← Course overviewFree lesson 1 of 3 · lesson 1 of 42Next lesson →

Unlock all 42 lessons of Automotive BIW Design and Development Part 2 using NXCADFull course ₹40,000 · paid

Price & syllabus
Free lesson · 42 min · no payment

Rear Door Design Rules and Flange Cross Sections

A free lesson from Skill-Lync's Automotive BIW Design and Development Part 2 using NXCAD course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Week 1 - Backdoor Session 1”

What will you learn in this free Automotive BIW Design and Development Part 2 using NXCAD lesson?

The instructor explains the parts of a tailgate: inner panel, split outer panel, hinge, gas stay and latch reinforcements. The lesson then walks through eight flange cross sections and the rules behind them, such as 15 mm for spot welding, 7 mm for laser brazing and a 3 mm plus thickness bend radius.

  • Tailgate parts and why the outer panel is split
  • Hinge placement and the door opening trajectory circle
  • Flange sizes for spot welding, hemming and sealant
  • Minimum bend radii, draft angle and mastic points

What comes after lesson 1?

The next free lesson is lesson 2, “Rear Door Case Study: Aluminium Cast vs Steel Deep Drawn” (20 min). Later in Skill-Lync's Automotive BIW Design and Development Part 2 using NXCAD course (paid): lesson 4, Week 2 Backdoor Session 1; lesson 5, Week 2 Backdoor Session 2; lesson 6, Week 2 Backdoor Session 3. The full course has 42 lessons (23 h 41 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

Hey guys, welcome back to our course on Body and White Design. In week 11 of our course, we are going to learn about the designing of the back door and also how to approach the modeling of the back door in the NXCAD software. In this week, we will be looking at the various design and the functional requirements of the rear door or the back door or also it's called the tailgate. We also will be looking at the rear visibility and the rear crash regulations and the most important criteria to be considered while designing the hood will be the ceiling and its function throughout the rear door.

We also will be looking at various manufacturing and joining techniques and we also have the hinge, the latching striker and also the gas stay or the power lifter. Now it's electronic nowadays. We also have all these in the rear door similar to the hood. So here we have the exploded isometric view of the rear door. You can see the upper, the outer, lower. We have the inner panel. We also have various reinforcements similar to the hood. So as you can already see, the back door is not just one piece of sheet metal or just one component put together.

It has various components and we'll also be looking at two different approaches for the back door that is the steel and the aluminium approach. So let me first give you a heads up on all the major parts of the rear door. We have the inner panel in green. As you can see, it is one single piece. We also have the outer panel, but the outer panel here is interesting. It is not in just one piece. It has divided into two parts. So separation of the outer panel becomes one of the major concerns.

Why? Because this is going to be done based on two factors. One is going to be the position of the headlamps. So here you have provision for the rear lamps and also the position of the number plate because the number plate is usually a flat component and it cannot be mounted on some place that is curved. So this place obviously has to be flat and the outer panel is going to be divided into two based on these two factors. Also, we have a lot of reinforcements here.

We have reinforcements for the hinge. As you can see, these in yellow. And we also have the reinforcements for the gas stay or the electronics stay which is being used nowadays. And then we have the Lagenstreicher reinforcement. And also we have a reinforcement here for the wiper motor which will be used for the rear windshield. As you can already see, there are a lot of embosses in the outer panel upper. Why is it so? Because usually the outer panel is going to be a styling element.

It is not going to be the muscle of the entire component. So you can ask me, why am I seeing embosses on the outer panel? Here, we are going to be having spoilers. So this particular tailgate of an SUV is going to have spoilers. So in order to mount the spoilers, we have embosses here. And they are going to be snap fitted to these outer panels. That's why we have the embosses along with the holes here. Now let's talk about the inner panel. As I already mentioned, we have a lot of reinforcements and also embosses for the same.

They are for the hinge, the gas stay, and also for the Lagenstreicher. Similar to the hood, the tailgate is also going to be opened and closed many a times. For that purpose, we have the hinge and also Lagenstreicher. Also here, we are going to do the same trajectory circle. We are going to maintain the perpendicularity with respect to the Lagenstreicher also. Now let us head to the modeling software and learn the basic approach towards designing the tailgate. So here, we have the entire styling of the car and also the tailgate integrated to it.

