Lesson finished
Lesson finished
Unlock all 9 lessons of CAE Simulation using SolidWorksFull course ₹40,000 · paid
Nonlinear Analysis, 2D Simplification and Material Models in SolidWorks
A free lesson from Skill-Lync's CAE Simulation using SolidWorks course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Introduction to types of FEA analysis - Part 2”
What will you learn in this free CAE Simulation using SolidWorks lesson?
The instructor explains geometric, material and contact nonlinearity, then sets up a punch and die sheet metal study as a nonlinear dynamic 2D simplification. The lesson covers load curves, time steps, contact sets, an axisymmetric example and the material model options, from linear elastic to von Mises plasticity.
- Geometric, material and contact nonlinearity
- Setting up a 2D simplified nonlinear dynamic study
- Load curves, time steps and frictional contact sets
- Choosing material models such as von Mises plasticity
What comes after lesson 3?
Later in Skill-Lync's CAE Simulation using SolidWorks course (paid): lesson 4, 1D/2D/3D FEA Analysis on a Uniform Loaded Cantilever Beam; lesson 5, Buckling Analysis of Cyclonic Separator Stand; lesson 6, Help video for Buckling Assignment. The full course has 9 lessons (3 h 39 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Part 1
Now let's move back to the slides. So depending upon the material stress contours, we should decide whether we need to move on to a non-linear module or linear module to perform an analysis. Similarly, in the dynamic, we do have a linear dynamic analysis under which all the vibration and frequency analysis and finally we have a non-linear dynamic analysis too. So as I mentioned before, static analysis involves time independent forces. The intermediate results are not reliable upon. The linear static analysis, as we saw in the example, the relation is going to be a linear one.
Hence, in order to capture the non-linear effects, you need to use a non-linear module. In the static module, all the non-linear effects in the material are captured and the solver takes longer time to converge to the solution. So dynamic analysis is performed to understand the behavior of a material under time varying loads. So what is non-linear analysis and why do we perform it? As we saw in the previous example, where the plate was pulled by a tension force, within the elastic limit, the stiffness of the module is assumed to be constant.
Once the material causes the yield strength value, its stiffness changes constantly with time. To capture all the non-linear effects, the solver goes back to the material and evaluates the stiffness before proceeding to the next step. To capture the non-linear effects, we need to perform a non-linear analysis. This is the graph. So a linear static analysis will follow a path by extrapolating the elastic region. But a non-linear analysis, after passing through the elastic point, the linear relation between the stress and the strain doesn't hold good anymore.
So now let's look at some of the non-linear effects that can occur in a material. So non-linear effects can occur due to change in geometry. So when an object is acted upon by a force and we are performing a static analysis, solver detects large deformation, we will be prompted to perform a non-linear analysis in order to capture the non-linearities that were caused due to the change in geometry. So let's open SOLIDWORKS and look at one such example. Click on the file and new part. Let's click the front plane, right-click, sketch, select the rectangle, raw rectangle, smart dimension it as 50 mm and 50 mm.
Make sure you have the correct unit system. Here I have changed it. So go back to the edit sketch option. Click on here. Select 50 mm. Select this and then import 50 mm. So once you do that, go to Features. So extrude the sketch to a distance of 1000 mm and click OK. Move on to the simulation. Perform a new study. Select the static model here. So now I right-click and apply the default material. Right-click on the fixtures. Select fixed geometry. Fix one end. And click OK.
Then again right-click on the force. Select this particular face. And choose the direction in which you want to act this force upon. Make sure your force points downwards. Input the value of 500 N. And click OK. Now right-click on the mesh and choose Mesh and Run. So you can see we have got the results instantly. Now let's see what happens if I increase the force by a factor of 100. So here the solver has detected large displacement. And hence it's prompting you to switch over to a non-linear analysis to get reliable results.
In case if you want to switch over, you can get just given S. So apart from geometric linearities, we do have material non-linearities. So material non-linearities can occur due to two reasons. The first one being creep. The other one is the elastic limit. In creep, if the material is acted upon by a load for a prolonged period of time, its stiffness doesn't remain constant. Instead, it starts varying with time. Hence, we need to perform a non-linear analysis on such cases. Now, secondly, beyond elastic limit, any metal will move into the non-linear region.
