why we require the flexibility in wall damage? Because at high engine speed, we have the high inertia of the incoming air and then to compensate that we can delay the IVC. Similarly, we can have the flexibility in exhaust wall opening, IVO and EVC. Therefore, this is called a fully variable, fully flexible system and generally higher end cars, you will see this fully variable timings. So another important things in controlling the air, because if what is told earlier is that we can control the torque or power by controlling the amount of air.
So if I want more power, what I should do is I should increase the amount of air going to the engine. That's what like you will see that all the technologies revolves around this air. Technology is a variable wall timing, so let's say turbo charging or super charging. What we do there is that we are trying to send more amount of air to the cylinder and then once you send a more amount of air, we can burn more film. That's it's that simple. So this is the naturally aspirated engine where we have this air and then there's exhaust.
How much, let's say we can derive 100 kilowatt output. Now, if I want to increase the power output, what I should do is I should increase the amount of air going to the engine. How I can do that is that we can compress the air. But once we have to compress the air means what we need compressor. So what we can do is we can add just compressor here. And then we can, once we add the compressor, we can send now more air. So now we are sending the more air, we can burn more film.
But now the question is how this compressor will operate. So we require some energy to operate the compressor. So let's say if I, that this is nothing but force induction what we call. So now from 100 kilowatt, we can, we have achieved the 200 kilowatt. But what has happened? This is a mechanical driven compressor. So nowadays there is something called E-turbo. So compressor can be run using the motor. That motor to drive the motor, we can take the power from the battery. So this is generally E-turbo is preferred in case of hybrid engines, 48 volt hybrid engines, where we can, we have this electrical power.
There is a separate battery for that. And then we can use that to run that. So that is called the E-turbo. But let's say if there is no E-turbo option, then we can directly mechanically driven. So from the crankshaft, we can take the power. And that is called a mechanical driven compressor. Or that is simply called as a supercharged engine. But in supercharged engine, what happens? To run again, we take this. So net output is now 170 kilowatt. Now what if I can use turbine? And that will work on the exhaust kinetic energy.
And then we can run the compressor. So that's what we do with the turbocharged engine. To run the compressor, we use the turbine. And the turbine from the exhaust kinetic energy, we run the turbine. And therefore this exhaust kinetic energy, which is going as a vest, can be used. So now the net output here is a 200 kilowatt output. So what we can see here is that the natural aspirate engine was 100 kilowatt. Then supercharged engine, we got the net output as 175 because 25 kilowatt goes back to run the compressor.
But in case of turbocharged engine, the net output is 200 kilowatt because to run the compressor, we use the exhaust kinetic energy, which is going as a vest. So this we will see in the turbocharged and supercharged station that how to model using a GT-POWER. GT-POWER is one of the effective tool to decide what should be the turbocharger size we should select. That is called turbocharger matching. Now there is something called, I was repeatedly telling you about the intake port and let's say the flow coefficients, right?
So there are two general approaches for the port ship. One is called a tangential or directed port, which in, this is used in the gasoline engine and this is helical port. So you can see this helical, right? So when it enters the air, enters into the port, so this port is a part of a cylinder head. It revolves around its axis, but this, this is called a helix, helix angle. So that helix angle will give a rotation to the incoming air and that is called a swirl.
And you will see that this is a swirl and this is called a helical port and this is a directed port. Let's say tangential port, which is generally used in case of SI engine. In the CI engine, why we require a helical port is because of the mixing. But in case of SI engine, we don't require a helical port because already the air and fuel is mixed and then there is enough time for mixture. And therefore, it is homogenous base and in case of diesel engine, that mixture is called a heterogeneous.
So that difference we will see in the CI engine modeling. So what we can see here is that this is a swirl motion, which is created due to the helix angle or a helical port. And there is something called a tumble motion, which is created because of this directed port. So in case of SI engine, what is important is a tumble. Why tumble is important because when it enters into the cylinder, it should not directly go and hit the liner because what will happen? Air fill mixture will go and stick to the liner and that that is not recommended.
