← Previous lessonFree lesson 2 of 3 · lesson 2 of 9Next lesson →

Unlock all 9 lessons of CAE Simulation using SolidWorksFull course ₹40,000 · paid

Price & syllabus
Free lesson · 18 min · no payment

Static vs Dynamic Analysis and a Plate With a Hole in SolidWorks

A free lesson from Skill-Lync's CAE Simulation using SolidWorks course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Introduction to types of FEA analysis - Part 1”

What will you learn in this free CAE Simulation using SolidWorks lesson?

The instructor contrasts static and dynamic analysis, using a cantilever beam to show why intermediate static results are not reliable. In SolidWorks, a 50 mm plate with a 10 mm hole is pulled with 1000 N, then the force is raised tenfold to show when a nonlinear static study is needed.

  • Quasi-static loading versus dynamic inertia and damping
  • Modelling a plate with a hole in SolidWorks
  • Setting fixed geometry, tension load and default mesh
  • Spotting stress above yield and switching to nonlinear

What comes after lesson 2?

The next free lesson is lesson 3, “Nonlinear Analysis, 2D Simplification and Material Models in SolidWorks” (42 min). Later in Skill-Lync's CAE Simulation using SolidWorks course (paid): lesson 4, 1D/2D/3D FEA Analysis on a Uniform Loaded Cantilever Beam; lesson 5, Buckling Analysis of Cyclonic Separator Stand; lesson 6, Help video for Buckling Assignment. The full course has 9 lessons (3 h 39 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Part 1

Hey everyone, welcome to yet another video in FEA using SOLIDWORKS. So in this video, we'll discuss about what a static analysis is and how it's different from a dynamic analysis and what are the other different types of analysis that is available in SOLIDWORKS and when do we use them. Let's begin with the BPT. So structural analysis. So the term structure not only refers to the civil structures like bridges and buildings but it also can be used to refer the mechanical parts that we often use in an industry.

To understand the stress and strain produced by the loading on these mechanical structures, we perform finite element analysis to understand the behavior. Here in a finite element analysis, the unknown displacements are initially found out and then they are re-substituted back to get the reaction force and other derived quantities like stress and strain. Basically, a structured analysis problem can be classified into static analysis and dynamic analysis depending upon the loads that are acted upon. Apart from this classification, we do have 1D, 2D, 3D finite element analysis that is classified based upon the element that is used.

We have several other specific analysis like the buckling analysis, fatigue analysis which serve the purpose that they were designed for. So SOLIDWORKS has separate modules for each of the special analysis. Now let's look at the basic classification of analysis that is static and dynamic analysis. If you consider a static analysis, we assume the forces that act upon the model are quasi-static. In other words, the loads that are acted upon on the model increase gradually such a way that the acceleration velocity, they can be neglected. While on the other hand, the dynamic analysis, all the inertial and damping effects are considered and we solve for the acceleration and velocity of the components before we find out the stress and strain.

So compared to a static analysis, a dynamic analysis is much more time consuming. So also if you consider in a static analysis, you start the simulation at point A and if B is your final end, the intermediate results that you get may follow any path and get to the final results. Hence, you can never relay upon the intermediate values in a static analysis. On the other hand, in a dynamic analysis, if you have two destinations, the path will be precise that the intermediate values that you get for stress and strain are reliable and can be used.

To be even more specific, let's consider bending of a cantilever beam and I fix it in this side. I am going to bend this by applying a force. If we perform a static analysis, as the stress value increases throughout the simulation, we get a final stress contour. This final stress contour can be relayed upon while the intermediate results produced by the pseudo time stepping of the solver cannot be relayed upon. This is not the case with the dynamic analysis. Here, if you apply a same load on the cantilever beam and perform a dynamic analysis, you can see how gradually the stress increases.

And at each time step at one second, two seconds, that is if you want to look at the stress result at the end of five seconds, the results prior to the final step, that is the first second result, will be reliable as well. Hence, the dynamic analysis requires more computational effort than a static analysis. So, depending upon our requirement, we tend to choose either we want to perform a static analysis or a dynamic analysis. And finally, to put it short, if someone is interested in looking at the deformation at the end of loading, so they can just perform a static analysis, look at the final deformation.

If you are interested in looking at how the deformation progresses, you can perform a dynamic analysis or not. Now, let's get back to the slides. As discussed earlier, any material will have an elastic region beyond which it is going to behave non-linearly and finally end up in the failure zone. Hence, to capture all these non-linearities, we do have specific types of analysis that is classified as linear and non-linear. In order to capture the non-linearities in a static or dynamic analysis, we have specific analysis types to differentiate between these loads.

