← Previous lessonFree lesson 2 of 3 · lesson 2 of 12Next lesson →

Unlock all 12 lessons of IC Engine Calibration using GT-POWER and GT-SUITEFull course ₹40,000 · paid

Price & syllabus
Free lesson · 103 min · no payment

SI Engine Basics and Single-Cylinder SI Model in GT-POWER

A free lesson from Skill-Lync's IC Engine Calibration using GT-POWER and GT-SUITE course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “2.0 - SI Engine Modelling Techniques - Part 1”

What will you learn in this free IC Engine Calibration using GT-POWER and GT-SUITE lesson?

The instructor reviews spark ignition engine fundamentals, including components, port and direct injection, octane number, knocking, compression ratio and BSFC. The model walkthrough then covers the injector, lambda, cylinder initial state, wall temperatures, the SI Wiebe combustion model, friction, firing order and intake valve flow coefficients.

  • SI engine knocking, octane and compression ratio limits
  • Meaning of BSFC and air fuel ratio lambda
  • Cylinder setup: initial state, wall temperature and geometry
  • SI Wiebe combustion inputs and firing order

What comes after lesson 2?

The next free lesson is lesson 3, “SI Engine Case Study: Four-Cylinder Model Setup from an Example File” (103 min). Later in Skill-Lync's IC Engine Calibration using GT-POWER and GT-SUITE course (paid): lesson 4, CI Engine Modelling Techniques - Part 1; lesson 5, Case study on CI engine - Part 1; lesson 6, Turbo Charge Modelling - Part 1. The full course has 12 lessons (18 h 43 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Part 1

Hello everyone. Welcome to our session number two under the course IC Engine Modeling using GT-POWER, a 1D system simulation tool. I'm Siddharth and our today's topic is SI Engine Modeling techniques. Before going to our next session, hope everyone has solved assignment number one. The purpose of assignment number one was to get you acquainted with the GT-POWER tool. Where are the basic settings, Indran setup, output setup, plot setup? Hope everyone has solved it. So now let's go ahead with the SI Engine Modeling techniques. So when I say the SI Engine, SI Engine is nothing but a spark ignition engine. Why they are called spark ignition engine? Is because a spark plug is used to initiate the combustion. So there is a basic difference between SI and CI Engine. So CI Engine is a compression ignition best where there is no spark plug and there is a self ignition in the combustion. So let's focus on SI Engine Modeling techniques. So when I say the engine components, which are the basic components, which are the basic components, there is a cylinder head. So what we call general is a 5C. That is C stands for cylinder head, cylinder block, camshaft, crankshaft, and connecting rod.

The other important components. The other important components of engines are piston, fuel injection system, lubrication system, cooling system, air induction system, radiating. So there are so many. So out of that critical is turbocharger. So every each and every part is component is critical. So now it is very necessary. So now it is very necessary. So now it is very necessary. When we do the engine modeling, we need to capture all those components correctly. So depending on the fidelity level, we have to decide whether we are doing only a thermodynamic study or whether I want to include lubrication system, cooling system in detail, whether I should have the water pump in my modeling or fuel injection system.

So that depends. So that depends what is the purpose. Let's say if I am a water pump manufacturer, then I am interested in a water pump. So how it performs, whether I am getting the required head or not. So in that case, let's say a water pump is a part of a cooling system. So I need to model a cooling system proper in detail. Unlike in thermodynamic model, we assume that we will be getting the required cooling. So we can directly impose the temperatures of material and then we assume that the temperatures will be maintained.

So let's say if my focus is on the cooling system. So in that case, I will be using GT cool. So then in that I will have the detailed modeling of the complete cooling system. Similarly, let's say if I am interested in the fuel injection system, whether I am getting the required pressures or not, whether how my injection profiles will be in let's say common rail. So in that case, my focus will be on the fuel injection system. And then I will use a GT cool system to model all those things.

Similarly, let's say if my focus is on the dynamic side. So in that case, I will be using, let's say if it's a wall train system. So in when I do the thermodynamic simulation, what I assume that I will be getting the cam profile and I will be getting the required wall timings. So there won't be any bounds or there won't be any dynamic issues. So wall will exactly open at the defined timings. So this is what my assumption, but let's see if I want to understand whether I'll be getting the required wall timings or not.

So in that case, I'll be using a GT wall train. So if you remember in our session one, I explained that there are different, different models. Let's say GT-POWER, GT MP. So that GT-POWER MP comes under that. So in GT suite, we have GT-POWER, which is basically used for engine and after treatment system, let's say, or maybe a real time system. And there are other components as well. Let's say GT wall train, which will take care of the wall train system. GT cool, which will take care of the cooling system, lubrication system, or where there is a fluid I want to do in detail modeling.

Or let's say there's a GT drive, which takes care of the transmission part. So there are different, different tools according to the application. So now we, our focus is on the GT-POWER. So let's see this engine. So now any engine, we will have the different components as I explained earlier. So there's a cylinder head, there's this wall train system, there's a block, there's a connecting rod. So there is a crankshaft, piston, this is a wall train system. Now this is an intake port, intake wall and exhaust wall, and then there's a port system.

So now I need to model this when I need to use the different, different templates. So this we have seen that there are different, different templates readily available. And according to our application, we can directly select the required template. And then from template, we can create object. And then from object, we can have the different, different parts. So parts has the properties derived from the objects that we have seen. So now when I talk about the SI engine, so there is no point in talking about the carburation system because that's outdated.

And the main reason for out that carburation system is out is because of this emission norms. So current Indian market, we have this BS4 everywhere, Bharat stage four. And now upcoming emission norms in April 2020 are BS6, Bharat stage six. We are moving towards a zero emission norms. And when we are moving towards the zero emission norms, we need to improve the technology. The carburetor system cannot be used. So this is outdated. And nowadays, almost all engines, gasoline engines are with multiport injection or nowadays it is moving towards the GDI.

So what is GDI? It's like gasoline direct injection. So similar to a diesel engine or a compression ignition engine, instead of injecting a fuel in the port or in the manifold, we are now directly injecting in the cylinder. And therefore this is called a gasoline direct injection. Now why it is becoming popular and almost all passenger cars nowadays is having this GDI. So there is a main advantage with GDI system is that in GDI system, there are no scavenging losses. So we are injecting the fuel after the intake wall is closed. And therefore whatever the fuel getting vested during the scavenging, we can avoid that.

Or what we call in the, in case of four stroke engine, what we call as a wall overlap, where both the walls are open simultaneously for a few degree. And then there are chances that the intake air will directly go to the exhaust. And now if we intake, there is a gasoline or that fuel, which is coming with the intake, then that intake, the fuel intake and air can directly bypass and directly go to the exhaust. And that is the problem with the, and now when I talk about zero emission norms, even a small amount of fuel is directly coming into exhaust is nothing but a carbon monoxide and hydrocarbons.

Basically hydrocarbons, if it is unbunded fuel and if hydrocarbons are coming in the exhaust, our emissions will be on higher side and then we cannot comply to the different, different emission. Now always there is a one misunderstanding with GDI is that people feel that for SI engine, if it is GDI, there is no spark plug, but yes, even if it is GDI, we required a spark plug. Because spark plug, that's what we call as SI engine. It's a spark ignition engine. We cannot initiate a combustion in gasoline engine without spark plug.

Now if you, I don't know whether you are aware of this something called a GCI that is called gasoline compression ignition engine. So people are working and there are some successful stories as well, where people or engineers have developed a gasoline compression ignition engine. So a gasoline fuel working on a compression engine, but that is something different. So we'll not talking about, we are focusing on the conventional SI engine. So don't get confused. So this is how the combustion system in SI engine, GDI engine. So there will be injector and there will be a spark plug.

Maybe here it is more clear. So what we can see here is a spark plug and then here it is a injector. So GDI engine has both injector similar to a diesel engine. But in addition to that, we have a spark plug to initiate the combustion. So this is how the spark plug. So, so there is a gap between a positive and a ground. And then as because of the very high voltage and because of this gap, it generates a spark. So now when I'm doing the thermodynamic simulation, I need not to worry about whether my spark will be developed or not.

I have to directly tell the model that there is a spark at this timing. So it will directly start burning the fuel. Now, if let's say if I'm a spark plug manufacturer, then I may be interested whether there will be spark and what will be the intensity of the spark. In that case, then my focus will be on the spark plug. So there's a different way of modeling spark plug. Now, generally what happens as I said earlier, this simulation softwares are not artificial intelligent. It means what?

