← Previous lessonFree lesson 2 of 3 · lesson 2 of 45Next lesson →

Unlock all 45 lessons of Design of Bridge Substructures / Piers using STAAD.ProFull course ₹40,000 · paid

Price & syllabus
Free lesson · 29 min · no payment

Parts of a Bridge, Design Codes, Concrete and Steel Grades

A free lesson from Skill-Lync's Design of Bridge Substructures / Piers using STAAD.Pro course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Parts of a Typical Bridge”

What will you learn in this free Design of Bridge Substructures / Piers using STAAD.Pro lesson?

The instructor divides a bridge into superstructure, substructure and foundation, with bearings between the first two, and explains why design runs top down while construction runs bottom up. The lesson lists IRC, IRS, IS, Eurocode and AASHTO codes, minimum concrete and steel grades by exposure, clear cover, and how loads reach the ground through end bearing and friction piles.

  • Superstructure, substructure, foundation and bearings
  • Design order versus construction order
  • Roles of IRC, IRS, IS and Eurocodes
  • End bearing and friction pile load paths

What comes after lesson 2?

The next free lesson is lesson 3, “Bridge Loads and IRC 6 Load Combination Factors” (21 min). Later in Skill-Lync's Design of Bridge Substructures / Piers using STAAD.Pro course (paid): lesson 4, Introduction to Bearings in Bridge Engineering; lesson 5, Articulation of Bearings in Bridge Modeling; lesson 6, Introduction to Bridge Abutments and Types. The full course has 45 lessons (20 h 54 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Moving next to parts of a typical bridge here in this section we will try to cover the different parts a typical bridge consists of. Generally in case if you haven't gone through this earlier it will be will go in detail but if you already gone through these different parts of a bridge then we will do a quick recap. Typical bridge consists of mainly three parts that is a superstructure, substructure and foundation. If you look at to the top right picture you can see here a superstructure is from a superstructure can also be called as a deck DECK yes a superstructure can be generally referred to as a deck.

If you look into this picture at the top right here the portion which is above the blue color beam girder here it is called superstructure and this and above you can see a parapet or railing also that also comes under superstructure. And our next will be substructure if you look into it that part of a bridge at least in this bridge the part which is above this foundation this is called pile cap here in this arrangement the structure which is above the top of pile cap till the superstructure at this point it is called as a substructure.

So this substructure will also includes the abutment which is at the ends here and the wing wall which will be connected to abutment. So substructure includes those two also and the intermediate piers and the next one would be a foundation that is below top of pile cap whatever structures are there they are considered as a foundation in this picture here. One part which is not specifically mentioned here is bearing here which is in between the superstructure and substructure the part which transfers load from superstructure to substructure that is called bearing.

If you look into this picture here if you look into this picture here you can see the highlight I mean the encircled here the red this is called a bearing and this is just a rough diagram of or not right this is just foundation wherein you can see the bars are already laid and they are in place. So this is a foundation here and if you look into this picture you can see these are substructure superstructure. So that's all about the parts of a typical bridge so generally any bridge can be classified into these three parts that is superstructure, substructure and foundation.

Moving on so as I mentioned the superstructure not just only consists the parapet or the railing or the crash barrier in addition it will also has footpath. Generally for pedestrians because on the carriageway only the vehicles are allowed to move so what if pedestrians want to use that bridge. So for that purpose you will have a special provision so that there will be a footpath for pedestrians. In this picture you can see there is a track also most of the countries now everybody wants to be more sustainable and better greener earth.

So now there are bicycle tracks which are also being led side of the carriageway so this particular bridge either it can be used as a footpath and as a bicycle track as well. And surface course you can see the one on the carriageway in this picture you can see the black here and in this picture here also the black part which is basically either of a bituminous or it can be any material. Okay so the part that is referred to as a surface course so these are all parts of a superstructure.

Now let's have one more brainstorming time. Whenever we construct a bridge what is the process? First we will start with the foundation whatever structures which is proposed for foundation. So we will begin with it once we complete the foundation we will move to the substructure. Once the substructure is finished or is constructed then we will move to the superstructure. Generally this is what the practice during construction. But is it the same while designing? While designing the bridge are we going to follow the same process? No because while designing we consider I mean we transfer the loads from superstructure first.

What are the loads that act on the superstructure then we will transfer those loads to the substructure and from substructure to the foundation. So unless we have a load definitely a load value on superstructure or on substructure we cannot design itself. So basically when it comes to design first we will design the superstructure after designing it or after analyzing it only we will understand how much load is being needs to be transferred to the substructure. So first we will design superstructure and then substructure and then foundation.

