Lesson finished
Up next: Reading Feature Control Frames and the ASME Y14.5 Standard
Unlock all 65 lessons of Geometric Dimensioning and TolerancingFull course ₹40,000 · paid
GD&T Benefits and Traditional Dimensioning Limits
A free lesson from Skill-Lync's Geometric Dimensioning and Tolerancing course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Introduction to GD&T”
What will you learn in this free Geometric Dimensioning and Tolerancing lesson?
The instructor introduces GD&T as a way to dimension and tolerance a part for function and assembly, using the four phases of part development as context. It covers dimensional variation and gap analysis, then compares plus-minus tolerancing with GD&T using a flatness example on a table top.
- Four phases of part development where GD&T is used
- Why GD&T controls variation and supports gap analysis
- Limits of plus-minus tolerancing on form and orientation
- How a flatness tolerance controls surface waviness
What comes after lesson 1?
The next free lesson is lesson 2, “Reading Feature Control Frames and the ASME Y14.5 Standard” (24 min). Later in Skill-Lync's Geometric Dimensioning and Tolerancing course (paid): lesson 4, GD&T Lecture 2 - Segment 1; lesson 5, Understanding Form Tolerances in GD&T; lesson 6, Understanding MMC and LMC Conditions in GD&T. The full course has 65 lessons (13 h 6 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Hello everyone. Hope everyone is doing fine today. Welcome to my lecture series on GD&T. This is an introduction to GD&T. We'll talk about the various aspects of GD&T or geometric dimensioning and tolerancing. This lecture series I have divided into various segments. So let's start with the first segment. The first segment is the introduction to GD&T. In this segment we'll talk about the benefits of GD&T and then we will compare the difference between a traditional dimensioning and a geometric dimensioning and a geometric dimensioning. tolerancing. But before we go ahead, let's talk about the development process of any mechanical part in industry. Any mechanical part in industry goes through four different phases. The first one is the design of the part where we use the CAD softwares or CAE softwares. Then we develop the tool for the part. Then we actually produce the part and then we inspect the part. In all these four phases GD&T is used as GD&T is so widely popular. So GD&T is nothing but a way to dimension and tolerance the part in which we consider function as well as the assembly process of the part. So let's talk about the significance of GD&T. Why GD&T is so significant in automobile industry or in any manufacturing industry? The first significance of GD&T is that it is used to control the dimensional variation of any parts.
Let's talk about GD&T. Let's talk about my company Jeep. Every year we produce about 80 to 90,000 Jeeps. Thus I have to make sure that each and every part that I make or I design has to be similar in shape and size to the previous parts. How do I make sure that each and every part is exactly the same or it lies between some tolerance range compared to the previous part? This is where GD&T comes into place. Second significance of GD&T is to perform gap analysis. Now any two parts that go on to a third part. Let's say there are two body panels that go on to the body frame. There is some gap between these two body panels and I have to measure this gap.
To do that GD&T is used. Now there are various methods to do the gap analysis. One is the RSS that is a root sum square. It's a one dimension process. And then there is a software called 3DCS which takes into account a 3D gap. With GD&T we can define the locating scheme of the part. Since the parts are interchangeable and the variation is less, GD&T saves money. There is also a concept called as Bonus Tolerance which we will learn later which is very appreciated by all the suppliers and it saves a lot of money for the suppliers.
GD&T is a universal language of symbols. So even if I am sitting here in the United States there is another engineer in Germany and there is another engineer in India. We all are able to communicate regarding the design of the part with GD&T and we understand each other exactly because of GD&T. And finally who controls GD&T? GD&T is controlled by an association called ASME or American Society of Mechanical Engineers. What they do is every 10-15 years they will come up with a new set of rules for GD&T and as a dimensional engineer we have to make sure that we learn those new rules and apply it to our process.
Now let's talk about the history of GD&T. Is GD&T just a latest fad? No, GD&T has a significant amount of history to it. While there is no paper trail that attributes GD&T to a specific person, it is generally assumed that engineer named Stanley Parker who was working in the Royal Torpedo Factory in Alexandria, Scotland is the inventor of GD&T. GD&T. What he came up with is a process called as true position or nowadays we call it as a position tolerance. So he defined a process to measure the axis of the hole of any part and thus the true position concept came into existence.
This true position then gave a way to profile, flatness, perpendicularity and so many other tolerances. Fun fact, there are 14 different tolerances used in GD&T. After the World War II when there was a manufacturing boom especially in automobile industry, GD&T was used on a very vast scale in military and then big companies like Ford, Chrysler, GM started using GD&T in their process. So let's talk about the types of dimensioning. Now dimensioning is generally categorized into three different parts. The first is the general dimensioning which we have been learning all the way across our education.
