← Previous lessonFree lesson 3 of 4 · lesson 3 of 65Next lesson →

Unlock all 65 lessons of Geometric Dimensioning and TolerancingFull course ₹40,000 · paid

Price & syllabus
Free lesson · 37 min · no payment

GD&T Modifier Symbols: MMC, LMC, RFS, Projected and Datum Targets

A free lesson from Skill-Lync's Geometric Dimensioning and Tolerancing course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Introduction to GD&T Symbols”

What will you learn in this free Geometric Dimensioning and Tolerancing lesson?

The instructor defines the symbols used in feature control frames, starting with maximum material condition for holes and pins with worked diameter examples. It then covers LMC, RFS, projected tolerance zone, free state, datum symbols and datum targets, and ends with a symmetry callout and a symbol quiz.

  • MMC for holes and pins from a plus-minus diameter
  • How LMC works opposite to MMC
  • Projected tolerance zone and free state symbols
  • Datum symbols, datum targets and a symmetry callout

What comes after lesson 3?

The next free lesson is lesson 20, “Tolerance Stack-Up Analysis with RSS, MRSS and Worst Case” (21 min). Later in Skill-Lync's Geometric Dimensioning and Tolerancing course (paid): lesson 4, GD&T Lecture 2 - Segment 1; lesson 5, Understanding Form Tolerances in GD&T; lesson 6, Understanding MMC and LMC Conditions in GD&T. The full course has 65 lessons (13 h 6 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Hello everyone. Welcome to my lecture series on GD&T. This is the third segment of the first lecture on GD&T. In the previous segment, we learned about the technical standards used in GD&T and also we learned about how to read a feature control frame. In this segment, we are going to learn about the different symbols in GD&T. Now in feature control frame, you must have studied that a feature control frame consists of certain amount of symbol. The first symbol is the geometric characteristics. The second symbol is the tolerance zone. Again, we put a file only if we are calling out a feature of a hole or a feature of a pin. Then we have the actual tolerance zone. 0.25 is the actual tolerance that we need. And then we have the datums A, B and C.

But sometimes you must have noticed that in some feature control frame, there are different symbols used. Sometimes there is an M over here, M over here, here, here. Or sometimes there is an L over here. So, in this segment, we are going to learn all the symbols that can be used in the feature control frame. Symbols is nothing but it can be considered as alphabet of the language, which tells me what the actual feature control frame means. So, let us start with the first symbol, that is the MMC or the maximum material condition.

So, MMC or the maximum material condition, as the name suggests, is the condition when we have the maximum material for that feature. Now, let us assume a hole over here. For this hole, I give a dimension of 10 plus minus 1 mm. So, on which condition will I have the maximum material on the hole? Now, this hole can either be 9 mm or it can be 11 mm. And this hole is inside a plate over here. The maximum material of this hole. The maximum material of this hole will be when the diameter is the smallest, that is 9 mm. So, the MMC of a hole is always the smallest diameter, which is 9 mm in this case. Now, let us take a pin. For a pin, it is exactly the opposite for a hole. I have the maximum material on the pin when I have the maximum diameter of the pin.

For example, this pin. For example, this pin, let us call it a dimension of 10 plus minus 1 mm. The smallest diameter would be 9 mm and the largest diameter would be 11 mm. In this case, the MMC would be 11 mm. That is the largest diameter. Because at 11 mm, I have the maximum material on the pin. At 9 mm on the hole, I have the maximum material on the hole. Material is nothing but what is the part is made of. That is the metal, the part is made of.

So, if it is the hole, the smallest diameter is the maximum material condition. If it is the pin, the largest diameter is the maximum material condition. Let us take another example. Let us say I have another hole over here and I have found out the hole as 9.9 plus 0 and minus 0.5. Again, it is a hole. At what condition will I have the maximum amount of material on the hole? The maximum amount of material on the hole will be when I have the smallest diameter of the hole. What is the smallest diameter of this hole over here? It would be 9.9 minus 0.5, which is 9.4.