So this is how the process differs when compared to construction. I think that's all for this brainstorming session. So let's move on to next. Bridge design codes. Different countries have come up with their codes which are used for a design based on their local requirement. So generally there will be some factors which correspond to that particular local region. Though the concept may remain same but there will be some additional factors which correspond to any local region. So that's how so that is the reason we have so many codes for we have codes for each countries.

Else we could have just have one code and the same code could be used throughout the world. But it is not so because the local conditions differ as the country from country to country. So in India we have IRC, Indian Road Congress. Those that is specifically for highway bridges or for flyovers. Those things we generally refer to IRC. Then we have IS, Indian Standard. Then we go for buildings, right? Even in our bachelor's degree we have used IS for designing various component structures, right? For building design, for beam slab design.

We have used IS code. Similarly, IRS in India we generally use for Indian Railway specification. Those Indian Railways has come up with its own code because of the importance it carries, right? So we know Indian IRS has Indian Railways as a large connectivity and it is a very vital. So that's why it has come up with its own code. And similarly, Europe has EN series. Euro code 1, 2, 3, 4, it has different series based on the building or materials or based on whether it's a bridge.

So Europe has different series. And America has ACI, American Concrete Institute codes for concrete and other materials. Similarly, it has AASHTO for highways. So different countries have different codes. Why do we have these codes? Are they really required? So what is the significance of these codes? These codes when published, they are generally meant to provide a guidance, confidence and assurance to the designer as well as the clients and as well as the users. So we generally, there is a good probability that there can be a general argument that a person can feel that his or her design would be safer for a given condition.

But there will be other person who doesn't agree with that. So these codes during that time, these serve as a guidance or they provide confidence. Suppose if we design a structure as per this code, it will, it will there as long as it is intended life is there. So till that it would survive. So basically, these codes, before they are published, there will be a lot of experiments and practices based on the long many years, so many years. Based on that, we would have arrived with that code clauses.

So that's what gives confidence to us, at least for designer. Can we deviate from this code? What if I don't agree with, if I don't design the structure as per that particular clause of the code? Can I do that? Is it allowed? These codes are basically there for set as a guideline. So there is a good probability that it may not cover all the aspects of a design and execution of a particular structure. So generally, there may be, there will be loopholes and there will be a reason for benefit of doubt.

So during that time, we can deviate from the code if we have a proper reason and if we have proper backup on why we are devoting from the code, we can deviate. There are many instances in the, at least as far as the design is concerned. There are many instances wherein a design team deviates from the code because of non-availability or there is not a clear definition on a particular clock. So there are instances where people deviated from the code but with a proper background and reasons and research.

So for bridge design in India, we are referring these codes which are listed here. So IRC-5 here in this it generally features of what general features on design of bridge are mentioned in IRC-5 and we do refer IRC-5 when we need to have some guidelines on how water needs to be considered or water effect needs to be considered on the bridge. During that time also we refer IRC-5 and IRC-6 which basically deals with the various loads that act on the bridge and the various load combinations.

We will touch these loads and load combinations in the subsequent slides as per IRC-6 and then we have IRC-78 which mainly deals with foundations and substructures. So there are clauses in IRC-7 which correspond to various foundations and the soil as well and how the soil parameters yeah based on it deals with that and IRC-83 we have part 1 to part 4 which involves guidelines for bearings maybe different types of bearings. What are the types of bearings and more on bearings we will touch in the subsequent slides and IRC-112 this is specifically for concrete road bridges it will cover all the guidelines or the guidelines need to be which need to be followed while designing a concrete road bridge.

Similarly IRS CBC this is for trial specifications which is CBC stands for concrete bridge code it deals it gives guidelines on concrete bridge. Similarly we have as I mentioned earlier euro code you can see EN 1990 euro code 0 which is also called it basically deals with the structural basis of structural design. How this on what basis we are going to perform the design so that's I mean it will give some clauses on it and 1991 it deals with what are the various actions that occur on a structure.

These actions can be various loads or because of some other what are the various forces that act on structures and 1992 part 2 it deals with reinforced design and precessed concrete also. For bridges for bridges specifically and 1993 is for steel bridges and 1994 is for composite steel iron concrete so composite bridges basically we have separate code in 1995 which deals with the timber bridges so timber constructions are more in Europe compared to India because it may be of availability reasons so we have a separate code on for timber structure.

For timber structure bridges though I am in 1998 it is for earthquake resistance structure design how we design earthquake resistant bridges we are not going to design earthquake proof it would be absurd but we will be guide will be having a guidelines on how to design earthquake resistant bridges so that's all about various bridge codes. Now coming to the grades of concrete and steel which we use in bridges so as per Indian driver standards we have in the first table if we look into it we can see here for bridges increased concrete and if the bridges are considered as important so IRS tells that if the member is a PCC member supply and cement concrete member then for moderate exposure.

