← Course overviewFree lesson 1 of 3 · lesson 1 of 45Next lesson →

Unlock all 45 lessons of Design of Bridge Substructures / Piers using STAAD.ProFull course ₹40,000 · paid

Price & syllabus
Free lesson · 28 min · no payment

Bridge Structure Types and How Bridges Are Classified

A free lesson from Skill-Lync's Design of Bridge Substructures / Piers using STAAD.Pro course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Design of Substructures”

What will you learn in this free Design of Bridge Substructures / Piers using STAAD.Pro lesson?

The instructor explains why bridges are built and what bridge engineering covers, then describes truss, cable, arch and portal frame structures and why each behaves as it does. The lesson classifies bridges by material, length, form, function, road level, navigation clearance, service and degree of redundancy, and previews STAAD.Pro modelling in later weeks.

  • Truss, cable, arch and portal frame behaviour
  • Classifying bridges by material, length and form
  • High level versus submersible bridges
  • Statically determinate and indeterminate bridges

What comes after lesson 1?

The next free lesson is lesson 2, “Parts of a Bridge, Design Codes, Concrete and Steel Grades” (29 min). Later in Skill-Lync's Design of Bridge Substructures / Piers using STAAD.Pro course (paid): lesson 4, Introduction to Bearings in Bridge Engineering; lesson 5, Articulation of Bearings in Bridge Modeling; lesson 6, Introduction to Bridge Abutments and Types. The full course has 45 lessons (20 h 54 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Welcome to the course on design of substructures of peers. In this course, we will, we have tried to touch and learn what are the most important aspects of substructure and during the period of courses, we also try to highlight how people in industries think before designing the substructure or what are the factors would be considered while designing the substructure. We also try to impart the knowledge of industrial practitioner also so that it would give a better picture on how the actual design of substructure occurs compared to just a theoretical knowledge from the books.

Hope you will enjoy this course. So let's begin our course. The first week, we will, it is very important to understand the bridges before we dive into substructures, right? So let's begin with understanding the bridges in the first week. In this week, we will try to cover introduction on bridges and what are the basic structures which are involved in a bridges from a structural point of view and then we will also try to know more about how bridges are classified and what are the parts of a typical bridge.

What are the various design codes which are used? We will be concentrating more on Indian codes and what are the various grades of concrete and steel which are used in general bridge construction and we will have a quick slides on the various collapses between the bridge collapses occurred in the world, throughout the world and the signifying the need for maintaining quality and proper knowledge while designing the bridges. We will also touch about the various loads. We will also touch about the various loads that act on a typical bridge and then how these loads are combined to produce a more onerous effect on the structure after that we will touch bearings which can be combined with substructure.

So what is the part of what is the part of what are the what is the part of the bearings in transferring loads and what are the significance and the characteristics and types of bearings we will discuss over the course we next basically we will be learning about in this course about the structure elements in a bridge the significance of bridges different types and classification of bridges and various materials used in the bridges and was a necessity for the proper design construction in a bridge. And we will also touch the bridge codes and combinations and also a small glimpse on the different grades used in the concrete and steel and you will be learning a detailed or more details on bearings.

The prerequisite for this course is we should be aware on the various loads of actually the more detailed information on loads of bridges is required and how these loads are combined as per Indian standard. Basically these two are prerequisites when we go for modeling in STAT Pro and analyzing basically when we apply loads and load combinations during that time these prerequisites are necessary. So let's begin then. Before we start it is I would just like to highlight that if we ignore the water under the bridge then we will definitely find our bridge under that water.

This is one of the famous sayings I don't know the source of it but this definitely is the one of the most important aspect before we start any bridge design. Move on. Introduction. Before we start introduction we need to understand why there is a need for bridge. Why we construct bridge. Are they really required? Bridges. Because generally these bridges are not available where the human beings want to use it for basically there will be a separate places or maybe the connectivity issues between two lines. So we cannot connect those two lines with other the help of other modes.

So then there would be a need for bridge and most of the times we may not be able to connect isolated places because of some valleys or because of some water bodies or because of congestion in cities. Yeah. During that time we need a bridge to be constructed to connect those places. What exactly a bridge engineering involves? Firstly it involves a plan a properly laid out plan on how and what are the things and where and how to effectively use the different materials. This knowledge is very necessary and once we have a complete knowledge on this we can start a design.

So we will have a proper set out on how we are going to design the various components of the bridge and then not designing is not sufficient unless the same thing can be executed during the construction. And once the construction is over it is the most important would be the maintenance of a bridge. Just the constructing isn't sufficient. Most of the bridges if we look in today's world if they are not maintained properly within a few years they would be not in a state to use them.