Whatever the input we are putting, it will calculate and give you the output. It will not tell you that, okay, your inputs are correct or wrong. So what is the main factor which we should take care while modeling the SI engine? So SI engine are prone to knocking. So SI engine are prone to knocking. So, what do you mean by knocking? So, knocking is nothing but abnormal combustion. So, the combustion is not normal. So, what happens during the start towards the end of the combustion, what happens? There is a knocking and then in cylinder pressures, fluctuation happens and that leads to the damage to the piston or component. So, always we have to see that knocking should be avoided.

So, which are the factors which leads to the knocking? So, it's like high in cylinder pressures and temperatures, then high compression ratios, high boosting and low octane number. Now, why I am focusing on this? Because, see, it's very important that whatever the simulation or whatever the analysis we are doing should be feasible and it should not be only numbers. People, sometimes they do some analysis and then they generate some output and which is irrelevant. So, let's say now if let's say in SI engine, if I put compression ratio of 15, if I run my simulation, I will get very good BSFCs.

But whether it is practical, no, I cannot operate my SI engine at this high compression ratio. I should have compression ratio limited to 11 or 12. Now, there is some engines which has work up to compression ratio 14 being a SI engine, but then they are different. Example is from Mazda, that is the sky active. They have this SI engine with compression ratio of 14. But in that case, you have to take care of so many other parameters. So, you have to avoid a knocking. So, when it is not possible to operate at 15. Simulation will run. Simulation will run at compression ratio 15 and it will show that, okay, it is BSFC brake specific fuel consumption is very good.

Now, what is BSFC? BSFC is nothing but to generate one kilowatt of power, how much fuel is consumed. So, obviously, the BSFC should be on lower side. It means what, let's say if there are two engines, engine A with the two, let's say 300 gram per kilowatt hour. And engine B is with 305 gram per kilowatt hour. It means, obviously, my engine A is very good because it is consuming 300 gram per hour to generate one kilowatt. Instead of if you compare to engine B, which is taking 305, so it is taking 5 gram more. So, obviously, my engine A will have the better fuelization.

So, now it is very important to understand before we go to the SI engine modeling. We have to be very careful when we give the inputs. We have to ensure that what are the inputs we are putting are relevant and what are the outputs we are getting is also a feasible output. We should not get we are not interested only in numbers. So, that's the reason I'm focusing on some fundamentals, which we should take care. So, here, always there is a confusion with students. So, what is octane number? So, now, if I ask the students what is the octane number of petrol, they will say 90, 100. And if I ask what is the octane number of diesel, they will say no sir.

There is an octane number to diesel. There is a sit-in number to diesel. So, this is partially correct because octane and sit-in they are just numbers. So, we can find the octane and sit-in number for any fuel. So, if you see the table. So, if you see the table. Now, here, what I have listed is octane number and sit-in number for different different fuels. Now, from the chart what we can see. Gasoline has very high octane numbers. So, in octane number basically there are two. One is called research octane number and motor octane number. I will not go to the basics of this but let's. So, generally, we have this two octane numbers and generally what we can consider is that the average of these two is octane number.

Let's say methanol. Highest 106, ethanol 107, LPG 112 and CNG has the highest octane number. And now, if I see the octane number of diesel, it is showing minus 25. Now, similarly, you go to the sit-in number. What is the sit-in number of gasoline? It is 0 to 5. Diesel, it is on higher side. But other than diesel, all other fuels has very low sit-in number. And other than diesel, all other fuels has very high octane number. So, now seeing from this octane and sit-in number, we can easily conclude that if the octane number is on higher side, I have to use spark ignition principle. And if the sit-in number is on higher side, I should use the compression ignition principle. And that's the reason you will find that all gasoline, machinol, ethanol, ethanol, CNG, LPG, they are SI-based and diesel are CI-based. Now, what is the reason behind that? Why we required a spark plug in case of high octane number?

And why we don't require a spark plug for high sit-in number? The figure towards the left, what we can see here is that. So, there is octane with high octane number. So, this is a very high octane number and sit-in. This is towards down. It is increasing. Okay. So, high octane number means what? A slow burning. And high sit-in number means what? Fast burning. So, when a fuel has very high octane number, it means what? That fuel will burn slowly. Correct? And that fuel which burns slowly is very good to work with the SI principle. Because in SI principle, what we do is we initiate the spark. And now, when we initiate the spark, the in-cylinder mixture should be consumed by a flame which is generated by the spark.

And when there is a spark. And when there is a spark is developed near the spark plug and in that flame is generated and that flame travels towards the cylinder. So, when it travels towards the cylinder, in that case, it burns that mixture. Now, imagine if it is a fast burning fuel, what will happen? When there is a spark plug, the flame will generate it. It will start consuming the mixture. At the same time, being this is a fast burning, there are chances that from the other point also, So, the flame will be generated. And then, there are chances of knocking. And therefore, I require a slow burning fuel in case of a SI engine. If let's say, in case of a sit-in, when there is high sit-in number, I have to burn fuel very fast.

Because there is a self ignition. Because there is a self ignition. And when there is a self ignition, we have to ensure that it happens at all other points in a cylinder. And that is the basic difference between octane and sit-in. I am sure you must have learned this during your engineering, this IC engine course. But, I thought before we go to the GT-POWER actual modeling, we should have some refreshment to this basic SI engine properties. So, we have to make sure that SI engine, we have to understand the basic difference between SI and C.

Because I have seen some students who mix the things. That is, they work SI engine on very high compression ratio. And then, they get very good results. But, they are not aware that this high compression ratio will lead to the knocking in real field. And therefore, this is not possible. Now, this SI engine works on auto cycle. This we have studied right. So, if I plot the PV in cylinder pressure versus volume diagram. What I can get is something like this. This work area. So, if I see this is let's say TDC position. And this is a BDC position. So, there is a suction from TDC to BDC.

So, air comes, air plus fuel mixture comes inside. And from BDC to TDC, there is a compression. Then there is a combustion. So, if you see theoretically, the combustion happens instantaneously. That is at constant volume. So, this is a theoretical cycle. And then from 3 to 4, there is an expansion. And then from 4 to 1, this is called a blow down pulse. That is point number 4. Exhaust wall opens. And all of sudden, the energy is released to the exhaust. And therefore, what we call this as a blow down pulse.

And then from 1 to 6, there is a exhaust. So, these are the 4 strokes. And now, if I see this is a clockwise. And clockwise means what? This is positive. If a PV diagram, if it is a clockwise, it means it is a positive work. And if it is a counterclockwise, which happens with the compressor, then nothing but a negative work means what? We have to provide the work for the compressor, but engine, it generates a work done. So, that is if I consider the area under this PV diagram is called a indicated work. This we have learned.

So, if I consider this area under the curve. So, if I consider this area under the curve or if I integrate this PV, what I get is a indicated work. Now, indicated work, if I subtract the mechanical friction and all other part of the friction, let's say pumping losses, what I get is a brake power or what we call the brake work. So, if I take the ratio of the brake work to the indicated work is nothing but a mechanical efficiency. So, this we have same.

Now, this efficiency of this auto cycle, if I plot versus a compression ratio, what we can see is the add. If the compression ratio increases, the thermal efficiency increases. Obviously, see this PV diagram, right? So if I want to increase the indicated work, what I can do is I can increase the compression ratio or nothing but this distance TDC to BDC. If I increase the distance, obviously the work will increase and as work will increase, I can get more work and I can convert this more work into a thermal efficiency.

So this is what you may be aware of that the thermal efficiency is proportional to the compression ratio or it increases as the compression ratio increases. So theoretically, if I want the best thermal efficiency, what I should do is I should just increase the compression ratio, correct? So that I can get a more, more, more, more thermal efficiency. But practically, this is not possible with SI engine because of the knocking limitation. So that we have seen in previous slide that when you go for the high compression ratio, there are chances that other than the flame, there will be combustion from the other end and then two flames will travel opposite to each other and that will lead to the knocking.