So, to understand it in a better way, let's open SOLIDWORKS. Click on File, open a new part. Make sure the unit systems are as per your requirement. Now, click on the front plane, right-click, and Edit Sketch. Draw a rectangle using the Corner-to-Corner method. Use the Smart Dimension to input 50 mm and a 50 mm for both the length and the breadth. Click OK. Now, select this circle. Place it exactly in the center point of both the sides. Dimension it as 10 mm and click OK. Now, in order to constrain this circle into the center of the circle, click on this dimension.

Then, select this side and choose this point here and input a value of 25 mm. Similarly, choose this side and select the center. Input a value of 25 mm. Now that we have fully constrain this geometry, click on the Features here and select the Extrode option. Input a value of 5 mm and click OK. So, now we are going to perform a static analysis on this part and understand when we need to perform a non-linear analysis on such a simulation. So, this finite element analysis on a plate with a hole is a basic problem that any FEA engineer would start with while learning a software.

So, let us proceed with the simulation. Click on Simulation. Choose a new study. Let us perform a static. Click and click OK. Now, for the material, let us select the Alloy Steel which is the default material. So, the yield strength is about 620 MPa. Click Apply and Close. Now that we have defined the materials properly, right click on the Features, select the Fixed Geometry and choose this face. Make sure you choose the face and not the edge here. Click OK. Let us apply a load on the other face.

Select the face. You can see if you apply the load now, it is going to be a compressive type of force. We are interested in applying a tension force. So, input a value of 1000 N and reverse the direction. Click OK. So, let us use the default mesh for the demo purpose. So, click on OK. So, this is our meshed model. This looks fine. Let us proceed with the simulation and run it. OK. Now that our simulation is done, let us look at the results here.

You can see the yield strength is about 6.2 into e power 8. The stress values are well below this yield strength value. So, this stress result is acceptable. Since there is a linear relation between the stress and the strain within the elastic limit, if you increase the force by a factor of 10, your maximum one measure stress should also increase by a factor of 10. So, right click and run the simulation. So, as you noticed that there was a similar change. So, now let me increase the force value by a factor of 10 and rerun the simulation.

So, you can see in the legend, so we have a arrow pointing to the yield strength value. Thus, any value that is being plotted above this yield strength value is unexpectable. That is, we have to perform a nonlinear analysis to get realistic values from this simulation. Hence, in any case, if you are performing a static analysis and your stress values are above the yield strength value, you should not use those values. You need to switch over to a nonlinear analysis to get reliable results. Let's copy the same simulation and perform a nonlinear static analysis.

Click OK and run this analysis. You can notice that the solver is taking much longer time than it took to solver's static analysis. And here you can see the strain values are not as high as the static analysis. That's because, if you consider the stress-strain graph, if the relation between the stress and strain is linear, you can see the displacement gets larger as the stress value increases. Hence, in the static analysis, our solver followed this extrapolated path, such that for any value of load that we give, it received the corresponding stress and strain by just extrapolating this curve.

Part 2

Hello Friends, SOLIDWORKS के FEA वीडियो में आपका स्वागत है. इस वीडियो में हम Static Analysis के बारे में डिसकस करेंगे और डिसकस करेंगे कि ये Dynamic Analysis से कैसे अलग है. SOLIDWORKS में कितने परकार के Analysis अवेलेबल हैं और उन्हें कब इस्तमाल किया जाता है. चलिए PPT से स्टार्ट करते हैं. Structural Analysis का Structure Term खाल समझने के लिए हम Finite Element Analysis को Perform करते हैं ताकि हम Behavior को समझ सकें. यहां शुरुवात में Finite Element Analysis में Unknown Displacement ढूंडा जाता है. और फिर Reaction Force और दूसरी Drived Quantity जैसे Stress और Strain पानी के लिए उसे वापस से Resubstitute किया जाता है.

Basically Structure Analysis, Problem को Static Analysis और Dynamic Analysis में Classify कर सकते हैं और यह Load पर Depend करता है जो कि उस पर लग रहा है. इस Classification के अलावा 1D, 2D और 3D में Finite Element Analysis है जिसका Classification Used Material पर Depend करता है. हमारे पास कई अन्य Specific Analysis हैं जैसे की Buckling Analysis, Fatigue Analysis जो कि उस Purpose को पूरा करते हैं जिसके लिए वो बनाए गए हैं. हर एक Special Analysis के लिए SOLIDWORKS के पास Separate Modules हैं. चलिए अब हम Analysis का Basic Classification करते हैं जो कि Static Analysis और Dynamic Analysis है.