So, this is the maximum material condition for that hole. Again, let us take a pin over here. Let us say the pin is 10.5 plus 0 minus 0.5. Again, the maximum material condition is when I have the maximum material on that specific feature. In this case, since it is a pin, the maximum amount of material on that pin will be when the diameter is the maximum. In this case, it is 10.5 plus 0. So, 10.5 is the MMC of that specific feature. Now, the question arises, what is the difference between MMC and MMB? They mean the exact same thing. MMC and MMB means the exact same thing.

The only difference is where it is placed. So, if I have a feature control frame over here, let us say position of 1.0 M back to A, B, M and CM. And let us take an example. Let us say I have a plate over here. This hole over here. This another hole over here. And there is a third hole over here. So, A datum would be my surface. This surface would be called as A datum. Let us call this as my B datum. And let us call this my C datum.

And then I am putting a tolerance of 1.0 for this feature over here. So, when the M is placed on that specific feature, it is called as the MMC or the maximum material condition. If the M is placed on any datum, now this hole over here and this hole over here will have its own personal maximum material condition. When I put an M over here on the B datum or an M over here on the C datum, then that becomes my maximum material boundary. So, we will going to discuss more about maximum material boundary in the next segment where we will learn about what exactly a maximum material boundary means.

For this time, let us just understand that if the M is given to the specific feature, that is in this block over here, it is called the MMC. If the M is put on either of the datum, B, C or even A, but A is a surface, so we cannot put an M over here, but sometimes A is a pin or a hole. So, if an M is put on either a B datum or a C datum or any of the datum, then it is called as a maximum material boundary.

So, that is the difference between MMC and MMB. Technically, they mean the exact same thing. Maximum material boundary is when I have the maximum amount of material on the feature. For a pin, the maximum material condition or the maximum material boundary is when I have the highest diameter. For the hole, the maximum material condition or the maximum material boundary is when I have the smallest diameter. So, that is the difference between an MMC and MMB. Now, let us talk about LMC or LMB. That is the least material condition or the least material boundary.

So, LMC and LMB are exactly the opposite of MMC and MMB. LMC, like the name says, is the least material condition. That is the condition when I have the least amount of material on a hole or a pin or any feature. Similarly, least material boundary is the least amount of material on the boundary that I have on a hole or a pin or any feature. So, let us take an example. Let us take another hole over here. And I have, again, let us start with simple 10 plus minus 1 as the diameter.

So, the LMC, in this case, would be the condition where I have the least amount of material on this hole. In this case, the least amount of material on this hole I will have when I have the maximum diameter. So, the LMC would be 11 millimeter. So, assume that this hole is engraved in a plate over here. This hatching area is the material. On which condition when I will have the least amount of the hatching area or the material on this plate, I will have the least amount of material when I have the biggest hole, which in this case would be 11 millimeter.

Let us take another example of a pin over here. Again, this is very easy to understand. I will have the least amount of material on a pin where I will have the smallest pin. In this case, let us say the pin is 10 plus minus 1 millimeter of diameter. So, the LMC would be the smallest diameter. In this case, the LMC would be 9 millimeter. See how LMC works opposite to MMC. For example, MMC for a pin would be 11 millimeter. Then, I have the maximum amount of material on the pin.

Similarly, an MMC on the hole would be 9 millimeter. Then, I have the largest diameter on that hole. So, this is the difference between LMC and MMC. We are going to learn more about LMC, LMB, MMC and MMB in the next chapter when we will learn more about how datums behave. Now, RFS is nothing but regardless of feature size and RMB is nothing but regardless of material boundary. When, in certain cases, I don't have to call the feature by an LMC or MMC. In that case, I don't put any symbol in front of that dimension.

For example, if I have something called as a position 1.0 M back to APM and CM. In this case, I want the feature to be called out at the maximum material condition and I want the datums to be called out at the maximum material condition. At certain case, if I have something like this, in this case, I have not put any M symbol or L symbol over here. That is, I have not put any maximum material modifier, maximum material condition or least material modifier, least material condition on any of the feature or any of the D terms.