If we look into the code if we look into the code there will be exposure conditions so there are clauses which say when we when we can call an exposure as a moderate or when we can call the exposing conditions as a severe or extreme based on that we put I mean the code has put a cap that the minimum grade for such member in such condition needs to be here. So generally for RCC member we consider moderate exposure we will say the minimum should be M30 that should be the grade of concrete.

So we have some other here so we have some other here in at least for bridges other than mentioned about substructure you can see here a PCC member can be of 15 grade concrete also for moderate condition. And you can see here when it's when it's when we call a condition as a moderate severe here in the code it's given definition as if a concrete if a if a if a exposed condition needs to be called as a moderate then the concrete needs to be protected against I mean that concrete would be protest would be protected against aggressive conditions or it from severe rain or freezing walls.

So if our concrete is not exposed to that then we can call it as a moderate for severe we can see if our concrete is exposed to aggressive subsoil or groundwater or if it is located in a coastal environment then we can consider it as a severe if it's extreme then you can see the concrete is just I mean you can see a seawater spray can occur on that concrete which leads to corrosive beams or severe freezing conditions. So if in that conditions we can call it as an extreme environment again from IRC code there is some how the if you look into the left table here these are the various grades of steel recommended by IRC the minimum is FE415.

So earlier we had in our bridges we had in our bridges we had used FE250 also but now that the minimum has set to FE415 and it starts from there and then FE415D which is nothing but deformed and it goes till 600 FE600. Similarly in IRC we have for different exposure conditions what is the minimum grade of concrete to be used that is the one guidelines in IRC code. So again just a small small inserts from a code in major bridge let's say if you are going to pile foundation then in major bridges especially then the grade of concrete should not be less than 35 MPA.

For pile cap also it's 35 and if you come to PR it increases now at least there are a PR which goes to M50 so depending again it depends upon stresses. For PR cap also we need to take 50 MPA as a minimum grade of concrete. Next for superstructure we can form M45 to M55 again depending upon design design in the sense whether are we going to use a simple RC beam bridge or it is going to be a pre-stressed concrete bridge. So based on that again the grades needs to be considered and steel grade steel reinforcement we need to include at least FE500D grade and that steel grade needs to be conformed as per IS 1786 and clause 4.5 and 7.1.5 of IRS CBC shall be used.

So this particular grade it is taken from IRS so that's why it is given a reference as IRS and steel strands. When do these strands come into picture? These strands are nothing but our pre-stressed concrete cables which we use in pre-stressed they are made up of the steel strands. So we have a great limit on those as well so here it is spelling that those strands should have a minimum breaking stress of 1862 MPA. Again a few more screenshots from IRS bridge code. A clear cover if you look into the clear cover again we have some definitions saw some guidelines on what's the minimum clear cover.

So before that let's know what exactly they mean when they say clear cover. It is the least distance from outermost surface of steel to the end of the face of the concrete. So that is called as a clear cover and if you look into this table here if the type of structure based on a type of structure and environment conditions there is a cap on a clear cover. If we for slab if you are designing a slab bridge for extreme minimum clear cover needs to be 50 MPA and it goes on for moderate as well.

So for beam it's called let's say for moderate we need to have a 35 mm all your millimeters you need to have 35 mm as a clear cover. Again we have some guidelines on crack width. So if you look again based on the exposure conditions so you can see why exposure conditions are very important to know here because based on the exposure conditions there are many factors in the design which are governed by the exposure conditions. If you look into here even the concrete cover is controlled by the exposure condition.

If you look into here even the crack width is governed by the exposure condition. So next we will have some uh uh uh You'll see some bridge collapses. Before that, why does the bridge collapse? We have so many guidelines. We have so many precautions. We take so many precautions while designing, while construction, but still many bridges do collapse. What are the main reasons? I mean, why are there, why the bridges are being collapsed? At least in India, why are, what's the reason? Right? These bridges, because of various factors, because maybe a error while designing or a poor quality, construction method, or because of some, what do you call, because of some, because of earthquakes, volcano, whatever, maybe reason, because of some reason, natural calamities. Because of that also, the bridge can be collapsed. You can see the picture on the left here. You can see it's a mini-police bridge collapse. Why are we looking at these pictures? What is the reason for me putting these pictures here? When the collapse occurs, it is definitely, it is definitely, it will definitely cause a catastrophe. It will be a catastrophic event. You can see in the picture there that there are so many cars. I mean, you can just, you can't just imagine what the situation there would be. It would be definitely a catastrophe when a bridge collapse.

So, it is very important. It is necessary for us to take all the precautions while designing as well as while constructing a bridge. And again, we have this Mississippi bridge collapse on the right as well. See, we can, all you can see is just, uh, look into here. Next, we have a superstructure collapse down there. And in the right picture, this is not at collapse, but you can look into the bottom. I mean, the, the part just above the water here, it has just left. So, it is bound to fall. It's bound to collapse now. So, these are the various, just a small glimpse on the bridge collapses. Because when the bridge collapse, there will be a huge loss in terms of people's lives, resources, and the property also.