And therefore, you will see that maximum cases, you must know that diesel engines or diesel vehicle, passenger diesel vehicles or let's say passenger gasoline. You see that the diesel cars, they give you more fuel efficiency. Why? Because this is the basic difference. SI engines works up to 10, 11 and for diesel engine, they go up to 18, 19. So obviously, when there's 18 and 19 compression ratio, the thermal efficiency will be more. And therefore, in case of diesel engine, the thermal efficiency will be more. And therefore, in case of diesel engine, the thermal efficiency will be more. And when the thermal efficiencies are more, obviously, you require less fuel to generate 1 kWh.

So if I compare in terms of BSFC, the SI engines and CI engine, the CI engine common rail injections have the BSFC values of 200, 210 as against SI engine where the BSFCs are in the range of 300. So it's like more fuel, it is burning to generate 1 kWh. Therefore, you see that all bigger vehicles such as tracks, buses, they prefer diesel over gas. What we can see that the octane number and the compression rate. So if I want to operate at high compression ratio, I have to ensure that it has the good sustainability to the high compression ratio.

This we can find out with the help of octane number. So when there is a high, let's say now if the octane number of fuel is 90, it means what maximum compression ratio I can operate is 9. If I can use 100, maximum compression ratio I can design is 10. So this is a dependency on octane number. Now this is a photo of knocking in SI engine. So we can see what has happened to the piston. So there is a permanent damage.

Part 2

Now let's go to now GTPower and start modeling. So I'll open GTPower. So what we will see now is we will open this tutorial and then I will show you how they have modeled the SI engine and in which combustion model they have used and then we will do some changes and we will see what is happening randomly we will put some values in compression ratio very high compression ratio and just see what is happening to the output. So now let's go to this tutorials. We will go to this engine performance and we will open this SI. Now as mentioned earlier when we open from any tutorial or examples we don't have any rights to change this and therefore what you should do is you should do save as and then you should save in your local folder.

So I'll go here and name as session 2. So now this is a single cylinder SI engine. Now this is a port injection. We can see that there is a port, intake port and then there is an injector here. And what is the bore and stroke. So if I go here and check the bore and stroke of this engine. So this is 86 is a bore. So this is bore and stroke both are same. This is called a square engine. So it has a compression ratio of 9.5. So from the compression ratio we can easily find out whether the engine is SI or the CI engine. So when there is a ratio compression ratio is very low.

So as I mentioned earlier the SI engine has a compression ratio in the range of 10, 10.5, 11. For CNG engine it can go up to 12 but not more than that because of the knocking. So now let's go one by one. So this is the environment inlet and then from here we have this intake runner and then intake port. Now in the port there is an injection. So there is a SI this injector fuel injector what we call and this is very simple fuel injector.

So this is we can see here what is the template they are used. So this is injection air fuel sequence connection. So this is a sequential injector with imposed air fuel ratio. So now this lambda SI engine lambda is very very important. So we'll go back to slides after some time and then I will explain you what is this lambda and what is the significance of this lambda air fuel ratio. So now if I see here this is a very basic template and now if I want I can just go to the template help and I can see what is there. So I will I can read this and I can understand each and every attribute what they mean and what the values we should put there.

So we can go into this and then we can understand different attributes as I mentioned. So in the rate we have to mention the what is the delivery rate of that particular injector. What is the value we want air to fuel so 14.5. So now if you go back to your let's say 11.12 standard where we have learned this stoichiometric air flow ratio. So we know what is the stoichiometric air flow ratio. What do you mean by stoichiometric air flow ratio. So stoichiometric air flow ratio is nothing but the exact amount of air required to burn 1 kg of fuel.

So if I take a stoichiometric air flow ratio for gasoline engine so it is 14.5 means what to burn 1 kg of fuel I require 14.5 kg of air. So in that case there will be complete combustion means what there will in output we will get CO2 H2O and 2. So this is very theoretical cycle. So this is very theoretical cycle. But now for SI engine we have to see that a air flow ratio actual should be exactly equal to the stoichiometric air flow ratio. And therefore there is a lambda sensor in SI engine which takes care of this thing. So there is a timing we can mention what is the injection timing angle when we are injecting the fuel.

So obviously being a port injection we have to inject the fuel in the intake port and not in the cylinder. So there is a basic difference in case of gasoline direct injection we inject in the cylinder after intake wall is closed. Now here as we are injecting in the port we have to inject in the intake port and then that air and fuel mixture will travel with air through the port in the cylinder. And therefore I mentioned that if now during the wall overlap chances that the intake this mixture may directly pass to the exhaust.

And if goes to the exhaust then hydrocarbon emissions will be on higher side. So now because of this stringent emission norms we are moving towards this GDI everywhere. So now this environment inlet then runner then intake port then we got it goes to the intake wall and then according to the timing intake wall when intake wall opens this fresher will enter into the cylinder. So if I go to the cylinder what I can see is that in this it is a part of a template engine cylinder and then we have to define so many things here.

So we have to define what is the initial state object. Now what is this initial state object initial state of as I said this nothing but a numerical methods which we need to solve and for numerical methods we have to provide the initial values. So always we have to provide the initial values and therefore we have to provide the initial values and therefore we can mention some initial values here so let's say 1 bar and 300 degrees and 300 Kelvin and a wall temperature objects. So this I was mentioning right now here we are not doing any cooling system design.

So what I am assuming is that I am directly imposing the temperature of the material. So there is a head there is a piston there is a cylinder now in SI engine generally aluminium head block is of aluminium to reduce the weight. And now I can define the what are the temperatures of that material. So I need not to bother whether my water pump is giving me enough flow rate so that I can maintain the temperatures. I need not to bother about that I am directly imposing the temperature that okay these are the head temperature piston temperature and cylinder temperature.

Let's see if I don't want this I want to predict what is the cylinder temperature what will happen if my flow rate is this much. So instead of this wall I will use the different temperature. So that is called engine cylinder T wall detail and if I go here I need to define different different things here. So we will not go into that area so even if I say this this wall solution. So I have to define each and everything. So cooling boundary conditions what is the coolant temperature cylinder temperature so many things we need to define.

So generally I don't recommend students to start with this advanced template. So we should always go step by step similarly right we never directly sit for fourth engineering. Fourth year we start with first year then second year third is similarly like when you start learning any simulation software any tool. Always start with basics don't involve a complexity at the start yourself otherwise you will lose the confidence. Slowly slowly you can go to the complexity you can increase the complexity level. So it's always good practice to start with this basic T wall temperature that is an engine cylinder T wall.

Now this is a heat transfer now what is the heat transfer object. So what happens in the cylinder the gas temperature which is very high because there is actually combustion. And because of this high gas temperature that gas temperature is transferred to the engine cylinder block engine head with convection. Correct. So there is a convection and then heat transfer coefficients are very high. That convective heat transfer then through the solid there is a conduction in the cylinder and then again from the other side of the cylinder there is a coolant.

So that coolant will carry that heat and then it will maintain the temperatures. That's what we have done in wall temperature that we have defined the wall temperatures and now this heat transfer object if I go here. So this is a part of this engine cylinder heat transfer template. Now here I have to define which heat transfer model I should use. So if I want to understand now I can go to the template help and I can see this Vashni GT they have preferred. There is a flow there is a Vashni classic then Vashni swirl.

So there are different different models available for different different purpose. So as of now we can stick to this default Vashni GT and we can go ahead and now there is a calibration parameter overall convection multiplier. So this is by default one. Now to match let's see if I have the results I can to match those results or test data we can have this calibration multiplier. Now the next important thing is the combustion oil. So here also now as I mentioned in the session one. we we Non-predictive combustion model and predictive combustion model. So depending on what application we can define, we can start with non-predictive combustion model, we can build our complete engine model. And then once this is done, we can move to the predictive combustion. So in predictive combustion means what? It will be sensitive to the input parameters. So if I change the spark plug timing, if I change the intensity of the spark plug, so it will have impact on the performance as well as emissions. So in case of non-predictive combustions, now here what was selected is a non-predictive combustion, which is a V-Bay. So SI V-Bay is very basic and we should use this. It requires very less parameters. So there is a 50% burn point that is called anchor angle. There's a duration, there's a burn duration and there's a V-Bay exponent. So these three parameters are sufficient and then we can keep this default values. We should not change these default values. We should not change these values. As of now, we will let us see in this SI case study that how this will have impact on the performance and emission.