While the non-metals can behave non-linearly within the elastic limit. And finally, apart from geometric and material non-linearities, we do have contact non-linearities, which are caused by the changing status of the contacts throughout the simulation. For example, if we have a simulation where we have a cantilever beam, there is a box which lies below the cantilever beam. Now, if I apply a force on this cantilever beam, the stress contours on the beam will be linear until it makes a contact with the box below it. So once it makes a contact with this box, the stress contour on the beam will no more be linear even though it is within the elastic limit.
Hence, depending upon the contact status, non-linearities can step in even though you are well within the elastic limit. Now, in SOLIDWORKS, if you are performing a non-linear analysis, you are provided with two options. First one being the static analysis, that is, you perform a non-linear static analysis. The second one is a non-linear dynamic analysis. Further, you have a small option called the use 2D simplification, wherein if your model is symmetric about a plane or an axis, you can use this 2D simplification option. Run a 2D simulation and then view at the 3D results, look at the 3D plot by replicating the results along the axis of symmetry.
So now let us look at how to use this 2D option and perform a non-linear static as well as a dynamic simulation. So open SOLIDWORKS, click on the file, choose a new part and open the model that you have been provided with. So once you import the model, rotate, zoom and pan the geometry for any errors in the model. In our case, the model is fine. So let us proceed with the simulation. Before we proceed with the simulation, I will explain about the simulation before we look into how to set up it.
In the simulation, a punch is used to deform the sheet metal into the shape of the die. So now let us proceed with the simulation. During this process, we will be looking at the stress that will be developed upon the sheet when it is being acted upon by the punch. Hence, to capture the variation of the stress during this process, we need to perform a non-linear dynamic simulation to get accurate results. So click on the new study, select non-linear dynamic 2D simplification and click OK. Here, you need to select the plane about which your model is symmetric.
In our case, it is the front plane and we are going to have a depth of 0.015. That is the thickness up to which you need to replicate this 2D results to get the 3D object. Once you do this, you can see we have got the 2D representation of our model. Now, click on the parts here and right-click. Apply the default alloy steel material to all the parts. Click on the sheet metal and apply plain carbon steel as the material. Now, right-click on the fixtures. Click on fixed geometry.
Select the 3 edges of the die to fix the die in a position all throughout the simulation. Now, right-click and use the fixed geometry. Select these 2 edges of the plate. To ensure that the plate doesn't slip off during the bending process. Again, right-click on the fixtures. Choose fixed geometry. And expand the advanced selection. Select this portion of the punch. And activate the translation along these 2 directions. Since the punch needs to move down to a distance of 10 mm, reverse the direction and click OK.
Here now we have fixed the geometry. And the punch will be moving down by distance of 10 mm. Before you hit OK in the translation, we need to look at one crucial option that is available in a dynamic simulation. Here, you have a curve that represents the loading in this problem. As you can see, in the x-axis we have the time and in y-axis we have the load. In our case, it is a translation load. So, from 0 to 1 second, we are loading this geometry.
At 1 second, we are applying the whole load. For example, let us say I have 5 N of load that needs to be acted upon. In that case, at 0 seconds, we will have 0 N. At the end of 0.5 seconds, we will have 2.5 N. And at the end of 1 second, we will have 5 N totally acted upon on the material. So, we are increasing the load gradually but linearly in this case. And since the translation is along the negative y-axis, we have the graph pointing downwards.
Now, let us look at the various other options that are available defining load step. So, when you click on edit, you will be given option to edit your loading steps. In the first column, you have the seconds and in the y, you have the loading ratio. In this current scenario, at 0 seconds, we have 0 loading ratio. And at 1 second, we have 1 as the loading ratio. Let us suppose we want to look at unloading type. Here, the maximum value of force will be applied at time equal to 0.
And it will be gradually unloaded from the material. Finally, we have a loading and unloading type of graph. Let us look at it. You can see. You can see. So before one second, the load is applied and unloaded as well. In between the simulation, we reach the maximum load and gradually it is unloaded off. Just directly apply the load here. Click OK. And hit OK here. And before we run the analysis, let's look at the properties. You can see we have been provided various options to adjust the time step and help in convergence of the solution.