So therefore to avoid that, what we do is we give some perpendicular motion to the axis and then the air fill mixture will not go and hit the wall. So it's like a tumble that is called a tumble and then so they understand the difference. Now, why I am telling this because if you go back to the engine modeling in this intake wall in flow coefficients, we have to define this. And then this data we get it from a swirl test trick. And then you will see that there is something called swirl coefficient and tumble coefficients.
So these data also we get it from the swirl test trick or tumble test trick. So if we put these values, this will be helpful for predictive combustion. This non-predictive combustion will not have any impact on the of these parameters, even the swirl or the tumble parameters. Now, in this our case, we are using the non-predictive combustion. Therefore, the swirl and tumble coefficients will not be useful. And therefore, we can ignore that. But let's say if someone is interested in the performance and emission predictions very accurately, then a lot of efforts are required.
So we have to go to that level where we need some tumble data, swirl data and then it's very difficult to get that data. We have to test it. We can start with non-predictive combustion and then slowly we can move. So this is about the swirl and the tumble. It's very important that we can see the tumble. This is a cross-section we can see here. So this is called a reverse tumble. Then there is a swirl. If you see the top view, you will see that there is a rotation motion because of the helix angle.
The squish I will talk during the CI engine. Now, I was always talking about the self-ignition. So now what is the self-ignition? So in a simple terms, if the temperature of an air fill mixture is raised high enough, the mixture will self-ignite. And without the need of the spark plug or other external igniter. Then the temperature above which this offers is called a self-ignition temperature. As we have seen that this is desirable for diesel because in diesel engines we don't use spark plug and therefore we depend on the self-ignition.
But obviously this is not desirable in spark ignition engine because if self-ignition happens means that is leading to the knocking. And therefore when there is a spark plug, when that is activated, when then only combustion should start burning. And therefore this is not desirable in case of the spark ignition. Now if I plot the P theta for the SI engine, this is what we have seen, right? The P theta. So it will, this is called a combustion TDC and then the P theta will go on increasing after.
Then it will arise suddenly because this is a constant volume cycle, auto cycle. It goes to max impression. So this happens very instantaneously and then it comes down. And then before coming to the BDC, we open the exhaust valve. Now, why we open before BDC exhaust valve? Because if we don't open this exhaust valve before BDC, what will happen? There will be a lot of burn gases in the cylinder and then we need to expel this out during the exhaust stroke. And if you remember, only power stroke is the positive and all other strokes are negative. So now if you don't open exhaust valve before BDC, all the burn gases will remain there in the exhaust stroke and then exhaust stroke negative work will be on higher side and that will increase our pumping losses. So to reduce the pumping losses, what we do is that we open the exhaust valve before BDC. Obviously, this will have some loss in the expansion.
But if we open the exhaust valve before BDC like this here, what will happen? The in-cylinder pressures are very high and because once you open the exhaust valve, all of a sudden the exhaust gases will come out of the cylinder. And that is called a blow down pulse. And that blow down pulse will almost 50% of charge will be released during that time. And that is 50% we can release during the exhaust stroke. So that will reduce my pumping losses. If you open very early, we will lose the indicative work. And therefore, we have to balance that.
Before moving to the assignment number three, what we are going to do is, now we will have some changes in our model and then we will see what is happening. So what we are going to do now is, let's first go to the GD post. And then let's just go back and now see, this is what the intake one. Now if I want, I can define this IVC, IVO so that directly it will show. So from where I will get this value, I will get this value from the report tabers.
So if I go here, this is what the value is. So we can note it down. This IVO is let's say 304 degree. IVC is minus 104. Sorry, yeah, IVC is minus 104. IVO is 304. EVO is 131. And EVC is 384. So if I supply, it will directly show. So now if I just go back. So now if I just go back and in the plots, if I see, I want to see, I want to see this timings of intake wall closures, I can put there, IVC is minus 104, IVO is 304. EVC is 384. And EVO is 131.