Now if you go to the advance here, we can activate this NOC model. We can have this NOC reference object, COO object and then we can even project the emission model. Now by default it is ignored. Let's say I want to add the NOC reference object. So there's always we can do that. So there's a value selector. If I click on this, it will show the available template. So let's say if I select engine cylinder NOC, if I click OK, then first thing it will ask is that object name. So always we have to define object name. So let's this is a NOC and then which model.

So let's extend the model I'm using. Let's say OK. Similarly for CO reference object. If I click here. Available is only one template. So there's no option engine cylinder COO. I will be selecting and let it be the default values. So I will define this as a COO. Let's say OK pre-explanatory multiply as default. Activation temperature multiply as defined. So we can start with the default values. So similarly, so now I can get this NOC and COO even in the emissions. Now as I said, if I want, I can activate this plot. So now let's say in cylinder combustion, I want to see what is the in cylinder pressure. I want to see PV diagram, pumping loop, wall mass. So I can activate whatever I want. But as I said, I want to see what is the in cylinder pressure.

So similarly, I don't activate all plots unnecessarily. It will increase the file size. This should not be problem if you are solving, let's say one or two or less a three few cases. But let's say when we run DOE unnecessary file size will be very huge. So we should avoid unnecessary activation of the plots. So let's say I want to see heat transfer rate. Then combustion, I want to say what is the band rate. Then let's say I want to see incident energy balance. In composition, I want to see let's say what is the NOX value, NO value. So this we will not touch. Let's say OK.

So in GTBAR we have to always before run we have to activate the plots. We have to whatever whichever the plots we are interested in, we should first go to that template and we should act. Let's say now in this intake wall, I want to activate mass flow rate is already there. Lift is there. As I want to see MAC number, I should activate that. So we have seen now this cylinder template. Now let's go to this engine template. So now engine template. What we have to define is whether it is four stroke. What is the RPM engine speed. Now what we can see here is a parameter. They already defined this as a parameter. So we have seen this yesterday. What is the use of this parameter? So now I need not to create different different files, but in the same file I can run different different cases. So that is advantage with the this parameter. Now similarly here now this engine friction. So what are the models they have used by default is.

This engine friction CF where I have to define those constants. So let it be the default values. If I go to the cylinder geometry object. What I can see is a bow stroke, conrol length, compression ratio, TDC clear and side. Let it be the default values. Let it be the default values. We are not changing that firing order. Now being a single cylinder, we need not to worry about the firing order. But let's say if it is a three cylinder and the firing order is let's say one, three, two. So I should define here as cylinder number three, cylinder number two. And then what is the firing interval? If it is a three cylinder, then obviously the firing interval is equal to 720 divided by number of cylinders.

So number of cylinders. So number three. So if I divide by seven to 720, I will get 240 degrees. So I should mention here 240, 240. So the first will fire and let's say zero, then third will fire 240 degree after that and two will fire 240 after that. So it's like in 720 degree. So it's like in 720 degree. So it's like in 720 degree. So now in this RLT norms, this is very important. So there is something called volumetric efficiency with respect to ambient and volumetric efficiency with respect manifold. So this we will see in the CI engine. What do you mean by manifold volumetric efficiency?

But as of now, we have to always define some criteria for defining the volumetric efficiency? So this is an issue. So one bar and 300. So whatever the volumetric efficiency it will calculate, the base will be one bar and 300 degree. So let's say if we if we is telling the volumetric efficiency is 95 percent. So that will be with respect to those conditions. Now we are seeing this engine. Now we are seeing this engine cylinder. Now let's go start with this environment. Now in this environment. So now this is environment is what the surrounding temperature and pressure. So this is one bar and 300 degree Kelvin.

If I want to say if I want to say if I want to say if I want to say if I want to operate this engine at high altitude so I can activate this high altitude and I can mention at what altitude let's say if it is at 2000 meter. So I can just simply put 2000 meter here and I can start the run. Okay. Now I am not doing any changes here. So therefore I am canceling this. Now this environment then there is a intake runner. Generally after environment inlet there is a air filter and then from air filter it goes to the intake runner. Directly don't go to the runner.

But being a simple engine model. They have not bother to model the air filter. This we will see maybe in CI engine. Now this air will be traveling from environment to the runner. From runner then it goes to the intake port. Now this port is very important. For SI engine there is something called a tumble port or director port. So there is a difference in SI and CI engine port. The CI engine port will have helical that is called helical port because we required a helix to generate the swirl. But in case of SI engine we don't require helix. So there is something called a tumble. So this tumble we will see in our next session. Now there is a intake valve. Now yeah before I forget now this intake port if I click what I can see is that if I go here no friction pressure losses.

So we are putting that there are no friction losses in the intake port. So we are putting that there are no friction losses in the intake port because intake ports are very smooth. And what we are putting that there are no friction losses in the intake port. So we are putting that in the intake port. And what we do generally in case of intake port. The water the flow there is something called the flow coefficient of the intake port. So that we generally define in the flow coefficient. So if I go to the intake wall you will see there is something called a flow coefficient. And then we have to define this flow coefficient with respect to lift. So this is not a lift exactly but lift divided by this wall reference diameter.

So this is nothing but generally a wall seat ID or we can define even with respect to bore also. But this is a wall seat ID. And if I divide by the lift values L by D I will get this ratio. So I have to float. So you will see that this is something called a flow variant flow coefficient. So already these pressure losses has been accounted in this flow coefficient. And therefore I should not model the friction here. Pressure losses in the intake port. Otherwise it will lead to the error. Because in intake port also we have to calculate. It will calculate the delta P and in the intake wall flow coefficient also it will calculate. So there will be like addition of the pressure losses.

So we should not do this way. So we should not do this way. Intake port we have to always ensure that intake the diameter at the inlet and outlet at the same. And then what are the pressure losses we have to account using the flow equation. So this general data we have to get from the test figure. Similarly when you go to the exhaust. Similarly when you go to the exhaust wall. Similarly in exhaust wall also we have to define this flow equation. And generally what you can see this exhaust flow equations will be on higher side if I compare the flow equations of exhaust and intake exhaust flow equations will.

Because in exhaust I need not to generate any kind of motion like what we do in diesel engine, helical port. So here we don't have this. Then again exhaust port similar to the intake port here also we should not model any friction, pressure drop and then because already we have accounted this in intake flow coefficient, sorry exhaust flow coefficient. Then from exhaust port it goes to the exhaust runner and then from exhaust runner it goes to the ambient again. So ambient is nothing but one bar and 300 km.

Part 3

Now let's go back to some basics and then we will come back and we will do some modifications in this engine. So what is equivalence ratio? So equivalence ratio is nothing but it is a ratio of air fill ratio strichometric to the air fill ratio actual. Generally people use a lambda which is a reciprocal of the equivalence ratio. So lambda is 1 upon 5 or nothing but air fill ratio actual upon air fill ratio strichometric. So this is very important parameter. So there's one comment below is that diesel engines are lean burn and gasoline engines operate at equivalence ratio equal to 1 or lambda equal to 1. So there is a reason behind that. So now what is the main what do you mean by lean burn? Lean burn means what the amount of air is more than required strichometric air flow ratio. So let's take example of gasoline. Now gasoline what is a strichometric air flow ratio is 14.5. It means what to burn 1 kg of fuel we require 14.5 kg of air or let's say 1 gram of fuel we require 14.5 gram of air in the cylinder. So that is what our requirement. Now if let's say in actually the amount of air this amount of fuel we want to burn is let's say 1 gram and the available air is let's say 16 gram. So if I take the air flow ratio actual it will be 16 upon 1 and what is the strichometric air flow ratio is 14.5 upon 1. So if I divide 6 air flow ratio actual to the air flow ratio strichometric what I will get that the lambda will be more than 1. When lambda is more than 1 it means it is a lean burn or the other way in terms of equivalence ratio if phi is less than 1 because it is reciprocal of lambda. So obviously if lambda is more than 1 then phi should be less than 1. So it is a lean mix. So why diesel engines are lean burn that we will see in our compression ignition session but gasoline engines operate always at equivalence ratio equal to 1 or lambda equal to 1. So we will see next figure. So this next figure it will it what it is showing is uh fuel on x-axis there is a fuel equivalence ratio phi. So as we have seen that when phi is less than 1 this is called a lean burn and when phi is more than 1 this is the reach okay. So now I am talking in terms of phi. So if it is less than 1 phi it is a lean burn. Now on y-axis there is a combustion efficiency. So if I plot combustion efficiency with respect to equivalence ratio what I can see is that the combustion efficiency is horizontal or unaffected in the lean zone but the moment it becomes rich it drops exponentially. So it goes down very fast. The reason is obviously what is important for burning is air. Fuel cannot burn on its own. What we require to burn is fuel. So air. So if air is not there so fuel will not burn and it will come out as a co and hc carbon monoxide and hydrocarbon. So it is nothing but a incomplete combustion and therefore if I see the combustion efficiency it drops exponentially. So if it becomes a richer by let's say 1.1 it is almost dropping by 10 percent. The combustion efficiency drops by 10 percent.