In our case, we are not going to change them. But if you face any convergence issue in your own simulation, just try to change them. Now, if you want to understand this time stepping in detail, let me demonstrate it using a small calculation here. I have a solver. I have a time equal to 0 and a time equal to 5 seconds. I am applying a force. At 0 seconds, it is 0 Newton. And at 5 seconds, it is going to be 10 Newton. Here, the solver will initially proceed by defining the stiffness matrix and start solving for the unknowns. But after it solved for the first step, while going for the second step, we define a time, we define a time step. In this case, let's assume it to be 0.1 seconds. Then the solver will move to 0.1 seconds and redefine all the matrix depending upon the previous step, find for the unknowns in this current step. After this particular step, it will again increment the solver time by 0.1 seconds. And this process will go on.
In case, if your solver experiences convergence issue, that is, if the solver is not able to get the same result while iterating to find the unknowns, it will increase the time steps by some factor. Here, we have given the initial time step to be 0.1 and it may increase the time step to 0.5 seconds. Hence, after solving for the 0.1 seconds, it will move to 0.6 seconds. And this process continues until you have solved for all the 5 seconds. Hence, for this reason, you specify a minimum time step, help the solver converge to a solution.
Now, let's go back to SOLIDWORKS. Apart from controlling the start and end time, you have several other options that you can use depending upon your requirement. Let's click OK. Here, since we have lots of parts, we need to define proper contacts in order to avoid interpenetration of the parts. To understand what it is exactly, I am going to run this analysis without defining the contacts properly. So, as you can see, since we did not define the contacts properly, the parts have interpenetrated themselves. This is totally unrealistic because in real life, if a material needs to penetrate another material, it needs to follow a particular mechanism to fail the other material and go through it.
So, this is totally unrealistic. Hence, to avoid this, first hide the stress plot by right-click on the stress, choosing the hide option. Right-click on the component contact and select contact set. Since this die will come in contact with this sheet here, select the edges of the die. Make sure you select only the edges and not the face and define them as the source. Now, for the target, select this edge of the sheet metal. Define a frictional contact and make sure you have no penetration selected here and click OK.
Similarly, right-click on the component contacts again and define another contact between this sheet metal edge and the edges of the die. Define the friction and make sure you have no penetration and click OK. In case, if you are going to interchange the target and the source, you will end up getting a convergence issue and your simulation will fail. Now, that we have defined the context properly, let us rerun the simulation and look at the results. Our simulation is successfully completed. Right-click on the stress and animate to look at the results.
Now, if you want to look at the 3D plot of this simulation, right-click on the result and show us 3D plot. This 3D plot is created by replicating the 2D result along the depth distance that we defined earlier in the simulation. Right-click on the result and click animate. And this is how we perform a 2D simplification, non-linear dynamic analysis on a 3D model. This way, we will be able to reduce the computational effort and get accurate results. Now, let us go back to the presentation. Before I proceed on with the presentation, let me show you another example where our model is symmetric about an axis.
Let me import the model. Here, you can see the 3D model is already simplified as one-fourth of the whole model. Now, we are going to simplify it further by selecting the axis of symmetry here. Let us begin by clicking on the simulation. Click on new study. Select non-linear dynamic. Use 2D simplification. And click OK. Here, since our model is symmetric about an axis, select the axis symmetric option. Choose the plane for cross-section. And then select the axis of symmetry. Once you do that, you will be provided with the 2D simplified model and you can proceed with the simulation.
So, I am not going to do the simulation for you. This will be provided to you as a challenge. But I will explain the problem statement here. We will be looking at the deformation that will be caused by the sphere when it is pressed onto the plate. So, here, this sphere will be moved forward and the plate should be fixed as it is. We will be performing a loading and unloading type of simulation. And then look at the stress that is developed during this process. Now, in case, if you want to modify your contact distance or move your parts apart before proceeding with the simulation, click on the model here.
Choose the move body options. And select the body that you need to move. Choose the translate option here. Then, in our case, we need to lift the sphere up by some distance. Let us say it is 0.5 mm. You can see we have lifted the sphere by 0.5 mm. The y direction. Now, let us select OK. So, here we have successfully lifted the sphere. Now, we can proceed with the simulation. Let us move back to the presentation. Now, with those examples, we have understood how to perform a non-linear dynamic simulation on a 2D simplified model.