So if I supply, it will directly show. So now we can see here is that. What is this IVO? So if I want to see in terms of 0, if I want to see what we can see is that. So this is TDC is called a gas exchange TDC. And this TDC is called a firing. Therefore you will see that there is something called TDCF. So TDCF is nothing but a firing TDC. So we can start with gas exchange TDC. So we can start with gas exchange TDC. Now what has happened before TDC, we open the intake wall. So we can see that this is the intake wall opening.
Alright. And then there is a TDC. Piston will move to the TDC and then it will start going down. But now this exhaust wall will close. Yeah, this is the duration in which both walls are open. Now there is a intake suction stroke. Intake wall has open. The intake air will come here. Piston will go to the BDC. But now still what? Intake wall is still open. Because we have not closed intake wall at BDC. Because we are doing the very late. So this is during the compression stroke. That is from when the piston has started moving from BDC to TDC. We are closing the intake wall.
And then only the pressure will start building. So we will see that once intake wall is closed. Because now there is no way that air will escape. Because both walls are closed. Because both walls are closed. And therefore it will start compressing. And this way if you see this is called a dynamic compression ratio. Static is again a TDC to BDC. But dynamic is like when the intake wall will close. So it will start increasing. Okay. And now if I consider here it will go and then it will burn.
Now from once it is burn. Now from once it is burn. Pressure will come down. And now before going to the BDC we are opening the exhaust wall. So this is how we can see. And again now the exhaust wall is open. Again now there is the exhaust stroke in last from BDC to TDC. And now exhaust wall is still open. But now when for the new cycle intake wall will start opening. And now exhaust wall will close at after TDC. So now this will repeat. Alright. So this is called one cycle.
So this cycle will repeat. So let us say if my engine speed is 1000 RPM. The number of cycles will be 1000 divided by 2. 500 cycles per minute. This is like a half the engine speed. Because to complete one cycle we require 2 revolutions. Is that simple. So now let us go to the intake wall now. And let us see what is the mass flow rate. For the intake wall. We can see that. Or if I want to see the combine. I can also see that. So this is for intake wall. So we can see that. And then again we can add this IBO IBC here.
Let us say IBC is minus 104. IBO is 304. So now if I put there. This is what we get. So now this intake wall has open at this point before TDC. And now what we can see inside. Intake wall. Now this fresh amount of air will come to the cylinder. Till intake wall is closed. Right. And similarly if I want to see for exhaust. I can do that. Now before going to this. What I can do is. I can go to the file. Options. And I can say that. A plot table will automatically create.
Okay. So now if I go to the home. And now if I exhaust wall. I can do that. So now I have this intake. And this is exhaust. This is 0. I want to say everything 0 here. And then if I plot EVC as 384. And EVO has 131. Okay. So now exhaust wall has open. The moment exhaust wall is open. The air is now going from the cylinder. And then this is called a blowdown pulse. It will come down. But now piston is still moving from BDC to TDC. Right.
And that will push the exhaust out of the cylinder. But now obviously 100% exhaust cannot go out. Because there is some clearance volume. And some 2-3% will always remain. And that we can see here. If you go to the report tables. Enqueous that values. So if you go here. Come here. You will see the burn residual mass fractions. You can see that 3-4% will always remain in the cylinder. Because of the clearance volume. Sometimes that is called intern nature also. So this is about the plots. Now let's see if I want to see.
What is happening at the complete engine. So I can do that. I will just. Instead of no map. I will select the RLT contour map. And now what we can see. Is the complete pressures and temperatures for the complete engine. So we can see here. Now it will open. And now see average pressure. We can see. It started with the 1 bar. And then the pressure reduced to 0.985. Because there is some losses which happen in the air filter. Right. Because the air filter. There will be some. Always some losses.