The first thing to remember when designing something, be it a component or a sheet metal design, is to not disobey the styling which is being given by the styling team to us. This is the first thing to be kept in mind. Now, let me hide the styling for a moment. Here, we have the entire assembly of the rear door. As you can see, we have the spoilers here. The spoilers are split into three. The spoilers side left, right, and the middle. So I will hide all of these because the spoilers are usually just plastic components and we are not going to concentrate much on them.

Now, here we have the outer panel upper and the outer panel lower. I will hide the outer panel lower for now. As you can see, we have embosses and holes on the outer panel upper for mounting the spoilers. I will hide the outer panel upper as well. Here, we have the windshield. We will come back to that later. Now, as you can see, this is our inner panel. The first thing we will be doing when we get our styling from the styling team is that we will first design the embosses, which means we are not going to model the emboss in the NXCAD software, but we are going to decide the position of the embosses.

How do we do that? Now, you have the embosses, I mean the hinge here. I will hide the hinges for now. Yes, as you can see, you have the pivot here. Now, in this view, if I take a cross section along the Y at 0Y, that is at 0Y, this will be the center section of our rear door. Now, I will go back to this and I will change the value to 310 and I will show you this. Now, we have come to the center point of the hinge emboss and also the hinge as well.

As you can see, if I take this side view, this is going to be just one circle and the center point of this hinge is going to be connected to the center point of the other hinge on this side. So, when I join these two, I am going to get the hinge axis. And with respect to the hinge axis, I will draw a line to the center of this striker. So, once that line is drawn, we will draw the circle and we will get the trajectory.

So, that trajectory circle will be the path that the rear door follows while opening and closing. And, please make sure that this is perpendicular to the circle. The striker is going to be perpendicular to the circle. Now, coming back to the position of the hinge emboss. As you already would have noticed, I mentioned the value 310 mm. Why is that so? That is because from the 0Y region, I am positioning the hinge emboss 310 mm away. So, why is this so? As we already learnt in the hood, the hinges should be as far as possible from each other and also towards the edge of whatever component they are connecting.

Why is this so? Let us take a simple example, hoping that you are looking at your laptop. Please look at your laptop hinges right now. As you can see, the hinges are going to be towards the edge, towards the edges of both the upper and the lower panels of the laptop. So, only if this is being modeled, I mean, if this is being designed at the early stage, can the designer actually decide upon the weight and how the entire design is going to flow? Because, we have a gas stay to open the rear door, but the force of the gas stay and also the weight of the rear door, that is somewhere around 8 to 10 kgs, is going to be closed by the human.

If the hinges are going to be at the center, here, then it is going to be really tough for the human and more forces is going to have to be applied in order to close the rear door. Now, let us get back to the value of 310 mm. So, why did I position it at 310 mm? When I say 310, I mean the center position of the emboss or the center position of the hinge itself. Why is this so? Because we have a car which is approximately 1 meter in track width.

So, the roof and the rear door is going to be approximately 630 to 660 mm in width. So, when I assume this, what I want to do is position the hinges as far as possible. So, from the midpoint, it has to be somewhere around 300 to 330 mm away. So, that is why we have chosen 310. You can choose the most appropriate value you feel is going to be correct for this. Also, let me illustrate another example for you. I hope you have an access to a door nearby.

So, go to this door and you check where the hinges are actually positioned. You always see two hinges that are far away from each other towards the edges of the door, the top and the bottom edges of the door. In the middle, we have more hinges for the doors because they are really long. The length is really big. That is why we have a lot of hinges in the middle. But for the rear door and a car, we just need two hinges that are going to be at the extreme edges similar to a laptop.

Now, when we head to design the inner panel, let's first hide all these reinforcements. We'll get back to these later. Now, let's take the middle. I'll just type in zero here. So, this is a zero way region. And that was the minus 310 by region. Now, when we start designing the rear door, what we have as input from our team is a rear door from our previous car and also we'll be having the styling. So, with these, we have to move forward with what we are going to design.

So, as similar to the other components, we need master section for the rear door. But here, we are going to create our own master section and we're going to understand the various dimensions that we use in the master section. Yes. Now, the first and the most important functionality of the rear door is the design functionality of the rear door is going to be this flange. As you can see, it runs through till the end of the rear door. Let me show you the rear view. So, here, this flange is really important because only below this flange, there will be rubber sealant which will help close the rear door.