It means that I want those D terms to be called regardless of feature size. I don't want to call it back to an maximum material boundary or least material boundary. I want to call it to the features of size as it is. Now, let's talk about the diameter symbol phi. As the name suggests, phi is used anywhere where we use a diameter. For example, assume a plate over here and a hole is drilled inside that plate. I have to call out the diameter of that hole inside the plate.

I will just put a symbol phi 10 plus minus 1 millimeter. It means that the size or the diameter of this hole should lie anywhere between 9 to 11 millimeter. Now, this phi is also applicable to any pin. Let's say I have a pin over here and I have to call out the dimension of that pin. I will simply use the phi symbol and put my dimension 10 plus minus 1, which means that the diameter of this pin over here should lie anywhere between 9 to 11 millimeters.

Now, let's talk about a different kind of diameter known as spherical diameter or S phi. Previously, we learned about phi. The phi symbol is only applicable to a 2D hole. So, if I have a plane over here and then I have a hole drilled over here. In this case, I will call it as a phi. That is, it is applicable to any cylinder. But let's say I have a sphere over here. I have to call out the diameter of the sphere. In this case, I will use the symbol S phi.

It means that the spherical diameter of this sphere over here should lie, let's say, 10 plus minus 1 millimeter. It means that the spherical diameter of this sphere over here should lie anywhere between 9 to 11 millimeter. So, phi stands for a cylindrical hole or a pin and S phi stands for a sphere. Now, let's talk about projected tolerance zone. Again, let's take an example of a plate over here. And I have drilled a hole, a cylindrical hole inside the plate. I will give GDT a geometric tolerance to this plate.

Let's call it. Now, this is again a feature control frame. The first is the geometric characteristics. That is the position tolerance. Second one is the tolerance zone shape. In this case, it is a cylindrical hole. So, I have to put a phi. Let's put 0.25. Then back to A, B and C. What this means that the axis of the cylindrical hole should lie anywhere between a cylinder of 0.25 millimeter. So, the axis should lie within a cylinder of 0.25 millimeter. That is the position tolerance of that axis.

But this feature control frame only controls the axis for this width over here. That is the width of the plane. Let's say on a specific occurrence, I have to control the orientation axis, orientation of the axis, all the way till this point over here. And that point, so if this is my aditum over here, that point is let's say 100 millimeter from my aditum. So, I have to project this axis all the way to this point. In this case, I have to use the next symbol that is the projected tolerance P.

In this case, what I would do is, I would put a feature control frame something like this. Geometry characteristics, the tolerance zone shape, 0.25. Then I would have put a P over here. And then I would mention 100. And then back to A, B and C. What it means is that, I have to control the position and the orientation of this axis, not only for the thickness of the plate, but I have to control the orientation and position of the axis all the way to a point which is 100 millimeter from my aditum.

Now, any variation over here would be magnified all the way to this 100 millimeter point. So, I have to control that variation. That's why I put a P over here, which means that this 0.25 tolerance is applicable not only for the thickness of this plate, but it is applicable all the way to a point which is 100 millimeter from my aditum. Now, let's talk about the free state symbol, that is F. Free state symbol is nothing but it is the symbol that tells me that or I have to gauge that part when all the datums are in an unconstrained position.

That means, I don't have to clamp the part to the gauge. I just have to place the part in a gauge. This symbol is not used a lot in GD&T. It's more of useful for the gauge engineers or those who design the gauge. But, I have not seen any practical use of this free state symbol. Now, let's talk about the datum symbols. Datum symbols are nothing but symbols that represent a datum. So, let's say I have a surface over here, something like this, and I have to call this surface as a datum A.

In this case, what I will do is, I will just put the datum symbol over here and call this as a datum A. Datum symbol can be either perfectly perpendicular to the surface or I can also put something like this. This is for a surface. Let's say I have a feature of size. It means that I have either a hole or a pin or a tab or a slot. In this case, I have a hole of diameter 10 plus minus 1 and I have to call this out as a datum.

So, in this case, what I will do is, I will simply put the datum symbol over here somewhere on the leader line and call this out as a datum B. Or let's say I have a pin over here, 10 plus minus 1. I can also put the datum symbol over here, call this out as a c datum. So, this is nothing but a datum symbol. The second symbol over here, this, is not used currently in any of the GTNT drawing. So, we won't be discussing about it.