So it's close to 1.015 bar loss. That is one close to 150 millibar lost in the air filter. And then 0.985. From the throttle. It goes to the manifold. And then it goes to. From manifold. It goes to the runner. And then from runner. It will. If you see. I want to see what is happening in the cylinder. If I just click here. It will open on the plots. So directly it will open the pressure. Locked PV diagram. Pumping loop. Temperature. Everything it will open. So now as you remember. These plots. We need to activate.
Before running. So that we can see. All the required plots here. So if anything. Is missing. We have to go back. And then in the cylinder. We have to go to the cylinder. Template. And we have to activate those plots. The required plots. So let's say. If I want to activate PV diagram. So I can activate that. But now. I have to rerun the. My case. So it's like. Okay. If I want to see. With respect to case RLT. I can see that also. I can compare here.
I want to see the RLT control map. I can do now. The exhaust port. 1.33. So everywhere. So this is how it has shown. Okay. Similarly. I can see. Temperatures also. Average temperatures. I can put. lesser degree centigrade. And I can see. What are the temperatures. So it's like. A 25 degree centigrade. When it enter into the port. It became 54. And then from cylinder. Then it goes to 690. So like. Very high temperature. Right. In the exhaust. It goes up to 700. 730 degree centigrade.
In the exhaust. And now this is very important. Now if I say from reach to lean, then this exhaust temperatures will also increase and that we can see. So this is like average temperatures what we can see. Now just observe here what is happening. Here it is 25 and all of 34, it has go up to the 54, 60 degrees. Why it has happened? It is because this is part of a cylinder head, right? This port is a part of a cylinder head and then cylinder head is exposed to very high in cylinder pressures and temperatures.
And due to conduction, what happens? The temperature of the material goes very high and that is obviously when as the port is a part of a cylinder head, the gases, that is air which is going through the port will get some heat through convection and therefore it gets heated because of that heat. Similarly in the intake and the exhaust. So that's the reason you will see that the port temperature is on higher side. All of a sudden there is a heating because of this port. This is a part of the cylinder head.
Part 4
So now we can check different, different properties, just go there and we can do that very easily. So that's the advantage with the GTPower that once you solve, we can get everything. So let's see if I go back to NoMap, you will see this report tables. At the same time, it will report some run summary also. It will give that, okay, which solver it has used, how many parts are there, connections are there, how much time it has taken to converge. This, this also we can get.
These are the few things, maybe if you are interested, you can just go and check. Only it will give you the energy use and losses. So how much total engine energy, okay. But now this is only engine, so we need not worries. Obviously the 100% will be from the engine only. But let's say if it is a vehicle model, then we can understand how much vehicle is consumed, how much engine is going, so let's like, we can do that very easily. So this is about the engine and cylinder, let's see if I want to see heat transfer, I can do that cylinder heat transfer.
Now we will see that, okay, how much is through piston, how much through head, how much through cylinder, for cylinder number one, how much total heat has been passed through the piston, through head, through the cylinder, we can do that very easily. So energy balance what we call it. So this is about the GTPOS, now let's say what I want to do is I want to compare what has happened with the cylinder one and cylinder to the, what we call the pressure. So I can do that in the macros, there is something called the combined cases and combined data.
So combined cases means what there are multiple cases, let's now have two cases, and I want to see, I want to compare their p theta, so I can do that. I have to just select this and I have to see the combine this and I can do that one. So now here what we can see is cylinder one and cylinder two. So we can see the variations, it will likely report that red is RPM 6600 and 4600 for blue. So this is p theta. Similarly, let's say I want to do for some other plots, I can very easily, we can do that, we can go here, we can say combine cases, combine those cases, unless I want to see log pv diagram, I can do that.
So it will just come back. So this is like useful when we want to compare different, different cases. This will show me the differences between these two values, whichever we want, we are interested, we can do that. Then there is something called RLD plots. In RLD plots, what we can do is we can select the case RLD, we can select anything, X, Y, scatter, 2D, contour plot, let's say I want to see 2D contour plot. I can select that, I can select next and then I can select what should be the X.