So this is very important. You have to always ensure that your lambda is equal to 1. Now what is the wrong in running at lean? What happens when there is a lean mixture? The amount of air is more. It means what the incoming N2 which comes with air is on higher side obviously because the amount of air is higher and therefore NOx formation will be on higher side. So lean mixture a gasoline engine will give you better fuel efficiency but higher NOx. Another case a rich fuel mixture will give you lower NOx but very bad fuel efficiency or even the emissions will be on higher side. But strategically at some points we have to go richer for some reason that we will see why. So consider this is a lambda map of one engine. So if I see this engine speed versus BMP so now this is the minimum speed of engine 900 rpm and then it goes up to 6500 rpm. If I calculate the BMP and if I plot this BMP of this engine I'll get this curve like this.

Now see the lambda region. So lambda is equal to 1 at the majority of the zone but at some point we can see here lambda. This zone the lambda is less than 1 it means in this zone the mixture is richer and if I see here this towards the left zone the lambda is more than 1 it means it is leaner in this zone. So why we are going with rich combustion in this particular zone because what happens in gasoline engine the exhaust temperatures goes very high it goes up to let's say 900 1000 degree centigrade engine if I'm operating at very high BMP engine high BMP level the exhaust temperatures goes very high and now if they are going very high what will happen the exhaust temperatures if they are very high the material this exhaust manifold exhaust wall exhaust wall seat will have the less life and durability will be a main issue with that and therefore to avoid that what we do purposely we put extra fuel to make it richer so that the combustion efficiency drops and because of that exhaust temperatures comes down. So therefore this is a something for the safety reason so this is the importance of the lambda now we all are aware right this is a four stroke engine two stroke engines are outdated so we will not talk about that so this is let's say to complete four strokes we require two revolutions so in first half revolution there is a suction then there is a compression then expansion and then exhaust so these are the four strokes of SI engine or any four stroke engine it can be SI or CI that remains same only difference is about the air fuel mixture so if I go to this operating characteristics what we can see is that there is something called a bore so bore is nothing but this diameter of the cylinder what is stroke they know so this piston reciprocates inside the cylinder so it goes to one one top position and then comes down to one bottom position and then it keeps on reciprocating in between these two so the topmost position is called the tdc and then bottom most position is called a pdc so obviously the piston will not go and hit the head because we need some clearance volume and therefore this is called a clearance volume what is the swept volume then swept volume is nothing but a cylinder pi by four b square into s so this is a swept volume so if let's say uh bore is equal to stroke that is called a square engine generally the case with the passenger application if bore is more than s it is called over square engine this you will see in high speed application let's say racing car or let's say bike engine you will see that bore will be more than the stroke and let's say bore is less than stroke that is called under square engine this you will see for let's say slow engine application let's attractor applications or some other off-road applications where you see the stroke will be more than the bore now what is the compression ratio is the total volume at bdc upon total volume tdc or maybe next figure we will make it clear now when the piston moves to the bdc so this red indicates the volume right so it is the addition of the clearance volume plus swept volume so that is vs plus vc and when the piston moves towards the tdc that is whatever the volume is called a clearance volume so if i take the ratio of the volume at the bdc upon volume at tdc is called a compression ratio higher the compression ratio means what the cylinder pressures will get compressed to the high level and if in cylinder pressures will go very high so this we have seen right these values we put in the engine crank train attributes where we mention bore stroke compression ratio now next important parameter is a power and torque so now torque is measured in newton meter and power is measured in watt hp or ps and power is a function of torque and engine speed so p is equal to 2 pi nt by 60 that we everyone is aware of that so now let's consider this vehicle right so this vehicle when it is moving on a road so which are the different different forces which are acting on the uh any vehicle so this forces if i multiply the vehicle velocity what i will get is the power so that is required power so this power i I have to get it from engine, then only I can maintain a vehicle velocity. So as vehicle moves with higher velocity, this drag resistance goes on increase. Also this rolling resistance. So that is very important and then it changes as per this tire conditions and road conditions. If it is very important to maintain the inflation of the tires correctly, the weight carrying capacity if their vehicles are overloaded, let's say the truck is designed for one ton and if I am putting the two ton, obviously I cannot move with very high velocity because I cannot generate the required power from the engine because engine has limited power, let's say 20, 30 kilowatt, then I cannot generate more than the 30 kilowatt and obviously it will impact the vehicle velocity. So this is a generally a characteristics of any engine power and torque. So this blue line indicates the torque value and this red line indicates the power value. So along the x-axis, we have the engine speed along y-axis, this is the power y-axis is the torque and what we can see is that generally this blue line, right? So the torque goes on increasing, it reaches the highest value, it remains flat for some time and then comes down. And now this torque and engine speed, if I multiply, what I will get is a power. So power is 2 pi NT by 60. So if I just go on multiplying these two vectors, what I will get is increase the power goes on increasing, it will reach to a maximum value and then it will reach to a maximum value and then it will come down after this. So there is something called beyond which what happens the friction goes very high and therefore I have to reduce the power is reduced. So the point at which we get the max torque is called or the engine speed is called intermediate speed and the point at which I will get the max power that speed is called the rate and speed. So obviously whenever you see the any vehicle specifications in engine they will define this two points. They will mention the max power and speed and then max torque and speed. So that will give you a rough idea. Okay, whether my engine is suitable for particular application or not. So now let's go to the SI engine modeling. Now, now this we have seen, right? So this is a tutorial example. Now you can just go back and you open the tutorial and you can start developing this model. It's very easy, but you should do this. Don't directly just open the tutorial and start. What I can recommend is that you can start. What I can recommend is that you first go to the tutorial and start from the scratch and generate this model. So once this is done, you can have this whatever I'm doing now. Maybe you can practice after. So now let's see case setup for this engine. Now this engine is running at 3600 RPM. Correct? So this is a case number one. Now why I am seeing in case setup this particular parameter?

Because I have defined this RPM. So if I want to see where I define I have to just right click and I have to see show the parameter usage. So it will show me where it has been defined. So it has been defined in the engine crank train template and the part crank train. So it has been defined. So I can go there and I can say edit object. Then it will directly take me to that particular parameter. So there I have defined this as a RPM. So now if I want to change I want to add more cases I want to add more cases I can do that very easily. But before that let's see what I'm doing. Now if I run this. Now how much power it will this engine will be developed. Where I have defined the fueling and everything.

So here you can see. So here you can see. So now what I have defined is the injector delivery rate is 6 gram per second. But here I have not defined a total fuel. How much fuel we are injecting. We have just defined the delivery rate. That this particular injector can give 6 gram per second. But how much fuel it should inject. We have not defined. So how engine will calculate that how much power it should develop. How much fuel it should inject. So let's now run this. So let's now run this. When I see the run. It will open this wizard simulation wizard. So I can click on show runtime monitors. We have to deactivate the parallel case. And then here I can define the number of periods. Okay. And then the simulation options. You have to put show graphical user interface. Then show graphical user interface. And then there are other options also. Continue to next case after fertilizer. But we will talk about this later during the optimization.

So now if I see the finish. So now if I see the finish. Yeah. This wizard. And then. It will show me more values. Anytime I can switch to the traditional messaging. But now this will show me. Okay. How many cases it is running. What is the case progress. And that will give me idea. Okay. How much time it will further take. So if it is only one case. We need not to worry. But let's say there are more cases. Then that will give me. Okay. Now case one has been run. Case two is running. So in a simultaneously. It will report some parameters also here. So what is the volumetric efficiency. How much I may be. What is the max pressure indicated efficiency. So these also I can see. Now if I want to see this. I can just go to the view result. But before that what we can see is that how much period it has taken.