But it is similar to what we just discussed right now. Datum target, let's say I have a pin over here. The pin diameter is 10 millimeter and I have to call this surface of the pin as datum A. What I would do is, I would simply put a circle over here. So, whenever we have a datum called out at a surface, we generally use a surface rather than a point or an arrow. We generally use a circle over here, a thick circle. So, in this case, I would call this out as a datum A.

Let's say I have another pin over here. I have to call this out. I would call this out as a datum A2. A1 and A2 together will form my datum plane A. Sometimes, we have datum A as a line. In this case, what we do is simply point to that line and call it out as a datum A1 or A2. Sometimes, I have a datum target area. Let's say I have a big plate which looks something like this. Now, I don't want to call this entire surface as a datum.

I just want to call a small surface as a datum. So, what I would do is, I will draw a phantom line over here, hatch it and call it out as a datum A of 20. So, the difference between datum target over here is that we call that the first one as a pin. In this, this is the surface, but they both mean the same thing. So, we just point that entire thing to a surface over here, draw a circle of whatever the surface we want to be called as a datum A and we call it out as a datum A1 with a diameter of 20 millimeter.

Now, let's talk about movable datum targets. Let's assume that I have a cylindrical feature which looks like this over here and there are two engraved spears inside. Those are convex spears. To hold this part from both the side, I will link two full spears on each side. One over here, another over here. In this case, these two spears will become my A1 and A2 data. Now, these two spears are free to rotate around this center over here. That's why it's a movable datum target. And to denote it, what I would do is, I would draw this cylinder over here, draw a phantom line over here.

And this becomes my datum A1 with an S5 of whatever the diameter of this sphere is. Similarly, on the other side. That is how we denote a movable datum. Again, movable litem target is not a widely used concept. I still have to use a movable litem target in my book, but it's there in the GD&D. And now we'll talk about dimension origin. Dimensional origin is nothing but the origin of the dimension. Let's say I have a part which looks something like this, and this is my A litem over here.

So, the dimension origin would be from this side. So, the first one, let's say 22 millimeter, and then from here, it would be 20 millimeter. So, this point over here denotes the point of origin for the dimension. Now, let's talk about the different symbols used in GD&D, that is the geometric symbols. These symbols are very important. Out of these symbols, the most widely symbol is the flatness, then the perpendicularity, the position, and the profile of a surface. These are the four symbols that are highly used in GD&D.

So, in this segment, what we'll do is, we'll just try to understand what each symbol means, and try to get an overview of that symbol. So, let's talk about flatness. Flatness is nothing but it controls the flatness of the surface, as the name suggests. Flatness and straightness are pretty much similar, except that flatness is applied to an entire surface, while straightness is applied to a line. So, let's say, I have a model which looks something like this, and if I put a flatness on this surface of 0.1, what it means is that, this surface, entire surface, should lie within two parallel planes of 0.1 millimeter.

The width of the parallel planes should be 0.1 millimeter. So, this surface over here, this surface, will have some kind of waviness. So, that wave should lie within two parallel planes of 0.1 millimeter. Now, straightness is similar to flatness, except that, straightness is applied not to the entire surface, but just to a single line. Let's say, I have a single line called out over here, and I apply a flat, a straightness of 0.1 millimeter. It means that, this specific line should lie within two parallel surfaces, or two parallel lines of 0.1 millimeter across each other, and the wave should lie within those two parallel lines.

So, again, straightness and flatness are pretty much similar. Flatness is applied to an entire surface. Straightness is applied to one simple line. Now, let's talk about cylindricity and circularity. Again, cylindricity and circularity are pretty much similar to each other. So, let's say, I have a cylinder over here, and to this cylinder, I give a cylindricity of 0.1 millimeter. It means that, the entire surface of this cylinder, the entire outside surface of this cylinder, should lie within two parallel cylinders of 0.1 millimeter. Circularity is similar to cylindricity, but circularity is applied only to a single line.