अगर आप Static Analysis को Consider करते हैं तो हम एक Force Assume करते हैं जो कि Model पर Act करता है. वो क्वासी Static है. दूसरे शब्दों में Loads जो Model पर Act कर रहा है वो इस तरह Gradually Increase हो कि Acceleration Velocity Neglected की जा सके. जबकि दूसरी तरफ Dynamic Analysis में सिर्फ Inertial और Dumping Effects को Consider करेंगे. इससे पहले कि हम Stress और Strain Find Out करें, Components के लिए Acceleration and Velocity Solve करते हैं. Static Analysis के Comparison में Dynamic Analysis ज्यादा Time Consume करता है. अगर आप Static Analysis को भी Consider करते हैं तो आप Point A से Simulation स्टार्ट करेंगे और B आपका Final End होगा. जो भी आपको Intermediate Result मिला है, आप कोई भी Path को Follow कर सकते हैं और Final Result प्राप कर सकते हैं. इस तरह आप कभी भी Static Analysis क Intermediate Value पर Relay नहीं कर सकते हैं. दूसरी और Dynamic Analysis में अगर आपके पास Two Destinations हैं, अब हम उसके Path Possess करते हैं Intermediate Value जो की Stress और Strain से मिलती है. वो Reliable होती है और उनका Use किया जा सकता है. चलिए अब और Specific करने के लिए Consider करते हैं, Cantilever Beam को Band करते हैं और इस Side को Fix करते हैं. अब ये Force Apply करके मैं इसे Band करने जा रहा हूँ. अब Static Analysis Perform होगा, जिससे Summation के Throw Out, Stress, Value Increase होगे. इसमें हमें Final Stress Control मिलेगा. Shudo Time Stepping के द्वारा Intermediate Result प्रोड्यूस होगा, जिससे इस पर Solver Relay नहीं होगा. Dynamic Analysis के Case में ये संभव नहीं है. अगर आप यहां Cantilever Beam पर M-Load करते हैं और Dynamic Analysis को Perform करते है अब हम देख सकते हैं कि हर Step पर Stress Gradually Increase हो रहा है. प्रतियक समय Step पर 1 Second, 2 Second, अगर आप देखें तो Stress Result आपको End के 5 Second में प्राप्त हो जाएगा. Final Step के लिए First Second Result Reliable है. Static Analysis के Compare में Dynamic Analysis को Computational Effort ज्यादा Require हैं. जहां हम Perform करना चाहते हैं, ये हमारे Requirement पर Depend करता है. हम Static Analysis चूज करें या Dynamic Analysis. अंत में इसे छोटा रखें, यदि कोई Loading के End में Deformation को देखने में Interested है, वो सिर्फ Final Deformation पर Static Analysis को देख सकते हैं. यदि आप ये देखने में Interested हैं कि Deformation कैसे Progress करता है, तो आप Dynamic Analysis perform कर सकते हैं. अब हम पिछली Slides में चलते हैं, जहां हमने Discuss किया था कि कोई भी Material Elastic Region के Beyond हो जाता है, तो वहां पर Non-Linearly Behave करेगा, और अंत में Inner Failure Zone End Up हो जाता है. इसलिए इन सभी Non-Linearities को Capture करने के लिए हमारे पास Specific Types हैं. Static या Dynamic Analysis में Non-Linearities को Capture करने के लिए इसे Linear और Non-Linear के रूप में Classify किया गया है.