Within six period it has converged. Within six period it has converged. And what is the total time. It has solved is 0.2 seconds. So total in within 0.2 seconds. It has converged. So if I want to see the results. Just go there. So if I click on the view results. It will open the gtpost now. To take some time. Because it gathers some required templates. Before opening. Now you will see that it will open one scratchpad here. And then session. That particular model. Session two. And then here it will open the plot window. So now in this case we will have the plots. Case RLT. Time RLT. And report tappers. And plots. It will show the plots which we have selected. Now if we.

Just go here. I can see. Let's say pressure. I can see here. So I can right click. And see view. Or I can just directly. Click on this. And press F4. So it will show me. So this is the. In cylinder pressure. So on x axis. It will show the. Different zones. Four zones. Compression. Power. Exhaust. And intake. And then. We can see that. So how this. In cylinder pressure. So if I want. I can. See this. Okay minimum angle should be 0. From 0 to 720.

this way. Or I can see. Or I can say minimum angle is. Minus 180. And then I can see. Or let's see if I want. I can see. Minus 360. So exactly. It will be at the center. So what it is showing. Is that. There is a suction. There is a compression. And then compression. This cylinder. It will increase. And then it will. Burn the fuel. And there will be power stroke. And then there will be. Exhaust stroke. Similarly. If I want to see. PV diagram. We can just. Right click. And save view.

So it will show me. So now. This is not theoretical. This is actual. So theoretically. It is. Everywhere. It is. Exactly. Vertical. But now. It is not the case. So. We can see this. Right. PV diagram. So this is a clockwise. Then we can see the pumping loop. So this pumping loop is nothing but. So we can see here. This pink line. Is. For intake. So we can then. Pumping loop. We can see. This is a cylinder pressure. Exhaust pressure. Intake pressure. And intake and. Exhaust lift also. So it is showing me. If I want. I can just.

change the properties. Just double click on this. And save weight. I want to increase the weight of this. You can say. Okay. Here else I can double click. And say I want. Weight. So now. What you can see is that. The intake wall opens. And then it goes to the max wall lift. And then. Start closing. Similarly. This exhaust wall open here. And goes to the maximum value. And. Exhaust wall. So now. Observe this period. So this zone. What we can see is. Intake wall has all started opening. And exhaust wall is about to close.

So this zone. Your intake and exhaust wall. Both are open. So that is called a wall overlap period. And there are chances that. The intake will directly bypass to the exhaust. So this wall overlap period. We need to tune properly. Or. This pumping loop will not give me a good idea. Let's. How this wall mask flows. Now see. We can just go back. And. Click. Zero. So that. Everything will be at the center. Similarly. We can change. The properties. We can go here. And. Change the weight.

Similarly. If I want. So now. This is better now. So now. See. What is happening. This blue is indicating the intake. Air flow rate. And. Red is indicating the exhaust. So. Now let's align this. Let's. Switch off this. Exhaust flow. And exhaust wall lip. And just see what is happening. So now there is a suction. Exhaust flow. Thank you. And during the intake stroke, I have opened the intake wall before TDC, intake is opening and simultaneously when the intake wall has opened, air has started coming to the cylinder.

So this is how it is coming and then going. And now here what has happened? Now I should have closed wall here, but as the wall is open, intake wall has not closed it. What is happening? There is a reverse loop. So whatever the air which has come to the cylinder is going back. So this is called a backflow. Now this wall timing has very, very important role. This IV-C intake wall closure. So if I don't have the correct wall timings, what will happen? Whatever the trap mass will go back.

And then I can avoid this by changing the wall timings. But physically I cannot change wall timings, right? With respect to engine because once I make the camshaft, I cannot do this changes. But there are some mechanisms available. Let's see if you remember this Honda IV-TEC or what we people today call is Fiat Multi-Jet, Multi-Air technology, so many names to the same technology, variable wall timings. So I can change with the mechanism, I can change this wall timings. And according to the engine speed, I can tune that.

So if you are really interested, you can just search Honda IV-TEC and then you can understand how the camshaft changes is or how we can change the wall timings, closing timings and get the advantage of this mass trap. So that we can have the more amount of air in the cylinder. So if you have the more air, I can burn more. Well, that's simple. So it is very important that we should have more air in the cylinder. So this is about the intake.

Part 4

Now if I just activate the exhaust so we can see that when there's exhaust will open there's a sudden pulse that is called a blowdown pulse then it comes on then but still piston is coming from BDC to TDC and therefore the there is a second pulse so this is exhaust wall opening and closing so this is called a wall mass flow so this we can understand now see what is happening when I'm opening a new this post processing window the early window is getting close so what I can do I can just go to the file go to the options plot table viewing I can just create automatically create snapshot when plotting so now when I do this and now if I open let's say PV diagram what it is doing it is directly taking the snapshot and saving so I need not to plot this again and again once I do this automatically it will take the snapshot and it will keep the earlier window as well as the earlier window as well so now I can have this PV diagram wall mass flow rate everything so always it's good to activate that option so this is about the very simple model what I'm doing is I'm just running this now let's say I want to see it so this what we have seen is there are the plots let's say I want to see what are the other parameters so I'm just going to report tables and right click and right click and right click and save view or I can just press F4 so now here it will give me everything the important parameters so what is the bow stroke of that engine these are the inputs and then it is showing me something in the vault timings so this vault timings I will cover in the next session how to read this vault timings so as of now I'm just keeping this now see here what is the injection start we have not defined anything we have defined the combustion start at minus 18 okay so rpm is 3600 now how much power it has developed 16.3 how much brake torque is 43.3 how much I MEP is 12.6 so every it will report all each and every parameter how much air flow rate is 58.6 how much fuel flow rate is 4 and what is the air flow ratio is 14.5 so now tell me why it has taken the fuel flow rate as a 4 so if you remember so if you remember so if you remember I was asking right in this SI injector I have not defined the amount of fuel how much fuel I have to inject I just define the injector delivery rate but if you see here the fuel specific fuel ratio specification I have defined this air to fuel and I have mentioned the air fuel ratio as 14.5 means what it has to maintain a air fuel ratio of 14.5 so what it has done it has first calculated how much amount of air is going into the cylinder 58.6 so if I just do some basic calculation that's a calculator so it's a 58.6 and if I divide this by 14.5 and it has a 4 so from here then it calculated that how much fuel it can put is 4 and not more than that and that's the reason how much power torque I have got is 43.3 so it's because that lambda so it has maintained the lambda as 1 because 14.5 is a seismometric air flow ratio so it has maintained the same air flow ratio as seismometric now if I want to increase the power of this engine what I should do let's say I want to increase this torque value what are the different solutions available either I can change this air flow ratio so that I can put more fuel so I can go let's say richer instead of 14.5 I can mention let's say 14 so it will put more fuel and then I can get more torque or otherwise what I should do is I should get more amount of air in the engine how that is possible how I can get more amount of air in the engine one possibility is that turbo charge the engine or less what we call the super charge the engine or we can change the bore and stroke of the engine or I can have the more bigger size swept volume I will increase and if I increase the swept volume nothing but the breathing capacity will increase so it will have the more amount of air in the engine and then I can burn more fuel in that case so this may be I will give as you assignment so which we will discuss later now see that BSFC's value achieve that BSFC value as 247.54 means what to generate 1 kilowatt of fuel power how much fuel it is consuming 247 gram per hour or 0.247 kg per hour so it is consuming that much amount of air it is that simple then we have something called volumetric efficiency so you will see two terms one volumetric efficiency this is with respect to ambient and M indicates the manifold so this is relevant manifold is relevant in case of turbo charge engine but for naturally aspirated engine it is always with respect to ambient so this is 93.6 so similarly it will report in US nomenclature and then here we can have the key cylinder production so it will give me the amount of the residual fractions amount of the max pressure as a max in cylinder pressure and what is the crank angle and now these two parameters pressure this crank angle they are sensitive to this VBIP function so if I let's say if I go here and if I change this parameters my values will change so now what we will do we will change the different different parameters and we will understand what is happening how my values are changing now this see the NOX here is 4000 ppm amount of CO is 9138 ppm so this is on very higher side so let's see one by one different different parameters so let's say I want to see the impact of air flow ratios I will define this as a parameter so let's say air fuel ratio and if I click so it will directly ask me go to case setup and then I can define there as a 14.5 now I want to see what is happening if I change the air flow ratio so what I can do is I can just go here and I can say append cases append cases and just see what is happening so let's say in one case it is richer 13 then 14.5 and let's say 16 now if I run these three cases let's see what is happening so now I am running three cases back to back now simulation is run let's view the results now we have run the three cases so instead of seeing case one by one we can directly compare this so we have to just go to the macros and in macros we have to see this combined data we can select all three cases and we can select which things we want to see together so we can just select all and then we say combine all cases in each table just say okay so then it will show me all three cases side by side so now see here what I have done here is I have changed up so in case number one my air flow ratio was richer it was 13 then in 14.5 and 16 so now when if it is rich mixture what I should expect is a more amount of emissions in the exhaust because amount of air is less so co will be on higher side but nox will be on nose lower side and in this case it is linear so in if it is a linear my co amount should be on lower side so let's see what has happened uh to the brake torque now this is a 43.9 this is 43.3 and this is 40.1 because I am putting less amount of fuel so here I am putting 4.5 4 and 3.6 so here you will see that even I have increased the fuel it has not increased the brake torque in that proportion because the amount of fuel couldn't get converted into torque because it remained unburnt and that straight of it is coming out as a emission pollutants so it has not converted into a brake torque but in this case what has happened because I have mentioned the leaner so it has divided this air flow rate by 16 and therefore it could only inject 3.6 and therefore the torque has been reduced now see what has happened to the performance parameters let's say now here the we can see the bsfc now you can see that is increase more amount of fail so if you compare case one and two You In case 2, only 247.4 gram was required and now it has increased to 273.1 to generate 1 kilowatt of power because amount of fuel A has been wasted.