Now, what I want you to do is. Go to a car, be it any car, open the rear door, and you'll see this black color lining that runs throughout the enclosure area of the rear door. So our first agenda is to understand and learn the cross section at various regions. Say the 0Y on the top, the 0Y on the bottom, and also other critical areas. What do I mean by critical areas? So here we have a corner here. We'll take one cross section here, and also take another cross section here.

So that is going to be four cross sections, and also we have the hinge here. So we'll take one there and another here. That will be six cross sections, and we need two more cross sections. Why is it so? Let me first unhide the styling here. If I unhide the styling, you can see the position where the rear lamp is there, there's a curvature. So, yes, here we have the rear lamp, and so above and below this rear lamp, we'll take two sections. Exactly here, and here.

We'll study the cross section or the mass section of the flange at these eight sections that I just mentioned. Now, let's go to the first. So, we already I'm in the 0Y cross section region. So, we'll take this. I'll take this view, and here we have the cross section for the mid 0Y region. Let me unhide all the components here. We have the windshield, upper, and the lower. We don't need the lower right now anyway. Yeah. So now, as you can see, here we have the entire cross section.

We have the windshield here, the spoiler, the inner panel, and the outer upper. Now, as you can see, the inner panel and the outer panel are joined together by the hemming process. This we've already learned in the hood. Again there is this small tolerance between the hem. And then, as you can see, the outer panel, so this is the outer panel, and this is going to be the styling of the outer panel. So, every component that we design, the outer panel is going to be thickened in the downward direction.

And then, okay, let me annotate. So let me take a picture of this. Now, so here, you can see the inner panel here, and also the outer panel. Now, here, the outer panel is here, and the inner panel. So the outer panel is always going to be thickened in the downward direction, and the inner panel is going to be thickened in the upward direction. Now we have a thickness of 0.75 mm, and we have a distance between these two to be 0.2 mm. So every time you see a 1.7 mm offset, it is going to be twice 0.75, that is 1.5, and then add 0.2 distance to it, that will be 1.7.

Now let us move on to the rest of the dimensions and study the cross section. So here, you can see there is a distance, and this is going to be a minimum of 35 mm. And why is this so? Because we are going to do hemming. This place cannot be used for spot welding. Now we have this depth. This depth will also keep it as 35 mm. Again, why do we need this depth? Let me minimize this. Here, as you can see, at minus 310, we will be having the hinge emboss.

Okay, the emboss is now hidden, but we will be having the embosses here. And for that, and also a bit of clearance, we need a minimum of 35 mm. Now let's go back to this. Here we have the horizontal flange, and this we need a minimum of 25 mm. Why is it so? As I already told you, this flange below this will be having the rubber sealant, which I asked you to see in every car. So that flange, let me annotate and show you, when it is in the compressed position, it is going to be spread out to a distance of 25 mm.

And when it is in the upward position, say, please assume this is the rubber flange. It is going to be like this approximately when it is not compressed. And when this is going to be placed on here, when it is when the rear door is shut, it is going to transform to something like this. And this is what we have here. Okay, hope you understand this. So that is why we have this 25 mm distance for this horizontal flange here. And why do I have this step here, sir?

That is the next question you'll be asking me. Now let us assume two sheets. Now one sheet has one straight line like this and the other has a step like this. So which will be more stronger? Obviously the one which has a step. That is the exact reason why we have step added to this flange here. Now, as I already mentioned, we have a depth of 35 mm and the same will be used here based on the curvature. It might vary because only here we have the embossed and here we don't have the embossed.

Now what will be the angles here and here? As I follow this for all the parts, the opening angle for any sheet metal has to be a minimum of 5 to 8 degrees. So why is it so? So if it is in the negative draft angle, the tool will not easily come out and wear the tool much more than if it is 5 or 8 degrees. Now what should be the radius that I give here the inner and the outer radius for this? I'll take I'll illustrate here.

So let's say we have two radii here. Okay. So this is my outer radii and this is my IR, inner radii. So what is the most common mistake that people make? If you make this mistake as a sheet metal designer as a rear door designer, then the analysts people are going to simply laugh at you. Now what should my IR and OR be? So we already have this VEDA that we actually have to follow while designing sheet metals that is going to be 3 plus thickness.