Let's say on X axis, now this is only two speeds, so this will not give a very good plot, but yes, still we can do that. Let's say I want to select from the parameters, I can directly select, let's say X as a RPM and on while, let's say it is fueling. So we can do that in, I think engine, crank, train, let's say fuel power. And on Z axis, we want to see, let's say torque. So we can see this, let's say finish. That's what I said, right?
It will not show because it's only running at only two speeds and therefore it will not plot the graph. But yes, if I just go back and say RLD plots for case RLD, X, Y, square plot, we can do that. X, so we can select X, Y1, Y2, Y3, anything we want and then it will plot the graph. So let's say X, I select again RPM, Y1 is, let's say, it's a performance parameter, I want to say what is BNAP. Let's say Y2, I want to see BSFC.
Y3, I want to see, let's say, friction power and just say finish. So we can do that, right? So now only we're at 4,600 RPM and then 6,600. It's only two speeds. So actually this kind of graphs we can plot when we have more number of cases and then we can do. But let's say now readily we want to see those plots. So we can do that here also. Case RIT, we can go. And favorites, we can say, okay, I want to see BSFC. So we can do that.
Same thing. It's like I'm just showing you that different ways of plotting. It's not that only whatever the ATGT reporting we have to, we can plot B1. We can have the case sweep, histogram, we can do everything. Even instead of combined cases, we can combine data also. Let's say for the 6,600 RPM itself, I want to compare, let's say pressure. So now what it will do? It will show the same group. So in the pressure, so where there is a pressure, it will show everywhere the pressure values.
So let's say I want to combine these two pressures. Manifold pipe 1 and manifold pipe 2. For these two cases, all cases involved, I can do that. It's very simple. So it's like we have two options here in macros. Either we can combine cases or we can combine the data. That is pressure in the same group, temperature in the same group, air flow rate, mass flow rate, whatever it is. So as per the data type, it will combine all the data. Now let's go back here and let's say I want to change the wall timings.
How I can do that? So these are the intake wall timings. There is something called a cam timing angle. So this is 225. So what it is showing? And then there is something called a theta equal to 0. So if I see my plot, how I have given the plot is my angle starts at minus 73 and it goes up to 83 and then there is something called a 0 angle, right? 0. So 0 is 10 point. So now if I see this is 0, okay, this is a TDC.
So always this, the theta we have to calculate is from TDC firing angle. So 0. And now theta equal to 0. So when theta equal to 0 is at max wall lift, right? This is what we can see. This 0 is at 10.2. So when the lift is maximum 10.2, this is 0 angle. So we have to calculate that, okay, what is the distance between these two? So we can easily calculate that. So it's always 180. This is 180, 360. And then we can add this distance.
But now we have to be very careful. What we have selected is cam angle. So either we can give in terms of cam angle or we can give in terms of crank angle. So sometimes people do this mistake. They select here cam angle, but they give the crank angle. So if I do that, then that will be wrong. So now this 2 to 5. Now this is really good with the GT is that it will directly show. So even by seeing also we can get the feel, okay, my theta is correct or not.
Let's say now if I put here, let's say some, let's say some number 300. And what we will see here? So I can see is that, okay, something is wrong because my intake is not opening before TTC. It is opening somewhere in the intake, somewhere in the system. So this is wrong. And intake wall closer is also not happening. It is happening during the compression curve. So I can just go back and say, okay, my calculations are wrong. So let's say 2 to 5. Okay. So now this is 2 to 5 is there.
So theta is there. So if I want to change, what I can do is I can just change this value by plus minus 2, 3 degree. This is 5 degree. So I can put in this 2, 3, 0 degree. So 5 degree, it will move by 5 degree. And then according to my IB, so this complete profile, it will shift by 5 degree. Okay. Now, I was talking about this IB take, right? In IB take, what has happened? If we just go back here, right? You see that intake wall opening is fixed, but only IB see it change.
So we are not touched the IBO. I have changed only the IB see. So now in this case, how to do this? Because if I do this way, what it is doing? It is completely changing my profile. It is completely shifting. Only it is shifting. This theta, if I change this value, only it is changing this value. And it is completely profile. So IB and IB see both will change simultaneously. I don't want to do that. So how I can do this is, so instead of theta equal to 0, there are some other parameters.