Generally when a bridge is designed generally it would be designed for 100 years or 120 years. But can we if you look into today's construction the way the construction is being carried out in many countries we may not agree that that particular bridge can survive for 100 to 120 years. So these all aspects the plan design construction maintenance of a bridge together we can call it as a bridge engineering. And other than that our bridge engineering also involves that the bridge which is constructed should have adequate strength and it should be safe for the people or the living or for the animals or whatever purpose it has been designed and executed for that it should be safe as well.

And a bridge engineering also involves that the bridge which is constructed will help in effective transportation of people as well as vehicles. We can think of rails and the corridors especially which generally carry more number of vehicles. So they also come under bridge engineering. And nowadays just the above three are not sufficient. Now it is more important that the bridge needs to be more sustainable. It's not just if it is if it can carry the people and the vehicles and if the strength of the bridge and it is safe is not that much.

We if we want now sustainable as a part of a bridge engineering wherein our bridges are more sustainable. What are the common structures we see in our bridges? We might have been walked generally when we walk into the city or wherever where bridges are constructed. So what are the common structures we see in those bridges? Generally the trusses especially if we have often walked on the foot bridge or if you have seen any number of foot bridges. Trusses or truss structure is the common one which we generally use in foot bridges.

And the picture shown here that's a type of truss at least in Indian railways we see whenever we cross any river. That's a type of truss bridge we see in India at least. So what exactly are these trusses? It is a triangulated system of members. Members here in the sense the various steel you can see the N-shaped or the angular or the channel sections. Whatever these members they are structured in a triangulated system and connected effectively or efficiently so that only axial force will be induced in those members.

There will be no bending. There will be no shear force in those members but purely axial force. So why triangular? Why not some other shapes? That is because triangle is a mathematical. Mathematically triangle is a most stable configuration. So these trusses can be arranged in such a way that we have struts and ties. So there will be we will try to touch struts and ties in the future course. As the course proceeds we will try to touch what exactly are the struts and ties in that.

And how these forces are transferred in trusses? If we observe the behavior of these trusses, generally the force, the axial force will transfer from one member to other member through compression and tension. When one member tries to compress and it will be inducing tension or the compression to the adjacent member. So that's how the force gets transferred in trusses. So trusses are basically they will be having only two forces in them. Either it would be a compression or tension or nothing that is zero force. So basically the two forces would be either it's a compressive force or tensile force.

Next. Basically these are generally used in bridge designs as I said earlier because why we are using trusses? Why not other structures? So they have proven to be more efficient in span long distance. I mean, when the span is more, I mean, they have proved to be more efficient if you use trusses compared to other structures. That's why they have wide uses earlier. In trusses, generally, if you look into the nodes, I mean, how are we achieving just an axial force in the truss? That is just a compressive or tensile force. How can we make sure that only these forces, the compressive or tensile exist in the truss?

This is achieved by making the nodes of a truss, the joints as pin joints. So when we give pin joints, it cannot take any moment so that all moments will be released and it will just take only the axial force. And what's the most important assumption or how actually this occurs is that we assume that all external loads, they will act only the nodal points. They don't act on the members as we see in the beams, wherein the loads will just act on the beam. But in trusses, the load will be acting only at the nodal points. That is the most important assumption in trusses. That's all about trusses. Now let's try to see about cables. Cables have proven to be a marvelous, aesthetically pleasing.

You can see a picture in the screen now, which is a cable state bridge. So a lot of research has been conducted over the past two centuries. And wherein you can see the cable structures are gaining importance. So these cable structures, they're usually flexible members and they carry the loads in tension. So there will be no, I mean, cables won't take any compression. They transfer and they take only the tensile forces. So where exactly we use such structures, cable structures, generally for bridges, which have long, very long span of maybe generally around 450, 350 mm.

But it's not mandatory that those spans which are more than 350 or which is more than or less than 200, they cannot use cable structures. It's not like that. Based on the efficiency and based on the requirements, we can take a decision whether can we go with the cable bridges in this. These cable structures, they're not just limited to bridges, but we can see even in building roofs, right? Especially if the building roofs where we have a cantilever projection, there nowadays we can see a cables holding the cantilever project.

So these cable structures, they have more advantages than a beam if the spans are very large. If you look into the picture, the central span, you can look at it like the span is very long. And imagine if we try to build or if we try to insert a beam in that central span, you can just imagine how much thick or how much depth of a beam is required for such a long span. So that is totally ruled out by using cables in this picture you are seeing.