Now let's see what has happened to the emissions. See this NOx, right? So NOx in PPM. So it has reduced in case 1, case 2 and case 3 it has increased. But see what has happened to the CO emissions. CO emissions has been increased drastically. From 9,000 it has go up to 41,000. And see in case of case number 3, the CO is very low. So this is how we can understand the impact of different parameters on performance and emission. Now let's see what has happened if I change some other parameter.

Let's say if I go to the cylinder and if I go to the combustion, let's define this as a parameter. So this is generally called MFB50. Let's say duration. So duration, this is called duration of combustion. Now if I go to the case setup, MFB50. Now let's say I don't want, I want to compare at the same air fill ratio. So I will go back to 14.5. Now this MFB50. What should be the MFB50? Generally for this gasoline engine, MFB50 should be exactly 8. That will give me the best DSFC.

But what is allowed is let's say 8 to 12 degree. Within 8 to 12 degree, we should get the value. Now let's see what will happen. Now this is a, let's say I am putting this 8. The next case I am putting this as 12. And let's say this is 16. Dosis of combustion, let it be 25. Everywhere. And let's see what is happening. If I run this, yes, I would like to continue, yes. So now here we can see how many cases, case, all three cases has been run.

Now observe one thing. Now see the case number three has been completed in only three periods. Why this has happened? Case one, it took six periods. But case two and three, it has taken only three periods. Because if you go back and just see the run setup, initialization, right? So always it starts with initial values. So for case one, the initialization was like we guess some numbers and then we put some, let's say one bar, 10 temperatures, pressures, we put some values. But now see the initialization state.

What we are defining here is previous case. Means what, when it will move to the case number two, it will initialize all the components, all the parts with case number one. So case number one and case number two, there are not much variation. So already when it started case number two, almost all the parts it was converged. And then initialization were correct. And therefore case two and case three has converged very fast compared to the case one. So now if I go here and say click, results have been updated.

If I click on that green sentence, what I can just go back and compare now. Now see what we have changed is MFB 50. And see what has happened, 8, 12 and 16 degree. So what has happened, same airflow rate, same fueling, but see the difference in the brake torque. So this, when the MFB 15 was 8 degree, it produces the highest torque compared to the 12 and 16. It means what, when there is a slow burning, because 16 degree, to reach the 50% burn point, it took 16 degree.

In case number one, it took only 8 degree. So that has impacted on its performance. And we got high torque for the same air and the same fuel. This is reflected in the BSFC. So this case number one has the lowest BSFC compared to case number two and three. So case number one has consumed 247 gram of fuel as against case number three, 254. So obviously that indicates that my MFB 50 should be within 8 degree. So there are some calibration measures where we see that always we will stick to lambda equal to one and MFB 50 equal to 8 degree, close to, not exactly 8 degree, but close to 8 degree.

So it can be 10 degree some point, sometime it can be 7 degree, can be 20. So generally between 8 to 12 degree, we try to maintain. So similarly, you can just go back and you can understand different parameters. Just see what has happened to the emission side. Now see the case number one. As it is a fast burning, obviously the rate of temperature rise will be high and therefore the NOx formation will be on higher side compared to the case two and case three. But see what is the CO?

CO also here is on the higher side. So now sometimes to reduce the NOx, what we can do is we can increase the burn duration. Just a measure of NOx control.

Part 5

So similarly we can have different parameters and then we can see the impact, let's say duration of combustion also we can change and we let's say instead of let it be 8 degree or 12 degree everywhere and let's say now MF duration of combustion here it was 12 degree here it was 25 and here it was let's say 30 degree and let's say what is happening, see period 1 has been converged in 6, 2 and 3 within 3. just combine this and just compare what has happened. Now similar the case number 1 was 20 degree then 25 degree and then 30 degree the similar impact what we have seen with MF B50 it's like a burn duration so 20 indicates that it has burn very fast so we can see this similar impact in terms of the BSFC and in terms of your emissions also.

So the case 1 will have the highest value of NOx. Now in 1D the NOx I would say the NOx predictions are quite good but CO, HC the solid pollutants it's very difficult to estimate those values so we have to be very careful when we compare those emissions. It's not that easy to predict the CO and HC from the engine combustion in 1D we require some 3 dimensional tools to predict those very accurately but yeah 1D will give you at least the trends whether it will increase or decrease that's it.

Now if I see the case RLT so what is case RLT so in case RLT it will report with respect to the case number so let's say I want to see the BSFC so I just go there and just see right click and save view so I will see the BSFC with respect to the case number so case number 1, case number 2 and case 3. So this will give me the trend so this will give me the trend so this will give me the trends so it's clearly we can get that BSFC has increased case 1 and case 2 we can see the brake torque torque has decreased that's the reason BSFC has increased we can see let's say emissions and what happened to the NO concentrations we can see that.

Say no has decreased so this will give me the trend so this will give me the trend so this will give me with respect to the case number. Now this is about the single cylinder so this you can practice you can have different parameters and just run I just I wanted to tell you show you that let's say now in this case I define compression ratio as a parameter. Let's say I want to define this as a CR compression ratio and if I go to the case setup let it be that 3600 RPM everywhere let it be the 2525 and now let's say this is 9.5 let's say I want to run only 2 cases so I will delete this case and let's say randomly I put some number 18.

Now let's see what is happening whether now this compression ratio 18. We cannot work with this high compression ratio at least for SI engine definitely it will lead to the knock but that's what I was telling right junk in a junk out whether let's let's see whether GT is telling me this input is right or wrong. So let's say I am running this 2 cases practically this will not work compression ratio 18 SI engine cannot work. Let's say now what has happened see now report tables go here now see what has happened.

Now almost there is same air flow rate but see what has happened to the break drop from 42.9 it has gone up to 48. What is what is the BSFC 249.5 it has reduced to 218.9 so this is very good numbers right. I've got from 249.5 just by increasing the compression ratio my BSFC has reduced drastically. So this should be very good design. But see what has happened right nothing it has not declared anything so it has just run. So GT will not tell you that okay this SI engine cannot work on this high compression ratio something like that.

No it will just run and it will report the values. Now as an engineer we should know what are the input constraints how much input I can put. Now let's see what has happened to the in cylinder pressure. Earlier the pressure was 53 now it is 88.7. Very high amount of in cylinder pressures. Now see the DP by DK that is change of the rate of change of the pressure. So this is 1.8 and it has almost 2.8. So this high change of pressure is an indicator that the rate of pressure rise is very high and there are chances that there is a knocking.