So that is called opening RLT and closing RLT. So if I just select the opening RLT, what it will do? What does that mean? So we have these different different options. So theta equal to 0, array start, array end, max lift, opening RLT and closing RLT. So opening RLT means what? Opening RLT indicates that angle array will be referenced to the angle at which the wall actually first sold. Taking into account wall lash and leaf multipliers. This reference angle is reported as a RLT variable name wall opening timing angle at input referent.
So what you are doing is the opening RLT reference. Instead of theta equal to 0 now it will consider this opening RLT. But problem with opening RLT once I select this opening RLT it will not show me the graph. So then it becomes difficult to judge. So what I have to do is now this is cam timing angle. Earlier it was theta equal to, for theta equal to 0 it was 225. Now once I do this opening RLT I will have to recalculate that. So in next session I will show you how to do this calculations for opening RLT and closing RLT.
So this I will be doing in compression ignition engine sessions. These two sessions again we have some compression ignition techniques and then again a case study on this compression ignition. That I will be taking for heavy duty. So now what I am doing is like we can just stop here for SI engine. What I assume that after our session you will again try you will repeat this. I will recommend that you start the similar way. And then you can take you can just go to the internet any SI engine we can start with.
Don't just take very higher end or like which has a turbocharger or let's say it has a hybrid or something like that. Just take conventional SI engine, national aspirated engine and try to get the maximum data and then try to put all the data. So now here as I said I am not looking after the accuracy that how much accurately we are getting the results. That's not important here. And then once that is done then we have this assignment number. There I have mentioned what are the things we can do.
So now here this is about the gasoline engine. Let's now there is one more I was showing right in examples. So in gasoline we have a lot of things we can explore one by one. But in natural gas also we have something. So let's open this natural gas example and just see how it is different. This combustion and everything. So now this being a SI engine now this is six cylinder turbo charge engine. This turbo charger we have separate session. I will not go into detail.
But let's say now cylinder. What it has done? Everything is same only the combustion object. What we can say is again the same VBO model only. So what is the change? How it will understand that this is not petrol engine or gasoline engine but this is a CNG engine. Any cases we can have currently. How it will understand that this is not a petrol engine. So obviously we have to change the fuel type right. So now where the fuel we are mentioning correct. We have here the enter compression engine.
So this is a fueling. So where now we can see. So now here obviously the fuel ratio specific is air to fuel. Then air fuel ratio we have defined as a parameter. And in air flow ratio we have defined here is 41. What is the CNG? It is a stoichiometric air flow ratio. So CNG stoichiometric air flow ratio is 17.5. And then this is a fluid object. So now instead of the. If you go back and just see. What was the fluid object when we were doing the gasoline engine.
And now this is a natural gas. So now in natural gas. That is like. We have to. We can define this. Methane vapor. Ethane vapor. Propane vapor. And in methane vapor. This is a standard fluid gas. So we cannot change this. Okay. So we can see. This object is linked to this library. And then attribute with this background cannot be changed. Cannot be modified. But if you want to change this. We can do that by. Delinking from the library. If you want. We can do that.
So this is methane. Ethane and propane. So this proportion. The 88% is methane. 6% is ethane. And 6% is propane. So we can. On the mass basis. We can define this. Or any fuel. It is not that natural gas. We can define anything. It is only. Methanol. Ethanol. Let's say LPG. Or let's say. LNG. Biodesail. We can define any. Fuel here. So this is how this. It will understand. Now GT will understand. The. It has changed. Fuel type. It is from. Gasoline to now. It is a.
CNG. So it will solve for. CNG. Now in GT. The. Some tools available. So if you have. You can directly open. From here. This file. So if I go to the. Resources. What I can find. Is that. There is some. Utilities. Provided by GT. This is called. Calculative. Fluid properties. I can get. One exercise. Where I can. Find out. The. Stratometric air. Fuel ratio. For any fluid. You have to just type. Hydrocarbon. Ratios. And then it will calculate. So that you can explore. Later. So it's like.