Next, let's move on to arches. If we closely observe the cables and arches, arches are nothing but a reverse curvature, a reverse to the cables, right? You can see that in picture also, wherein the mirror image in water, that looks more like a cable hanging, whereas the actual structure, the arch bridge which is above, you can see the exact opposite way. So that's why we say arches are nothing but a reverse curvature of cables and vice versa. So how these arch bridges, they achieve their strength?

As cables achieve their strength through tension, these arch bridges, they achieve their strength through compression. In order for an arch bridge to maintain its shape, they need to be rigid. Unless they are rigid, they cannot maintain that shape. And because of this, there will be a secondary forces inserted in the member or inserted in the bridges, which cause the subsequent increase in shear force and moments also. Next, we will move on to frame structures. Schematic drawing is shown on the screen in a lot of places.

In India, if you look into any metro construction, and especially if there is a metro station, you can see this kind of portal frames. Not just in metro station, but whenever there is an elevated corridor, there also you can see this portal frame kind of thing. What are these, this portal frame? Basically, it is an arrangement of columns and a beam. If you look into the picture, there are two columns, vertical members, and one beam, which is a horizontal member. And the points or the point where the column connects to beam, it is connected through a rigid joints.

In order for a structure to behave as a portal, it is very important that the joints where the beam meets the column, they need to be rigid. Then only we can see a portal action. This portal, because of this, the connection and the way it is arranged, it has high lateral stability. And the frames which you generally see, either it would be two legs, or in sometimes we can also use a three leg portal frame also. But there are cases wherein the beam is just simply supported on the column top.

But if we use such an arrangement, then we would not be able to achieve a fully portal action. The, we can, more details on this portal frame, like how, how it will be done, how, I mean, how this portal action occurs, or what exactly is this portal action, how different the moments and share force will be in the members when we connect through in this way. The more details on it we will learn in the succeeding weeks, where will, I will show you how to model and analyze this portal structure in the stat row.

The same thing in addition to portal beam or portal structure, we will also try to model and do analysis on trusts as well. And how we will also prove there that, that only axial forces will be induced in the members and there will be no bending moment and share force in the members. That we will prove it once we start modeling, analyzing the trusses in stat row. Let's wait till the coming, maybe week three, I think that's when we are going to start modeling in stat row.

So that's where it's already shown there. Now that we have completed frame structures, let's try to understand how bridges are classified. Bridges, based on the requirements or based on the situation circumstances, they are divided into various types. They are classified into various types. Let's take example of material. Based on the material, the bridges are classified as a timber. If you look into picture, it's just wooden bridge. So basically it's called a timber bridge. And if you look into the next picture, it is a steel bridge there.

And below picture says it's a concrete or it can also be a composite or it can be a PSC. Basically concrete, composite, PSC, there are different materials. We know what materials are used in concrete. The composite materials can be it's a mixture of concrete and steel or it can be different grades of concrete. So that's why it's called composite. And PSC is nothing but pre-stressed concrete wherein the concrete which is already stressed, that is before the loading is applied on the concrete member, it would be stressed.

That is why it's called pre-stressed concrete. So the bridges can be of any of these materials and based on that, we would name them. Now coming on to length. So based on the length, the bridges can be classified as a long spanned bridge, major bridges, minor bridges, culvert. Even IRC 6 use some lines on when we call a bridge as a major, minor or a culvert. I think it's around if the bridge is less than 6 meters, it would be called as a culvert. It's between 6 to 30 or 6 to 20.

I think it is minor and then above it, it's called a major. These guidelines, basically different codes have a defined the bridges. There will be, I mean generally based on the length, they will put a cap whether this particular bridge falls under minor or major or it's just a culvert. It depends on codes of different countries. But for our understanding, let's think, I mean for our understanding, we can say that based on the length, this is how the bridges are classified. And based on the superstructure or the form, we can call them as a slab bridge, wherein it will be just a slab resting on two walls kind of thing.

So that's a structure where we call slab bridge. Or we can call it a beam bridge. A beam bridge, necessarily the deck will be consisting of a beams. In case if you are not aware what the deck means, we will touch it in the next slides, wherein we will try to see different parts of a bridge. So the deck basically necessarily consists of a beams, then it's called a beam bridge. If the arrangement is truss, then it is called a truss bridge, as we saw earlier.