In SOLIDWORKS, you have been provided with various models for the materials to perform a non-linear analysis. That is, if you are noticed properly in the simulation, as the punch presses into the sheet metal, the sheet metal deforms like an elastic material. In other words, if you end up removing the die, the sheet metal will return back to its original position without any plastic deformation that has been occurred. This would look like unreal. It is because we have chosen the wrong material model to represent the behavior of the sheet metal.
To define your material model correctly, right click on the edit material and in the model type, you have been provided with a list of options depending upon your requirement. So, with the right settings, we can capture the plastic deformation that has been caused by the punch during this operation. So, as I have mentioned before, in linear elastic isotropic, the material properties are assumed to be constant throughout the X, Y and the Z direction. And after loading, if the material is unloaded, it will return back to its original position without any plastic deformation.
In the linear elastic orthotropic, you need to define the material properties along X and Y direction in order to perform the simulation. This way, you will be able to capture the behavior of orthotropic material, but this particular model will revert back to its original shape after the loads are unloaded. While choosing this linear elastic orthotropic, you need to input values for elastic modulus along Y and Z as well as Poisson ratio in all the other planes. To do this, you need to right click on the library material, copy it, paste it in the custom materials and then input all these values before you use it in the SOLIDWORKS model.
Now, non-linear elastic, here this model is used to capture the effects of non-linearities, but the deformations are still elastic in this model. In plasticity von misers, when the stress value are above the yield value, the plastic deformation sets in. So, these effects will be captured accurately by this model. Apart from the plasticity von misers, we do have plasticity Tresca and plasticity trucker pager, which are complex models developed over the plasticity von misers. Now, if we use materials such as rubber, which have high deformation rate for a small load, that is, even if they are in the linear elastic region, their displacement is large for a given load.
To simulate all these effects, we use hyper-elastic and the visco-elastic model is used to simulate the different effects that is produced by the same material at different loading rates. Finally, using this Nittlinol model, we can model the non-linear effects without allowing plastic deformations to set in, even though the model experiences high deformation. So, by choosing the appropriate model, one can capture the deformation process of a material using SOLIDWORKS simulation. I hope this lecture was helpful enough to understand the difference between using a static and a dynamic analysis in SOLIDWORKS.
Go ahead, use the models that you have been provided with and attempt... I'll see you guys in the next video. Bye.
Part 2
चलिए slides पे चलते हैं. अब material stress counters पे depend होके decide करना होगा कि हमें non-linear module के साथ जाना है या linear module के साथ analysis परफॉर्म करने के लिए. ऐसे ही dynamic में भी हमारे पास है linear dynamic analysis जिसमें सारे vibration frequency analysis आते हैं और फिर अंत में है non-linear dynamic analysis. तो जैसे मैंने बताया static analysis time dependent forces हैं. intermediate results पे हम ज्यादा विश्वास नहीं कर सकते. linear static analysis जैसा हमने example में देखा इसमें relation linear होगा. तो non-linear को capture करने के लिए non-linear module पे जाना होगा.
static module में सारे non-linear material capture होते हैं और solver को ज्यादा time लगता है. solution पे converge करने में. dynamic analysis material का behavior समझने के लिए perform किया जाता है under time worrying loops. तो non-linear analysis क्या है और इसे क्यों perform करते हैं? जैसा पिछले example में देखा जहां plate को tension force के द्वारा pull किया जा रहा था तो elastic limit के भीतर module की stiffness को constant assume करेंगे. जैसे ही metallic yield strength value लाएगा उसकी stiffness लगातार time के साथ बदलेगी.
non-linear effects को capture करने के लिए solver material पे जाता है फिर से और stiffness evaluate करता है. अगली step पे बढ़ने से पहले non-linear effects capture करने के लिए non-linear analysis perform करना पड़ता है. ये graph है linear static analysis के लिए हम ये path follow करते हैं. elastic vision को extra polite करके हम non-linear analysis में elastic point pass करने के बाद stress और strain के बीच का linear relation अब इतना सही नहीं रहेगा. अब material में आने वाली कुछ non-linearities को देखते हैं. ये geometry के बदलाव के कारान आ सकती है. जब कोई object पे force लगाया जाता है और हम static analysis perform कर रहे हैं तो solver को काफी बड़ा deformation दिखेगा. और � उसको non-linear analysis perform करना होगा. जियोमेट्री के बदलाव के कारान जो non-linearities आई हैं उन्हें capture करने के लिए.