The second one is the geometric dimensioning which is GD&T and the third one which is not so popular is surface texture. Surface texture is nothing but how we define the surface of any part. It is more of a visual rather than a functional aspect of the part. So this is the traditional dimensioning. In traditional dimensioning we go by two routes. In one route we just give the dimension of to the part. For example here 16 mm is the thickness of this part over here. 14 mm is the diameter of the hole over here. At 120 degrees is the angle over here.
Now you know that no process in the world is so advanced that each and every part produced is exactly to its nominal. For example let's say I have to produce this first part over here and I have to maintain the thickness to be 16 mm. Now there would be some parts which will have 16.1 mm thickness. Some part which will have 15.9 mm of thickness. There is no way I can hit exact this golden number 16 in all the parts. So I have to give some kind of tolerancing.
So this is the second way to go with traditional dimensioning. What we do is we give some kind of tolerances. For example in the first section over here the tolerance is 40 plus minus 0.1 which means that the length of this section over here can lie between 40.1 to 39.9. In this way we give some tolerance to the manufacturer. However even we give the tolerances this type of dimensioning does not control the orientation or form of the part. For example this first segment over here the second segment over here this third segment over here even though they have they may lie between the tolerances that we have given there is no way to control the part in geometric way.
For example there is no way that this axis over here this axis over here is perfectly parallel to this axis over here or it's perfectly parallel to this axis over here or perfectly parallel to this axis over here. This type of traditional dimensioning does not take into account the geometry, does not take into account geometry or the form of the part. That's why I have to make let's say 10,000 or 20,000 parts. This type of dimensioning is useless for me. Let's take another example over here.
Assume that I have to make a pin of a diameter 10 plus minus 1 millimeter. I want this pin to be perfectly perpendicular to this plane over here. However, on a very bad day, the operator will create pins which has an angle to my plate over here. Now, in traditional dimensioning, what I would do is I would just say 10 plus minus 1 diameter of the pin. That means the pin can lie anywhere between 9 to 11 millimeter. So, bad day, the operator makes a pin something like this.
The inspector or the person who inspects the part puts a point over here, point over here and it comes to be let's say 9.9. Is this between the range 9 to 11? It is. So, what the inspector would do is it will approve the part. However, as a CAD engineer or as a design engineer, is this the part that I really wanted? No. What I really wanted is that this axis to be perfectly perpendicular to the plate which the traditional dimensioning fails to do so. Hence, we have something called geometric dimensioning and tolerancing.
Let's take another example over here. This is a simple table that I want to develop. Now, in traditional dimensioning, what I would do is I would give the height of the table to be 27 plus minus 1 millimeters. So, it would the height of the table from one end to the other can lie anywhere between 26 to 28 millimeter. So, on a very bad day, what the operator would do is he would create something like a slanting table over here as you can see in this picture.
Now, this is a slanting table and the inspector or the person who checks or inspects the table, he would touch one point over here all the way to the ground. So, this point over here all the way to the ground, it will come to be 28 millimeter. Then, he will check another point over here all the way to the ground. It will come to be 27 millimeter. And then, the last point over here all the way to the ground, it will come to be 26 millimeter.
Does this lie within my range? It lies, yes, 26 to 28 millimeter and then the inspector will approve the table. Another thing is that there is no way with the traditional dimensioning, I can control the waviness of the surface. Now, any surface, if you consider, has some kind. So, if I say the surface is plane something like this, in reality, the surface would be like this. It will have some ups and downs, some valleys, some hills, right? And in traditional GD&T, there is no way I can control the waviness of the surface like mentioned over here. Hence, GD&T comes into play.
Now, the same table with GD&T, what I can do is I can just apply something called as a flatness tolerance on the top of the surface. So, what it means is that the height of the table can lie anywhere between 26 to 28 mm. That's fine. However, the waviness of the surface, that is the ups and downs of the surface should lie within two parallel planes. that are within 0.06 inches. In this case, it's inches, not millimeters. So, thus, I control the waviness of the surface over here. So, I cannot have something like this.
Is this allowed? Is this allowed? No, because I am specifically telling the operator that yes, you can have some waviness of the surface, but it should lie within two parallel planes of 0.06 inches. So, thus, we see that GD&T definitely defines the part more accurately to the operator. There are no confusions between the operator and the inspector. So, thus, as a CAD engineer, if I apply GD&T to any part, I am pretty sure that I will get the part exactly as I intended for the design.
So, having said that, I have a simple quiz for you guys. You can go through these questions over here. You can find the answers to this question online. And this will kind of give you an idea or kind of act like an assignment for you for the first segment.