So what is that? That is 3 mm plus the thickness. Say we have a thickness of 0.75 mm for the outer panel and the inner panel here. So wherever we use our outer radius has to be 3.75. So that our inner radius is 3. If our outer radius is 3, then the inner radius will go to 2.25 which is wrong. So please make sure you use more than 3, I mean a minimum of 3 if it is an inner radii or a minimum of 3.75 if it is an outer radii.

Please never forget this while designing any other sheet metal component, especially for the rear door. Now let us go back to this flange and now here we have this additional flange here and this is a spot where it is connected to the outer panel. Here as you can see, it is spot welded. So what will be my distance? As we already learnt in the roof, for spot welding, we need a minimum of 15 mm distance. Okay, now it is 15 mm distance. Why shouldn't I increase it or decrease it?

If I increase this, either this is going to reduce or this is going to increase. Now we don't want that to happen. Why? We look at it when we look at the rear door and the roof together, which will be seen in a very short time. Now, also apart from spot welding, we'll be having another extra plus 5 mm here. Now why is that so? For that the reason is that we are going to place the windshield. So this will be our windshield. This is our windshield here.

And the windshield is going to be placed on this metal piece. So whenever a glass is going to be placed on a metal piece, it is not going to stay there without either the windshield getting damaged or the sheet metal getting eroded. So what should we do? We should always place a rubber sealant there. Similar to what we use here is going to be placed there and similar to what we saw in the roof. That is how the rear windshield is also going to be positioned here.

Yes. Now, you may ask me, so why do I need 15 mm here for spot welding because spot welding is going to be at one spot. So we got this questions from many of the students. So let's say this is a sheet metal. This is a spot that is going to be spotted. So the probe is going to be something like this. But the gun that we use is going to be much bigger. So in order to accommodate this gun, which is going to be a maximum of 15 mm.

That is why we need a minimum 15 mm flange, where are we going to spot weld. Now again, if you notice, we have a clearance here that will be a minimum of 5 mm. So why do we have the clearance even in the design? So this is the styling that we get for the windshield and we have the spoiler and the inner panel. Even in the design, we have considered 5 mm clearance. Why is it so? So as I already mentioned, this extra space for the rubber sealant that is going to be placed between the metal part and the windshield.

That 5 mm clearance is required to place that rubber sealant between the windshield and the metal part. Now let's get to why this is so wide. As I already mentioned, this is going to be 25 mm. This is the yellow line that I've drawn here. It is going to be just 25 mm plus this and then below this we will be having the rubber sealant which will initially be here and in the closed position it is going to be converted to this shape. So why is it more than 25?

So here we have approximately 35 mm and it is going to decrease as it goes to the corner. We will get back to that later. Now why is this so wide? And it is not at the minimum. It is not at the minimum. So, for any cross-section, let us take this cross-section and in this software, we will be considering the moment of inertia as we already saw in the roof part. So, any part that is wide enough has more moment of inertia than some other cross-section that is narrow.

This is a thumb rule. So, in that case, you can ask me, so, why don't we simply go on increasing this to like, you know, to this space and then do the hemming somewhere here. No, because this is a styling that is given by our team and our ultimate agenda is to obey the styling and get our engineering part done within what the styling provides us. Now, the upper cross-section is completed. Let's move on to the other cross-sections as well. So, as I already mentioned, this will be a second cross-section at OY.

If I take this view, it's not clear. So, I'll take an isometric kind of view. Now, here you can see, until this part, the cross-section is the same. Yes, the flange follows the same cross-section throughout and here it changes. As you can see, we have embosses here. The reasons for these embosses I'll explain shortly. So, it is just going to be a flat face for somewhere about 80 to 110 mm. Why do we have this provision? So, as we already mentioned, there's going to be a reinforcement for the latching striker and the latching striker is going to be mounted.

So, we have an embossed reinforcement for here to provide additional strength locally. Now, the major purpose for this flange right here, apart from what we saw in the top cross-section, is that when we take this view, this will be the lowermost part of the rear door. So, we'll be having holes on this surface, you have to design holes on this, which will act as drain holes. Other than that, the same fashion is going to be followed, the same hemming is going to be there, similar to what we saw in the previous cross-section.