SOLIDWORKS खोल के ऐसे एक example को देखते हैं. फाइल में new part पे जाएं और front plane पे क्लिक करते हैं. राइट क्लिक, sketch, rectangle set करें. 50 mm पे smart dimensions करें. ये 50 mm ध्यान रखें कि आपके पास सही unit system हो. यहां मैंने change किया है. तो addit sketch option पे फिर से जाएं. यहां क्लिक करें. 50 mm सेलेक्ट करें. यहां 50 mm. फीचर्स पे जाएं. 1000 mm का distance ले. ओके क्लिक करें. फिर simulation पे जाएं. यहां static model सेलेक्ट करें. राइट क्लिक करके material चुने. फिक्स्चर्स पे राइट क्लिक करें. fix geometry सेलेक्ट करें. एक end fix करें. ओके दबाएं. फिर से राइट क्लिक करके force इस face को सेलेक्ट करें. और direction चुन जिस पे आपको यह force लगवाना है. ध्यान रखें कि force नीचे की ओर point कर रहा हो. फिर value input करें. ओके दबाएं. फिर mesh पे राइट क्लिक करें. फिर mesh और रंचुने. तो आप देखेंगे कि मुझे हाथो हाथ result मिल गया है. अब क्या होगा? अगर मैं 100 के factor से force को बढ़ा दूँ यहां solver ने काफी ज्यादा displacement detect करा है. इसलिए सही results पानी के लिए आपको non-linear analysis पे जाने को कह रहा है. आपको बदलना हों तो आप बस yes दबाएं. जिएometric linearities के अलावा material non-linearities भी होती हैं. यह दो कारण की वज़ा से आ सकती हैं. creep और दूसरा elastic limit.
creep में अगर material पे load लगा है ज्यादा time के लिए तो उसकी stiffness constant नहीं रहती. यह time के साथ बदलने लगती है. इसलिए non-linear analysis परफॉर्म करना पड़ता है. ऐसे case में दूसरी बात elastic limit में कोई भी metal non-linear reason में चला जाता है. और non-metals non-linear तरीके से behave करने लगते हैं elastic limit के भीतर. अंत में geometric और material non-linearities के अलावा आती है contact linearities जो की simulation में contacts के बदलते status की वज़ा से आती हैं. जैसे अगर simulation है जिसमें cantilever beam तो एक box होता है जो इसके नीचे होता है. अब अगर इस cantilever beam पे force लगे तो beam पे stress contours linear होंगे. जब तक वो नीचे वाले box से contact में ना आ जाए.
एक बार इस box के साथ contact हो गया, beam पे stress counters linear नहीं रहेगा. जबकि वो elastic limit के भीतर है तब भी. इसलिए contact status पे depend करता है non-linearities आ सकती है. Even अगर आप elastic limit के काफी भीतर हो. अब SOLIDWORKS में अगर आप non-linear analysis कर रहे हो तो आपको दो options मिलते हैं. एक static analysis मतलब आप non-linear static analysis परफॉर्म करते हैं. दूसरा है non-linear dynamic analysis. आगे एक छोटा सा option आता है use 2D simplification जिसमें अगर आप plane या axis के हिसाब से symmetric हैं तो आप ये use 2D simplification का इस्तमाल कर सकते हैं. 2D simulation रन करके 3D results में देखने के लिए 3D product को देखें, results को replicate करके axis of symmetry के along. अब देखते हैं इस use 2D simplification को काम में लेके non-linear static और dynamic simulation कैसे perform करना है.
SOLIDWORKS खोल के file पे click करें, new parts चुनें और जो आपको model मिला है वो खोलें, एक बार model input कर लें, फिर rotate, zoom करें और geometry देख लें कि कुछ model में errors तो नहीं हैं. यहाँ model सही है, तो simulation की ओर बढ़ते हैं, इसको setup करने के पहले मैं आपको थोड़ा सा इस पे कुछ बता देता हूँ. simulation पे punch use किया जाता है, sheet metal को deform करके die के shape में बदलने के लिए, अब इस process के दौरान, sheet पे जो stress develop हुआ है, हम उसे देखेंगे, जो punch के द्वारा लगा है.