InLoad में Differentiate करने के लिए हमारे पास Analysis के Specific Types हैं. तो इसे बेहतर तरीके से समझने के लिए हम SOLIDWORKS खोलें, फिर File पर क्लिक करें और एक New Part खोलें. ध्यान दे अपने Requirement के अनुसार Unit System हो. अब Front Plane पर क्लिक करें, Edit Sketch में Right क्लिक करें और Rectangle Draw करें. Corner to Corner Method का यूज़ करें. अब Smart Dim Dimensions को यूज़ करके 50 mm Length और 50 mm Breadth Value टाइप करें. फिर OK पर क्लिक करें. अब Circle को Select करें. दोनों साइड के Dimensions 10 mm रखें और Exactly Center Point पर Place करें. फिर OK पर क्लिक करें. अब इस Circle को Center के Order में लाने के लिए Constrain करें. अब Dimension पर क्लिक करें. इस Side को Select करें. और अब यहाँ पर इस Point को Choose करे और 25 mm Value टाइप करें. और Similarly इस Side को Choose करें. Center को Select करें. और 25 mm Value इनपुट करें. अब हमारे पास यहाँ Geometry Fully Constrained है. यहाँ Features पर क्लिक करें. फिर Extrude Option को Select करें. और 5 mm Value टाइप करें. और OK पर क्लिक करें. इसलिए अब हम इस Part पर एक Static Analysis करने जा रहे हैं. और समझते हैं कि जब हमें इस तरह के Simulation पर एक Non-Linear Analysis करने की आवश्यक्ता होती है. तो Hole के साथ यह Finite Element Analysis एक Fire Plate पर मूल समस्या है. जो किसी भी Engineer को Software सीखते समय शुरू हुई होगी. अब Simulation करते हैं. Simulation पर क्लिक करें. फिर New Study को Choose करें. चलो Static Perform करते हैं. और OK पर क्लिक करते हैं. अब Material के लिए Alloy Steel को सेलेक्ट करें. जो की Default Material है. तो तुरंत 620 Megapascal एपलाई होता है. और अब Close पर क्लिक करें. जो Material हमने डिफाइन किया था. उसके Fixtures पर Right क्लिक करें. Fixed Geometry को सेलेक्ट करें. और इस Face को चूज करें. ध्य दूसरे Face पर एक Load Apply करें. और उस Face को सेलेक्ट करें. जिसे आप देख सकते हैं. यदि आप Load Apply करते हैं. तो ये एक Compressive Type of Force हो रहा है. हम एक Tension Force को लागू करने में इंट्रेस्टेड हैं. इसलिए 1000 Newton Value Input करें. और Direction को Reverse करें. फिर OK पर क्लिक करें. Demo Purpose के लिए Default Mesh का Use करें अब OK पर क्लिक करें. और ये हमारा Mesh to Model है. और ये दिखने में अच्छा लग रहा है. तो Simulation को Proceed करते हैं. और फिर Run करते हैं. अब हमारा Simulation Complete हो गया है. अब Result देखते हैं. तो यहां हमें Yield Strength 6.204E plus 8 Stress Value कम है. तो हम Value Input नहीं करते हैं. तो Stress Result Acceptable है. Elastic Limit में Stress और Strain में Linear Relation है. अगर आप Force को 10 Factor से बढ़ाते हैं. तो आपका Factor 10 से Maximum 1 Magisters Increase होगा. फिर Right Click करें. और Simulation को Run करें. आप देख सकते हैं कि यहां Similar Changes हुआ है. तो अब Force Value को Factor 10 से Increase करेंगे. Simulation को Rerun करें. तो आप Legend में देख सकते हैं कि हमारे पास Heal Strength के लिए Higher Appointed Value है. अगर हम इस Yield के उपर कोई भी Value Plotted करेंगे. तो वो Value Unacceptable होगी. इसलिए हम Simulation से Realistic Value निकालने के लिए Non-Linear Analysis को Perform करेंगे. इसलिए किसी भी Case में यदि आप एक Static Analysis कर रहे हैं और आपकी Stress Value Instant Value से उपर है. तो आपको उन Value का उपियोग नहीं करना चाहिए. जो Reliable Result प्राप्त करने के लिए Non-Linear Analysis करने में Switch Over हो जाते हैं. अब Same Simulation को Copy करें और Non-Linear Static Analysis को Perform करें. अब OK पर किलिक करें और इस Analysis को Run करें. आप Notice कर रहे होंगे कि Solver ज्यादा समय ले रहा है जितना ये Static Analysis को Solve करने में लेता है. यहां Static Analysis के Compare में Strain Value High नहीं है. अगर आप Stress Strain Graph consider करते हैं, तो Stress और Strain क Relation Linear होगा. आप देख सकते हैं कि जब Stress Value Increase हो रही है, तब Displacement Large हो रहा है. और जब आप Non-Linear Region Enter करते हैं, Displacement Increase होता है. मगर Stress Value उतना Increase नहीं हो रहा है. Static Analysis हमारे Solver ने इस Extrapolated Path को Follow किया है. ताकि Load के किसी भी Value के लिए, जो हम इसे देते हैं, वो इस Stress और Strain को इस कर्� Extrapolating करके प्राप्त कर लेता है.

Want the rest of CAE Simulation using SolidWorks?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full CAE Simulation using SolidWorks course

The remaining 6 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full CAE Simulation using SolidWorks course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.