Let us take a cross-section here, in the corner. So, you can ask me, what difference does it make when the, you know, fashion is going to be the same. You have the same cross-section being followed here. Let me go to edit section and I'll increase the distance to 400. Yes, as you can see, the cross-section here is the same, the exact same, except that it is going to take a turn. So, what should we consider while designing this? So, I'll have a cross-section here, and another cross-section here, as you can see.

So, when I connect a bridge curve, and when I connect these two, I should make sure that there is a smooth transition, and a smooth curvature. If not, what will happen? So, that is our main question. So, I wanted to assume this. Let us take a rubber wire or something like that. Take a phone charger or your laptop charger wire. So, if you bend it to a larger radius, say 100 mm, it will not, you know, deteriorate so easily. But when you bend it to an exact U, like 5 or 10 mm radius, it is going to break.

That is, it is going to work, and it is not going to stay as it was intended while designing. So, for that reason, we should have, there is a minimum radius criteria that should be followed when we are doing curvature for this flange. So, what should be the minimum radius that has to be followed while having a curvature on the sheet metal parts here? It should be a minimum of R40 to R50, that is, 40 mm to 50 mm radius. Now, if you notice, this flange right here, here it is going to be 35 to 40 mm in length.

As you can see, as it goes here, it is getting reduced. So, what we said earlier, there has to be a minimum of 25. So, obviously, the 25 mm criteria is being followed here, but what is the reason that we have reduced it here? Now, let us go to this view. Yes, as you can see, we have the spoilers and the windshield. And the windshield takes such a lot of space to increase the visibility criteria because the windshield also has headliners, as we have already learned.

Now, let me hide the spoiler for now. Now, as you can see, clearly, here it is larger and here it is smaller. The 35 here, it becomes 25. If this was usually as usual as 35, this would have gone in, the visibility criteria would have gone down. And also, the spoiler design would have been affected. Because the spoiler, again, it is a plastic part and an aesthetic element and it cannot be modified or this cannot be neglected while designing the flanges for the inner panel. Again, as you can see, let me hide the outer lower.

The 25 mm is being followed throughout till here. Why is this so approximately here? We will be having the rear lamp and for that, there is a curvature here. So, in order to accommodate this curvature and as well as these embosses here, we have reduced it to 25 mm. So, this is a reason for all the cross sections that we saw earlier. Based on this, the first thing that we will be doing while we model the rear door will be to create this flange throughout. And then, we will move on to create this entire surface.

Now, on the rear door, we have a lot of embosses. So, this is the most interesting part. You would have wondered since the beginning of the video and I haven't explained it yet. Now, let's get to this. So, you can ask me, so why do we have all these particular and specific shapes? And we have a lot of embosses, many embosses here. So, let me explain them one by one. As we have already said, these are holes for the embosses that are going to be here along with the reinforcement for the hinges.

So, these two are done. And here, we have the embosses for the gas tape. Yes, as you have already noticed, the rear door or the tailgate is going to be a symmetric component except for certain very small and specific features like these holes and this wiper motor emboss. Other than that, the entire thing is going to be almost, I can't say it is completely symmetric, but it is almost symmetric. Let's move on to these embosses. So, as you can see, we have the V or the Y shape.

Why is it so? So, when we take the car from the rear direction and when we view it, when there is a rear crash, what happens is the forces are going to attack this particular point. That is the latching striker point. So, what has to be done? So, this force has to be resolved in the outward direction. So, for that purpose, similar to the hood, we have a V or the Y embosses here. Also, we have various holes. So, why do we have these holes? Now that I've created the emboss, now you can ask about the shape of the emboss, but this shape varies from one design into another.

And it can vary depending upon the CAE, but this does not have any aesthetic value because no person or no customer is going to look at the inner panel. What I will be seeing is the outer panel and the spoilers only. Now, let's move on to these holes. Why do we have these holes and why do we have two holes here? Two, there are two reasons for these holes. One, this hole has to be as big as possible to actually mount the rear lamp. Because, once we have the inner panel and the outer panel hemmed together, there is no way that we are going to, you know, introduce the rear lamp from the outside.