So, let's say, I have one line over here, and I have to apply a circularity. In this case, circularity is applied only to this line, not to the entire surface. Perpendicularity. Perpendicularity controls the perpendicularity of that feature or the surface to datum A. So, let's say, I have a model which looks something like this. Let's call this as datum A. And I have to control the perpendicularity of this surface over here back to A, this 90 degree. So, what I would do is, I would put a perpendicularity on this surface over here.

Perpendicularity of 0.1 back to A. It means that, this specific surface should lie within two parallel planes of 0.1 millimeter, which are perpendicular to datum A. Parallelism. Parallelism is kind of opposite to perpendicularity. Perpendicularity controls the 90 degree angle. Parallelism controls the parallality. So, I have a datum A over here. Let's call this as datum A. I know this surface over here needs to be parallel to datum A. So, in this case, what I would do is, I will put a parallelism symbol of 0.1 millimeter.

It means that, this surface, the entire surface, should be parallel. So, what I would do is, I will create two planes over here, which are parallel to datum A. This surface over here, can lie anywhere between these two parallel planes, which are again parallel to datum A. So, this red surface over here, can either be oriented this way, or this way, or any way, as long as, it's, it's lying between two parallel planes, which are parallel to datum A. Angularity. Angularity, as the name suggests, controls the angle of the feature.

So, let's say, I have a feature, which looks something like this. This is my A datum over here. Let's say, this is 60 degree. So, when I give an angularity to this surface, an angularity of 0.3 back to A, what it would do is, it would again create two parallel surfaces, which lie within 0.3 range, millimeter range, and which are at an angle of 60 degree, nominally, to datum A. So, this surface over here, this surface, can lie anywhere between these two parallel planes, which are at an angle of 60 degree.

and the width of those two planes is 0.3 millimeter. Now, let's talk about position tolerance. This is one of the most important tolerances that I use in GD&T. We have a specific segment and a lecture for this type of tolerance. In this segment, we are just going to understand what it means. So, let's say, I have a plate over here. Let's say the bottom surface of this surface over here. The bottom surface is datum A. So, the surface is datum A. One of the hole is datum B.

Another hole is datum C. This is my C datum. This is my B datum. Let's say I have another hole. And I give a position tolerance of that hole over here, which looks something like this. 10 plus minus 1. I have to put a phi symbol over here. And then the feature control frame looks something like this. The first one is the geometric characteristics, which is basically the type of tolerance that we are using. I'm going to use a phi symbol here because it's a circle.

0.3 back to A, C. So, let's say I have to take a side view of this plate over here. In this side view, this hole over here would look something like this. It will look like a cylinder. So, when I say a position tolerance of 0.3 mm is applied to this cylinder, what I do is I actually apply that position tolerance to the axis of that cylinder. So, let's say this is the axis of the cylinder. It means that this axis of the cylinder over here for that feature can lie anywhere between a smaller cylinder which has a diameter of 0.3 mm.

So, this axis can lie either this way or this way or to the exactly side over here. It can lie anywhere within a smaller cylinder of 0.3 mm diameter. That is the meaning of position tolerance. Now, let's talk about profile of a surface. Profile of a surface is one of the most important tolerance used in GD&T. Profile of a surface and profile of a line are similar to each other except that as the name suggests profile of a surface is applied to the entire surface while profile of a line is applied only to a specific line.

So, let's take our usual example. So, the bottom surface of this surface the opposite surface of this surface over here is datum A. Let's call this hole as datum B and this hole as datum C. And then what I do is I give a profile to this surface with a feature control frame which looks something like this. Now, notice here I have not used a phi symbol over here because this is not a circular feature. This is just a surface. So, we don't need to put a phi over here before the tolerance over here before 1.0.

So, what this means is that this surface over here can lie anywhere between two parallel surfaces which kind of looks like this and the width of those two surfaces is 1.0 millimeter. So, the difference is profile can be used for any irregular surfaces. It can either be used to a straight surface or it can be used to an irregular surface. When we use a profile to an irregular surface, it means that I create two parallel planes of whatever the tolerances and that surface should lie within this range.