For. SI engine. Everything will remain. Same. It's not different. Only thing is that. Only fluid properties. We need to change. And accordingly. There are some. Parameters. Which may be. Some temperatures. Or let's say. Some air fluid. Now let's see. If it is a CNG. Engine. What we can see. Here is that. This compression ratio. Is like. 13. Because if you remember. The CNG. Has the highest. Octane number. Up to 120. And therefore. We can operate at. High compression ratio. So therefore. We will see that. The compression ratio.
Here is a. The rest of the things. Remain. Same. So it's like. Once you have. This SI engine. Modeling exposure. Then we can. Model any. Fuel. Which works on the SI. Now only difference. Is that. Whatever the combustion. Model. We are using. Is non-predictive. But let's see. If I want to use. The predictive combustion. Models. And obviously. You require. To have. A lot of efforts. To tune. The combustion. Chemistry. Model. Because then. It has to. Estimate. That what will happen. If that particular. Fuel is in.
Is there. In the combustion. And what. How it should. Burn. And then. Which species. Will be developed. So it's like. Generally. No one. Does this. Using Monday. For that. We. Can estimate. This emissions. And everything. Very easily. But let's see. If you have. The taste rate. Available. Then I can. Tune my. Performance. Combustion parameters. And then I can. Make a. Predictive. Combustion. Model. Out of that. That is also. Possible. So now. Let's. What do you. You will be doing. This. This. After this session. The assignment.
Number. What I'm. Giving you. Is. Very simple. So what I'm. Telling. Is that. Select. Any. Engine. Model. Get. Engine. Specifications. Assume. Suitable. Data. Where. Possible. And run. For at least. Max. Power. And max. To condition. And just see. Where you are. Like. Whether you are. Getting the. Feasible. Results. Or not. I don't want. A manipulation. I'm not. Going to take that. Okay. How much accuracy level. But it's like. You explore. Wherever you find that. Okay. I'm not getting. We are there to help you. You can ask the questions.
I'm there to help you. Always. You can go to the internet. You can find a relevant data. Or like. Sometimes what happens. Internet you go. Won't get. Authentic data. So it's like. Books. You can refer. As I mentioned. Earlier. You can refer. Any ice engine book. And then get some data. Out of that. And once you've done this. Then compare the results. And list on important. Parameters. You can find out. Whether my. PSFC levels. Are in the range. The main cylinder pressures. Are in the range.
Is not that only power. And torque. We should see. We should see. All the other parameters. So like. Exhaust temperatures. Are feasible. Or not. In cylinder pressures. Exhaust temperatures. Then. If I want to see. If I want to see. We can activate. Some NOX models. CO model. And we will see. What is happening. With the. What is the. PPM level. Whether my compression. Visual inputs. And everything. Accordingly. I'm getting the. In cylinder pressures. Or not. So these. Basically. You can. And then. Once this is done.
And then you can. Post process. And take snapshots. For following data. Let's say. PV. Lock PV diagram. These are very few. I have listed. It's not that. You should do. Only this thing. If you want. You can. Add more. Relevant. Graphs also. No issues with that. Leggings in the. Pressures and moderate. So that's it. For today's session. So it was about. The SI engine. Case study. It's like. Not only. We are not only. Focusing on. The GUI. Of the GT bar. But simultaneously. I'm giving you.
Some. Like. Thumb rules. And how. Which parameter. We should see. Which range. We should expect. Something like that. So I hope. You'll solve. This assignment. Number three. And then. We will meet. Next week. With our next topic. On. CI engine. Modeling. Technics. Like. Compression. Ignition. If possible. You can. Have some. Before this. On. Compression. Ignition. So that. You will. What I am. Till that. Bye. Bye. And. Thank you. Attending. My session. Thank you. Bye. That's why. wing.