इसलिए इस process के दौरान, stress के vibration को capture करने के लिए, हमें non-linear dynamic simulation यूज़ करना होगा, सही results के लिए, new study पे किलिक करें, non-linear dynamic 2D simplification को select करें, ok दबाएं, यहाँ plane select करना होगा, जिसके about आपका model symmetric है, हमारे case में ये front plane है, हम depth रखेंगे, 0.015. जहां तक आपको ये 2D results replicate करने हो, 3D object पाने के लिए, अब हमें model का 2D representation मिल गया है, अब parts पे click करें, और right click करें, apply the default alloy steel material, सारे parts पे, sheet metal पे click करें, और material में plane carbon steel apply करें, fixtures पे right click करके, fix geometry पे जाएं, die की 3 edge select करें, ताकि die एक ऐसी position में fix हो जाए, पूरी simulation के दोरान, अब right click fix geometry यूज करें, plate की ये 2 edges select करें, ध्यान रखें कि plate फिस लेना, इस bending process के दोरान, फिर से fixtures पे right click करें, fix geometry चुनें, और advanced selection को expand करें, punch का ये portion select करें, और इन 2 directions के along translation देखें, क्यूंकि punch को नीचे जाना चाहिए 10 mm के distance से, तो ये करें, direction reverse कर दें, और ok दबाएं, अब हमने geometry fix कर दी है, और punch 10 mm के distance से नीचे जाएगा, translation में ok दबाने से पहले, हमें एक important option देखना होगा, जो dynamic simulation में available है, यहां ये curve है, जो इस problem की loading रिप्रेजेंट करता है, x-axis पे time और y-axis पे load, हमारे case में translation load है, तो 0 से 1 second में हम इस geometry को load कर रहे हैं, और 1 second में हम पूरा load apply कर रहे हैं, जैसे मेरे पास 5 newton का force है, जो लगाया जाना है, तो ऐसे case में 0 second पे 0 newton होगा, और 0.5 seconds के अंत में 2.5 newton होगा, और 1 second के बाद total 5 newton लग जाएगा, तो हम धीरे धीरे और linearly load बढ़ा रहे हैं इस case में, और क्योंकि translation negative y-axis के along है, हमारा graph नीचे की ओर point कर रहा है, अब दूसरे भी options जो available हैं, उन्हें देखते हैं, edit पे क्लिक करने पर हमें ये loading step edit करने का option देगा, पहले column में है seconds और y में है loading ratio, यहाँ 0 seconds में 0 loading ratio है, और 1 पे 1 है, मानो हमें unloading type पे देखना हो, यहाँ सबसे ज्यादा force टाइम बराबर 0 आप apply किया जाएगा, और फिर ये धीरे-धीरे material से unload होगा, तो finally हमारे पास loading और unloading type के graph हैं, उन्हें देखते हैं, एक second के पहले load लगाया गया है और unload भी किया गया है, simulation के बीच हम maximum load लोड़ देखें, पर पहुँचते हैं और धिरे-धिरे ये unload हो रहा है.
यहां directly load apply करें, ok दबाएं, यहां ok करें, और analysis run करने से पहले properties देखते हैं. Time step adjust करने के लिए, देखे हमें कई options दिये गए हैं, ताकि solution के convergence में भी मदद मिले. हमारे case में हम इन्हें नहीं बद देंगे, पर आप अपने case में ऐसा कुछ हो, तो बदल सकते हैं. इस time stepping को detail में जानने के लिए, मैं आपको एक छोटी सी calculation से समझाता हूँ. मेरे पास time बराबर 0 और time बराबर 5 seconds हैं. 0 पे मैं 0 Newton का force लगा रहा हूँ और 5 पर 10 Newton.