So, at any cost, we should not give a chance for a bridge to collapse because of our errors in a design or in the poor quality in construction. Next, coming to various loads, the loads that actually act on the bridges. These, the various loads that act on the bridges are covered in a separate course. So, you can refer to the course design loads considered on bridges. So, if you refer to there, you can learn a great deal about the various loads there. So, I am not going to discuss in detail about the loads that act on the bridges. You can refer to this particular course.

But, we will discuss how this load will be transferred from top, that is, from superstructure to the ground. The main reason we do, we spend so much of time and energy on bridge design is, the ultimate purpose is, whatever load that act on the top, it should be safely transferred to the ground. That is the main part. You can look into the left picture here. This is a typical arrangement in, let's say, it's arrangement of beam column and foundation. Generally, what we see in the buildings, let's say this is a slab and on this slab there is a load.

So, there is a vertical load acting on the slab here and this load, let's say, if we act at the center of the slab here, then that load will be transferred in all the available directions. We have beams below that slab. So, that load will be transferred to the beams below and from that beam, it will be transferred to this particular beam which is connected to these beams. From this beam, it will be transferred to the column. Again, from column to the foundation. This is a typical load transfer mechanism in buildings. Let's see how these loads are transferred in this particular structure here.

You can see the blue things here. That is the load, the load, this load. You can see, this is, if the superstructure is this fashion, whatever load will be transferred to this and there will be overlapping here, this part here. Again, it gets transferred to here. Again, it gets transferred to below. I think it's a piles here. This particular picture, it gives how the load transfer occurs when the foundation, here the foundation is a pile foundation. If the pile foundations are situated or taken till the bedrock, how the loads will be transferred. And if the pile foundation is above the bedrock, is above the rock, basically it's just terminated in the soil.

If that is the case, if that is the case, then how the load transfers occur. In the left picture, if you see here, the entire load from here to the bottom and it gets dissipated at the rock itself. There is no transfer in the soil. There is no transfer in the soil here for this arrangement. But if you look into the, this set of piles, which are called friction piles, because they transferred the load with respect to friction. Using the friction, they transferred the load. So there is a friction of soil from this point to this point. And the load transfers to the soil with this friction.

So here, the load is shared by soil over the length of the pile. But here, there is no that activity because all load will be transferred directly to the bedrock. So generally, this is generally in bridges, we go to pile foundation whenever the soil, the founding soil is inadequate to transfer that much load or there is a requirement such that maybe, maybe generally if there is a water body, we, I mean, generally the soil near the water body is not, will not be enough. I mean, a general normal footing or generally a surface is not enough to carry that much load.

So generally, we go to the pile foundation in bridges. And again, pile foundation, we have two types here. That is the one which takes the pile directly to the bedrock. It is called end bearing piles. For the one which is, which terminates in the soil itself, it is called a friction pile. So having seen how the load transfers in the structure from superstructure to the ground, then we can, let's see how this load transfer occurs in this particular bridge. If you could recall, if you could recall the picture earlier, then you can see it is a cable arrangement. So what type of cable arrangement? So what do we call this?

Whether is it a suspension bridge or it's a cable state bridge? So in the earlier, I mentioned that a bridge will be called a cable state bridge or a suspension bridge based on the way the load is transferred. So this is, this transfer mechanism corresponds to suspension bridge here. If you look closely, there is a cable here and these are the generally steel elements which are directly tied to the deck. So whatever load that is applied on this deck will be transferred to this steel elements or whatever material they use, that element to this cable and it will be transferred to the end here.

It's abutment. Similarly, the load also transfers in other direction. And again, it might reach to pile on here and it can transfer down to the ground. Similarly, if the load is acting at this point here, you can see the load is transferred in this direction through cable as well and this direction also. And again, all that all load will be distributed among these various connectors here. So this is how typically load transfer occurs in suspension bridges. Now coming to arch bridges, the red color, it is generally called a keystone. It's also called a crown, which basically is the most important part of a arch structure.

So here when you apply load on this, you can see how it is transferred to the sides here. When you apply load here, it will be transferred in this fashion here. And if we have support here, again, we will have a horizontal reaction here. That's, this is how the loads get transferred in arch bridges. Now we saw how this load transfer occurs in a bridge on different types of bridges actually. Based on that, we can design our bridges using that transfer mechanism. Now moving on to various loads. We don't, we won't go much in detail here.

Want the rest of Design of Bridge Substructures / Piers using STAAD.Pro?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Design of Bridge Substructures / Piers using STAAD.Pro course

The remaining 42 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Design of Bridge Substructures / Piers using STAAD.Pro course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.