Profile is also applied to an irregular surface. So if I apply a profile to an irregular surface like this over here, the surface can lie anywhere between two surfaces which at each and every point are 1.0 mm apart from each other. Now, profile of a surface is applied to a line. Let's say I have a feature that looks something like this and this is a single line over here or rather the line kind of looks like this. So if I put a profile of a line to this line over here, it means that this line should lie within two parallel lines which at each and every point are 1.0 mm apart from each other.

So the difference between surface and line is that profile of a surface is applied to the entire surface over here. Profile of a line is only applied to a specific line over here. Now let's talk about total runout, circular runout, concentricity and symmetry. All these four tolerances again are hardly used in GD&T. Total runout and circular runout are mostly used in areas where there's a lot of cylindrical parts for example in medical industries. So total runout is nothing but it controls the outer surface of any cylinder.

Consider this example over here which I have pre-drawn. This cylindrical feature is my data A and I am putting a total runout on this smaller feature of 8 mm diameter for a total runout. What it means is that the surface of this cylinder, both the surface, so if I take a view from this side over here, it would mean to look something like this. What it means is that this surface over here, 8 mm surface should lie anywhere between two parallel cylinders which are 0.3 mm apart.

This is the meaning of total runout. The circular runout is similar to total runout except that total runout is applied to the entire surface over here, this surface over here, while circular runout is applied only to one specific circle, either this circle or this circle or this circle. That is the difference between total runout and circular runout. Now let's talk about concentricity. Assume I have the similar feature, two cylinders welded to each other at this point over here. My first feature of 10 mm, 10 plus minus 1 is my A data over here.

And then I have another feature which is 8 plus minus 1 mm. Now I have given a circularity, concentricity tolerance to this specific feature over here. What it means is that at any time, if I take a median of two opposite points, so let's say if I take this specific point over here, this specific point over here, and then I take this specific point over here, this specific point over here. There will always be a median point for these two points, let's call it this one and this one.

So this medium points of all these points over here, this median point, this median point of all the different median points for that feature should lie within a specific cylinder of 1.0 mm. So let's say I have one point over here, one point over here, and the median is over here. So this, the median of these two points, this point over here and this point over here should lie within a specific cylinder of 1 mm. That is the meaning of concentricity. Now let's talk about symmetry.

Symmetry is similar to concentricity except that concentricity is applied to circular features and symmetry is applied to rectangular or square features. So let's say this one feature and another feature are welded to each other. In this case, these are not circular features but they are rectangular features. So the distance between 2 is 18 plus minus 1 mm. I am going to call that as datum A. Since it is not a circular feature, I have not put a 5 in front of the 18. And then there is another feature over here, this one, which is kind of welded to my A datum.

In this case, what I'm going to do is, I am going to put a symmetry which will look something like this. So what this means is that if I take the median of, so this point over here, this point over here will have an opposite point over here. This point over here will have an opposite point over here. this point over here will have an opposite point over here. So, there would be infinite opposite points for this specific feature. What this means is that if I take the median of all these points over here, so let me kind of exaggerate it in here. So, the first point over here, the second point over here, third point over here, fourth point over here, fifth point and sixth point and then we have the medians of that point. What this means is that this median plane over here should lie between two parallel planes which are opposite to each other and have a thickness of 1.0 mm and those two planes are parallel to datum A plane which would be somewhere over here. This is the meaning of symmetry. Now, here is a small follow-up quiz for the segment that we just learned about. This assignment deals with all the symbols.

So, I have given a textual meaning of all the symbols over here. So, this, this, this are the text that represent the symbol. What I want to do is, I want you to write the symbol over here in this space. For example, a square symbol looks like this. Similarly, in the second quiz, I have the symbol noted down over here. And what I want you to do is, to write the name of the symbol and also the description of the symbol. so, I want you to write the symbol of the symbol of the symbol. And what I want you to do is, I want you to Thank you.

Want the rest of Geometric Dimensioning and Tolerancing?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Geometric Dimensioning and Tolerancing course

The remaining 61 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Geometric Dimensioning and Tolerancing course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.