यहां solver पहले stiffness matrix से शुरू करेगा और unknowns को निकालना शुरू करेगा. पर first step तक solve करने के बाद, second step पे जाते वक्त हम time step define करेंगे. इस case में 0.1 seconds एज्यूम करते हैं, फिर solver 0.1 seconds पर जाएगा और पूरी matrix को redefine करेगा, depending on हमारी पुरानी step. और इस current step में unknowns को निकालना शुरू करेगा. इस step के बाद यह फिर से solver time को बढ़ाएगा, 0.1 seconds से और यह process चलती रहेगी. अगर आपके solver को convergence issue आए, मतलब अगर उसको वही result नहीं मिल रहा हो, unknowns निकालते वक्त, तो यह time step किसी factor से बढ़ा देगा.
यहां हमने initial time step 0.1 दिया है, और यह 0.5 seconds तक इसे बढ़ा सकता है. इसलिए 0.1 seconds के लिए solve करने के बाद, यह 0.6 seconds पे चला जाएगा, और process चलती रहेगी, जब तक आप सारे 5 seconds के लिए ना कर लें. इसलिए इस reason के लिए आप minimum time step specify करें, ताकि solver solution पे converge कर सके. SOLIDWORKS पे जाते हैं, start और end time control करने के लावा, कई और options हैं, जो आप अपनी requirement के हिसाब से काम में ले सकते हैं.
ओके पर क्लिक करें, यहां क्यूंकि हमारे पास बहुत सारे parts हैं, हमें सही से contacts define करने होंगे, ताकि inter penetration ना हो parts में. यह समझने के लिए मैं analysis run करता हूं, contacts को बिना अच्छे से define किये, तो देखिए ऐसा करने पर parts inter penetrate हो गए हैं, यह बिलकुल unrealistic है, क्योंकि असल में एक material को दूसरे में गुशने के लिए एक particular mechanism follow करना होता है, दूसरे material को feel करके उसमें जाने के लिए, तो यह बिलकुल भी असल नहीं है, तो इसको avoid करने के लिए, पहले stress hide दबाएं, इसको छुपाने के लिए, component contacts पे right click करें, और contact set चुने, क्योंकि यह die यहाँ sheet में घुस रही है, तो die एक edges को select करें, बस edges ही select करें, face नहीं, और इन्हें as source define कर दें, अब target के लिए, इस sheet metal की age select करें, frictional contact define करें, ध्यान रखें, यहाँ कोई penetration ना हो, ok दबाएं, ऐसे ही फिर से component contacts पे right click करें, एक और contact define करें, इस sheet metal की age और die की edges के बीच, friction define करें, ध्यान रखें, यहाँ कोई penetration ना हो, और ok दबाएं, अगर आपको target और source को आपस में बदलना हो, तो आपको convergence issues आएंगे, और simulation फेल हो जाएगी, अब contacts सही से define करने के बाद, simulation को फिर से run करते हैं, और results देखें, हमारी simulation सही से पूरी हो गई है, stress पे right click करके animate करें, results को देखने के लिए, इस simulation का 3D plot देखने के लिए, results पे right click करें, और show us 3D plot पे जाएं, यह 3D plot 2D results को replicate करके बनाया गया है, depth distance के along, जो हमने simulation में पहले define की थी, results पे right click करें, फिर animate पे जाएं, और ऐसे हम 2D simplification करते हैं, non-linear dynamic analysis 3D model पे, ऐसे हम computational effort कम कर पाएंगे, और सही results मिल पाएगा, presentation पे फिर से जाते हैं, इसके पहले एक और example देता हूँ, जहां हमारा model, axis के about symmetric है, model import करता हूँ, यहां 3D model पहले से ही simplified है, as पूरे model का one fourth part, हम इसको अब और simplify करेंगे, axis of symmetry select करके, simulation पे click करके शुरू करते हैं, new study पे click करें, non-linear dynamic select करें, फिर use 2D simplification पे जाएं, ok दबाएं, यहां क्यूंकि हमारा model, axis के about symmetric है, axis symmetric option select करें, cross section के लिए plane चुने, फिर axis of symmetry चुने, यह करने पर आपको 2D simplified model मिलेगा, और आप simulation की ओर बढ़ सकते हैं, मैं यहां simulation नहीं करूंगा, यह आपके लिए challenge है, पर मैं problem statement बता देता हूँ, हम deformation देखेंगे, जो की sphere की वजह से हुआ है, जब उसे plate से press किया जाता है, यहां यह sphere