It can only be done from the inner side so that we have these holes. You also have these mounting tabs. So, I have created one hole here. And the same has to be reciprocated for, this is also for the rear lamp. And the other reason is going to be for, is to balance the weight on either side. Now, certain models nowadays don't have gas days, instead they have electronic opening and closing of the rear doors. For that, we can have motors mounted through this hole. Also, this will be the wiper motor mounting region and the embossed and the reinforcements are going to be here.

So, we have the holes here and this is one big hole. So, why do I have this hole? As you can see, this is a symmetric hole, but this has to be big enough for me to position the axis of the wiper motor. Now, the same has been reciprocated here and you have a law extension here. So, what is the purpose of this flange that I have created here? For that, we will get the outer lower and the outer upper. Okay, let's take these cross-section and 0y.

Yes, now, as you can see, these two are going to be joined together, but there is a 5mm distance between these, the outer panel and the inner panel. Why is it so? As you already saw, similar to the hood, the inner panel and the outer panel here are going to be hemmed. But, the rear door itself is a really huge component that there is going to be a lot of vibrations, if not for this center connecting part. So, how are we going to connect here? We cannot do a laser bracing or we cannot do spot welding here.

Why is it so? If I do a laser bracing or a spot weld, this is going to affect the aesthetic value of this region. And this is one of the most important regions where we have the number plate and the person is going to look at this place. So, we have mastic points between these two and this has been proved to actually reduce the vibration and actually cancel out the noise. We cannot actually cancel out the vibration. There is going to be vibration, but the noise is going to be canceled out.

The person will not hear any noise, even if there is some amount of vibration. Next, what should we look at? I'll edit this. No. No. No. We have embosses here and here as well. So what are these embosses for? As I already said, we have the rear lamps, we have the electrolyzed motors, we have the electrolyzed stay or the gas stay. And for those components and wire harnesses, these holes are provided. And there are mounting points here, which can enable them to be mounted. And also, for electrolyzed or motorized closing mechanisms, we need the power switch, which will be mounted here.

The next question you may ask is, why have I positioned this flange in a particular, a specific, you know, position? So there is a reasoning. If I take the side view, you can see that this is the exact center between the uppermost point and the lowermost point. So this will enable us to actually reduce the vibration at the center because in the corners, they are being hemmed to the outer panel. Now, let's go to the last emboss that we have here. So why are these positioned and what is the purpose of these embosses?

So every car will have a drip panel just before the inner panel. So in order to mount the drip panel there, we have these embosses. We have six embosses for the drip panel alone. Now, let us again go back to zero by region and I'll unhide all the reinforcements. Yes, now let us understand the designing methodology for the reinforcements. As you can see, the reinforcement has one flange here and another flange on the top. So this is for the emboss for the hinge emboss here. So you can ask me, why don't we extend it to this space?

So the reinforcements have to be connected to the inner panel in one way or the other side, right? So how are they going to be done? They can either be welded, that is spot welding, they can be laser braced or they can also be hemmed. There are three possibilities. It again depends on what material we use, how the designer wants it and how the manufacturing facility of the production center allows it. If there is no provision for additional hemming or additional laser bracing there, then we cannot do it.

We have to take all these into consideration and then the designer makes the final decision as to what has to be done. Now, the designer who designed this rear door has assumed or is going to actually is going to spot weld this reinforcement to the inner panel. Why am I using spot weld here and why am I not using any other thing? Because this is going to be the inner panel. The outer panel is going to cover all of these and no customer is going to take a look at this and assuming that this welding is going to cost me much lesser. If not, so what else can be done?

So this flange can be extended till the end and it can also be considered during hemming. It can be hemmed along with the inner panel in the outer panel, correct? The other thing that can be done, we already know that the inner panel on the inner side is going to be spot welded. Let me hide the unhide this. Yes, as I already said, here we are going to do a spot welding. Here we are going to do hemming. So this can be extended till here and it can be hemmed or this can be extended on the other direction and it can be spot welded on the inner side.

Either of them can be done. The same applies for the gas reinforcement on the other side as well. Yes, here we don't have any other choice. We cannot do a hemming here. So we have to do a spot welding for this reinforcement. Also, how do I constrain the position of these reinforcements? As you already have seen, we have the hinge here. So that when we mount the hinge, it is going to position the reinforcement. The same goes for the gas day and the wiper motor as well.