So it is like some thumb rules you should be aware while modeling. We should not just put any random inputs. We can refer different different books available in the market. The Saganation is one of the good book or maybe this Fundamentals of Ice Engine by Hayward. You can refer that books or Pulka Break. And then we can get those fillings that okay what should be the range of the inputs if it is not available. So it is like we have to be very careful while putting those inputs.

Now similarly if you just go and explore these example files. You will find lot of examples. If you just go to Engine 1D Gas Exchange Combustion. If you go to the Gasoline. There are so many models. So we can explore one by one. Let's say 4 Cylinder Basic. Then 4 Cylinder EGR Controller. Then 4 Cylinder GDI. Now as I said we have to always go and save as into our local folder. Now this is a 4 Cylinder SI engine GDI model. Now see when I go to the GDI.

Now if I compare here right. Where was my injector? It was in the intake port. Now in case of GDI. It has moved in the cylinder. Again I have used a very simple injection air flow controller. And I have given the injector delivery rate at 6. Now see some. This is yellow right. If I click here. I cannot change anything. It is not editable. Why? Because now if you see here. This is not a single injector. It is a single cylinder. So this is a multi cylinder.

So in the same template. We have this object. And in under object. We have these 4 parts. So now. If I want to change. I should do change in the object. So that it will be reflected everywhere. Let's say if I put 6.5 instead of. Let's say I want to put 7. And now if I go back. Then it will be. Save changes. Yes. It will be reflected in all parts. So now see here. Everywhere it is 7. Okay. So just go back to 6.5. So it's like when.

We have the multiple parts. And the same object. It will be reflected in yellow. Just to give you indication that. There are more parts in the same object. If you want to do changes. You should do in the object. Or let's say if I want to do changes. Only for that particular part. In the same object. Family. Let's say if I want to change. For only 6.5. I want to change only for 7. So there is something called. Override. So if I put 7. It will be reflected.

Only for that particular. Part. And not other parts. So if I go to the. Sequential injection 2. It will be 6.5 only. But for only. Sequential injection 1. I can put. So this will be. Highlighted in the color red. The. Overwrite parts. So this is a GDI engine. Okay. Now here we have used different, different, the almost same SI VB function only is like a TAG50. Now see the difference. In earlier case, if I go back to our earlier model, here it was a single value. So I define a parameter and I'm defining that MFB50 as let's say 8 degree, 12 degree or something like that.

Let's say I want to define that as a function of some other parameters. Now let's say this MFB50 in this, I don't want to put a single value, but a table and which will be a function of some other parameters. So there is something called RLT dependence X, Y. So this template is very important RLT dependence X, Y. So now instead of putting a single value, I will put in terms of a table and this now table will be a function of engine RPM. So how to put this? We can say this. So when the engine speed is 1000 RPM, the value will be 12, when 2000 RPM, 9.6.

So automatically GT will take the relevant input as per the engine speed. Okay. So this is a function of X only. And so there is a Y. So for one particular X, there is a particular Y value. So this is X, Y, there is a X, Y, Z also. So if I want to instead of only engine speed, let's say I want to put a function of let's say some more parameters, some one more. So instead of X, Y, I will select X, Y, Z. so let's say engine speed BMP so in x-axis there will be engine speed on y-axis there will be say fueling and for that x particular engine speed and particular fueling there will be particular z value so x y z so that is also possible so we can do that way listen of one duration also they have defined as a function of x and y so at one particular speed it will directly so this we can define here which parameter so here let's say I want to put engine RPM so I can just from value selector I can go here and then I can select my engine speed let's say I want that to be dependent on let's say air flow rate so I can just go here and I can select air flow rate so instead of a function of engine speed it will be a function of air flow rate so this is called a RLT dependence x y or x y z so no need to give in in parameter format so at different different engine speed automatically it will so let's say for case number one 6000 RPM it will take some value at 2000 RPM it will take some value which is mentioned in that particular table so this is a four cylinder GDI engine so now see here what they have done they have done a modeling in detail so it starts with so let's say this is an environment and it goes to the intake pipe then in different there's a Helmos resonator then from here it goes to the air box so now they have modeled the air box as a volume and then we can access the air filter drop here from air filter goes to intake pipe then it goes to the throttle so there's for SI engine torque is controlled by or the failing is controlled by throttling so I by throttling I can change the amount of air going to the engine and then accordingly amount of air if I amount of air it change obviously the amount of fuel will change because I have to maintain the lambda so always it will divide the amount of air by the systematic air flow ratio or whatever the mentioned value lambda value and then it will find the amount of fuel and accordingly amount of fuel will be injected so now this is gasoline direct injection so fueling will be injected inside the in the cylinder so from here then it goes to the intake manifold then it goes to the intake runner then from intake runner it goes to the intake port so now this is not a two wall this is a four wall so there will be two intake wall and two exhaust wall unlike in our single cylinder it there was only two wall so only one intake one exhaust now here it's a four wall arrangement so two intake and two exhaust and then from here then again goes to the exhaust manifold from exhaust manifold then it goes to the catalytic converter so this is after treatment so now this this is a part of our one session where I'll be going in detail of the catalytic converters that is reduction and oxidation so we will see how this three-way catalytic converter works and how this scr works in detail so this is four cylinder one now what we have done so we have defined defined different different parameters now let's see which are the different different parameters how define the ambient pressure and temperature so if I want to change I can just change from one bar to some other value and let's say now this is a number of rpm engine speed and the throttle angle now if I run the six also there are four total five cases I'm just running six thousand five thousand four thousand three thousand and two thousand rpm so if I go here and if I just click on run now after this run I will just show you the assignment for the next week and then you can go through that and then next week we will have the case study on this engine so now it is running one by one so case number one has been finished so 20 percent so that shows the progress so now case one has been completed out of a total five cases case two is running it has finished 30 percent 33 percent 90 and 100 percent so case two has been completed so this gives me the progress as well what is happening so total five cases I am running so ongoing case is a 3000 rpm I am ep develop studying then a case number four is going on faster case number five is going on so it will record some parameters actually here so it will report that end of front so always we have to see the any if any it has any messages earlier so now this when simulation runs it generates the post processing process gt model file is gtm that is called dot gtm the output file is called dot gdx then at the same time it reports dot out file also where it will list on all the messages or message file dot msh file so all this path this details we can see in the dot out file now we can we want to see this let's say report tables we can combine this data all this data so we can do this or we can directly select all and say engine and cylinder combine so it will report so 6000 so we can see what is the break talk how so now see the break talk or if i want to see i i can see the case rlt that will be the best way now see the air flow ratios hello this is very rich right these two cases so almost all cases because this is all full load points so full load point generally they run rich so if i go to the case rlt if i go to this engine crank train and in favorites i can let's see what is the bsfc so we can see that okay at 2000 then it is going and then it is increasing we can say what is the air flow rate so it is going increasing in that order what is happening to the brake talk so we can see the brake torque so at 2000 rpm it is 150 it goes on increasing goes to the maximum value and then drops so this is a max torque point 4000 rpm then it goes comes down when the brake power if i want to see we can see this increasing and then after some time then it will go and then after this 6000 rpm it will drop so similarly i can see different different parameters how they are behaving so i think that's that's it for today's session so just to summarize we have gone through some of the basics of si engines we have seen some parameters lambda equivalence ratio knocking the limiting factor the octane number the importance of octane number then how the gdi engine configuration is so now this session session was about the si engine modeling techniques now next session we will go through the one case study where it's from the real world we will do some modeling before that maybe you can go to the assignment number two so assignment number two what you have to do is you have to explore the tutorial number one you From the SI final, run the case at 1800 RPM, and we have to list down all the important parameters, which are listed very few, less air flow rate, BMP, BSFC, Insulinder pressures.

And now what next you have to do is, you have to increase the power output at 3600 RPM by 10%. So you have to explore the different options, but while doing this, you have to be very careful that it should be feasible. Don't just blindly change any value and increase the torque, increase the power. My target is that whatever, so first thing you have to report is 3600 RPM, what is the power, and then you have to achieve the 10% increase in the power output by changing some parameters.

So that's it for today's sessions. Our next session, next week will be on the case study on SI engine. Till that time, bye. Thank you for your attention.

Want the rest of IC Engine Calibration using GT-POWER and GT-SUITE?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full IC Engine Calibration using GT-POWER and GT-SUITE course

The remaining 9 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full IC Engine Calibration using GT-POWER and GT-SUITE course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.