आगे बढ़ेगा, plate ऐसे ही fix रहेगी, हम loading और unloading type का simulation करेंगे, और फिर इस process के वक्त, जो stress develop हुआ है, उसे देखेंगे, अगर आपको अपना contact distance बदलना हो, या अपने parts को move करना हो, तो simulation के पहले, तो यहां model पे क्लिक करें, move body option चुने, और वो body select करें, जिसे आप move करना चाहते हों, यहां translate option चुने, हमारे case में, फिर हम इस sphere को थोड़े distance से उठाएंगे, मानिए 0.5 mm, हमने यह कर दिये हैं, y direction में, अब हम इस simulation पे चलेंगे, presentation पे चलते हैं, फिर से, इन examples के साथ हमने समझ लिया है, कि non-linear dynamic simulation कैसे perform करते हैं, 2D simplified model पे, SOLIDWORKS में, आपको कई models दिये गए हैं, materials के लिए, non-linear analysis परफॉर्म करने के लिए, अगर आपने ध्यान दिये हूँ, तो simulation में, तो जैसे punch, sheet metal को press करता है, sheet metal, एक elastic material की तरह deform हो जाती है, अगर आप die हटा दें, तो sheet metal अपनी original जगह वापस चले जाएगी, बिना किसी deformation के, ये नहीं हो सकता, ये unreal देखता है, क्योंकि हमने गलत material model चुना है, sheet metal के behavior को represent करने के लिए, अपने material model को सही से define करने के लिए, edit material पे right click करें, और model type में, हमें पूरे options के list दी गई है, तो सह इस settings के साथ, हम plastic deformation capture कर सकते हैं, जो इस operation के दौरान, punch की वजह से हुआ है, तो जैसा मैंने पहले कहा, linear elastic isotropic में, material properties को constant assume किया जाता है, पूरे x, y और z direction में, और loading के बाद, अगर material unload किया जाता है, तो ये अपनी वही position पे वापस चला जाता है, बिना किसी plastic deformation के, linear elastic orthotropic में, आ define करनी होती है, x और y direction के along, simulation perform करनी के लिए, इस तरीके से, आप orthotropic material का behavior capture कर पाएंगे, पर ये particular model, अपने original shape पे वापस जाएगा, loads unload होने के बाद, ये linear elastic orthotropic, चुनते वक, आपको elastic modules के लिए input देना होगा, y और z direction के along, और इसके साथ ही, बाकि सारे planes में, poison ratio भी, ये करनी क material पे right click करें, copy करें, और custom materials में paste करें, और ये सारी values input दें, SOLIDWORKS model में use करने से पहले, अब आता है non-linear elastic, ये model non-linearities के effects को capture करने के लिए use किया जाता है, पर इस model में deformation elastic ही होते हैं, plasticity one misses में stress value या yield value के उपर plastic deformation set होता है, तो ऐसे effects इस model से अच्छे से capture होंगे, इसके अलावा हमार पास है, plasticity, Treska, और plasticity, Drucker, Pager, जो की complex models हैं, जो plasticity one misses के उपर develop किये गए हैं, अगर हम materials use करें, जैसे rubber, जिनका high deformation rate होता है, small load के लिए, मतब अगर वो elastic linear region में भी हैं, तब ही displacement ज्यादा होता है, given load के लिए, इन सब effects को simulate करने के लिए, हम hyper elastic use करते हैं, और visco elastic model use किया जाता ह simulate करने के लिए, different effects को, जो same ही material ने produce किये हैं, different loading rates पे, अंत में nitinol model use करके, हम non-linear effects को model कर सकते हैं, बिना passive deformation को set in करने के लिए, allow करें, भले ही model high deformation experience कर रहा हो, तो सही model choose करके, आप material की deformation process capture कर सकते हैं, SOLIDWORKS simulation use करके, आशा करता हूँ, इस lecture से आपको मदद मिली होगी, कि static और dynamic analysis को चुनने में क्या अंतर होता है, SOLIDWORKS में, जाएं, और आपको जो model दिये गए हैं, उनको use करें, और Challenge दिये गए हैं, उसे करें, मिलते हैं!
challenge Buy, buy, buy, buy, buy, buy, buy, buy.