And if it's a superstructure is of cable state, as shown in a picture, it is called cable state bridge. And there is also a cable arrangement such that it looks like . Suspension, then it is a suspension bridge. How this cable state and suspension differ? Basically both bridges have cables in them. If you look into the picture shown there you can understand both have cables but the way the load is transferred to the structure from superstructure to substructure how the loads are being transferred. So that decides whether the bridge is cable state or it's a suspension bridge.

Next based on function for what function this bridge is going to be used whether it is going to be used for a road connecting the roads then it's called a road bridge or for carrying a railways then it's called a railway bridge or it's just people want to walk on it or even the animals want to walk and it's a pedestrian bridge or if it's a viaduct it can be called as a viaduct can look into the picture there so that's it can also be called as a viaduct bridge and aqueduct also if it's a viaduct.

If it's carrying water or it's a viaduct then we call as a viaduct bridge even the bridges are classified based on how the parts the various members are connected if the members are connected through a pin pin it necessarily refers to bolts right so generally we can achieve a pin connection using a bolt arrangement you can also call it as a bolted also in case if you want and next comes a riveted I seriously doubt whether are we still going to use riveted connection because now it is now we have better ways to connect the parts than using rivets but earlier we had so many applications or so many bridges which are riveted not just bolted we have welded also if the connections are if the parts if the members are connected through weld connection then they are called welded bridges in superstructure.

So again the bridges can be classified based on road level where the formation level we say if the road level compared to the HFL of river that is high flood level of the river if the road level is above the high flood level of river then it is called high level bridge or if the road level is below the HFL of river then it is called submersible bridges. So for submersible bridges there is a good chance that if because of some reasons the water starts flowing at a high flood level this flood can be of 1 in 5 or it can be 1 in 100.

So suppose if we are referring to 1 in 100 flood level that is the flood which recurs after every 100 years then there is a good chance that our bridge will be submerged into the water because it is situated below the HFL of water river. Next we have a marvelous bridges here based on clearance for navigation let us say that we have constructed a bridge over the rivers or seas and let's say a steamer or a ship wants to pass below the bridge. For this purpose we can see bridges such as bascal wherein wherein when there is a need for a ship to pass to below the bridges then the basical structures will just rise or it will just vertically rise so that it will leave the places for the board of either a ship or steam or whatever may be the vehicle it can just pass through it.

Once it passes then it can be again released back to the starting position so that is called basical basically moves in vertical direction up and down so you can see in the picture right there wherein the bridge has moved upwards so that to allow a floating body to pass below. In the swing it will be something similar to the basical but it will rotate in the horizontal direction and again coming back to transporter you can see in the picture right below there wherein you can see some cables also.

These cables can travel from that end to this end and it can carry some weights next we have even bridges are classified based on service whether are you going to use that bridge for a temporary service or it's for a permanent service. A very interesting picture is shown on the right here wherein you can see a series of boats are placed side by side and a kind of mat has been placed over them and people are traveling above it. It is a very interesting photo I see that even this is a temporary service maybe maybe this particular arrangement is not required for a long run maybe it's because of some circumstances they were forced to use these boats as a bridge.

That's very interesting not all bridges need to be of concrete steel or composite materials we can see even the boats would serve here as a bridge even so these this is basically we these bridge I mean these boats may need will generally won't be there for a extended period of time it's just for a temporary purposes the permanent bridge basically whatever flyovers or bridges which we see in today's life they are for a they are called as a permanent so permanent so permanent so permanent means it doesn't mean that they will last for centuries and centuries but permanent in the sense they will live till there those bridges will be functional till their designed life as I said earlier the general designed life would be 120 years or 100 years based on the codes of the country the bridges can be classified based on the redundancy degree of redundancy basically whether we can say if it's a statically determinate bridge or statically determinate bridge or we can call it a bridge as statically indeterminate so what exactly statically determinate structures so if you could recall your basics those structures whose forces can be solved using the equilibrium equations that the three equilibrium equations generally for if we are able to solve them using those three equilibrium equations then it is called a statically determined structure i think it has been a lot of theory till now so let's try to brainstorm the picture in the slide is of a fourth bridge what do you think is it statically determined structure or it's statically indeterminate structure Just give a thought. If you look into the joint, that is where you can see a concrete structure in the water there. And if you look into this joint here, we can see that there is some kind of connection here. It can be pin joint or it can be rigid connection.

Just think all this and just brainstorm sometime and you will see whether this structure is statically determinate or indeterminate.

Want the rest of Design of Bridge Substructures / Piers using STAAD.Pro?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Design of Bridge Substructures / Piers using STAAD.Pro course

The remaining 42 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Design of Bridge Substructures / Piers using STAAD.Pro course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.