Also the latch, it has to be bolted, but once in the close position, it is not going to move. So now we have taken a close look at all the features of the inner panel of the rear door. We have taken a look at all the reinforcements, the outer panel, the spoilers, the various cross sections that are going to be followed. We spoke about eight cross sections to keep them in mind when you design the flange first and then we'll move on to all the embosses and then we'll create the additional embosses in the top and the bottom region.

We'll give the embosses, the provisions and the reinforcements. We'll plan if you're going to hem them along with the outer panel or spot weld them along with the outer panel on the inner side of the inner panel. Now there's one more additional component that we haven't talked about since the beginning of this video that will be the windshield. So here as you can see, the windshield is going to be placed on the inner panel and it is one of the components of the rear door assembly.

So as you can see, only this white region that you see is going to be the rear visibility of the passenger who is sitting inside. So what are these? They are the gradient lines. So only and only if my let me hide this first. So only if this is going to be reduced to 25 mm here, can I have a wider windshield glass to be mounted and also this will increase the rear visibility criteria. Let's say this is going to be 35 as it was here. It is going to be it is going to come inside and it is going to affect the rear visibility criteria.

Now let us take a closer look at the roof and the rear assembly and understand the importance of the ceiling flanks that we always talk about. And also will in this video will understand the shape of the rear rail of the roof outer body. For this purpose, I'll go to clip section and I'll take a section about the zero way region. Now, if you zoom in here and see, here I have the rear door. You have the hinge emboss and the hinge itself and also the other hinge emboss on the roof outer body.

Now, you may be wondering why we have this specific shape for the roof. Now, we have this flange here from the roof outer body and also this flange from the ceiling flange of the rear door. So this will be the surface on which the flange that is the not the flange, it is the rubber sealant that will be placed. So rubber sealant will look something like this when the rear door is in the open condition and it will be compressed and it will take a shape something like this of a potato when the rear door actually closes.

So here we can understand the importance of the ceiling flange. So this ceiling flange data that is the length has to be given as an input to the roof engineer and also the body side. Regarding the body side, we look at it when we actually learn about the body side. As you can see in this view, this is exactly perpendicular to this flange. So only when the rear door engineer gives this as an input to the roof engineer can he design and decide the shape that the roof outer body is going to take at its rear section.

Now also in the previous videos when we learnt about the roof, we actually took this C section and we said this is going to be a clearance when the rear door follows its trajectory. As you can see when the hinge actually works and this goes up this position that is along with the spoiler, the outer panel and the inner panel together, they're going to come down and they will follow this path. So based on this path and this path is going to be given as an input to the roof engineer and he will create this by giving a clearance and he'll create this flange such that it is exactly perpendicular to the ceiling flange.

So usually the rear door and the roof engineers work together and this will be the primary input from each team. They'll also be working together alongside the body side engineers. So this is how they all work together. Now we've talked a lot about the inner panel of the rear door. Now let us get to the outer panel and the windshield. First I'll hide the spoilers. Yes. I'll also hide the inner panel and also the reinforcements. So coming to the outer panel, the outer panel is fairly simple.

It's just going to be the same shape as the styling. Now the most important concept that we have to understand while designing the outer panel is that it is going to have embosses for the snap fitting of the spoilers on the upper and the sides. And then we're going to split the outer panel into two. That is the outer upper and the outer lower and they're going to be hemmed as shown here. How do I connect these two? This is going to be one of my major concerns.

So here we're going to use an operation called laser bracing. Unlike spot welding, laser bracing needs only seven mm flange length. As you can see, this is seven mm. The same goes for the other side as well. And once the outer upper and the outer lower are separated, we decide the position of the number plate. So in this case, this is going to be where my number plate is going to be there. And then the regulation is that every number plate should have a number plate lighting.

If you don't see a lighting on any other car, then it is a violation of the road rules. So we know that we're going to have the number plate here. We'll create this flange. Another button. We have provision for lighting. Now, this can either be on the outer upper or the outer lower. But in this case, it is on the outer upper. Again, the splitting of the outer upper and the outer lower is going to be based on how the rear lights and the number plate is going to be positioned. Let's move on to the windshield. In regards to windshield, it is just one simple thing that we have to understand.

So, when I go to the 0Y region, with respect to the outer panel, the windshield is placed at a distance of about 5 to 7 mm. So, why is this so? Because the windshield being a glass part and the outer panel upper being a sheet metal part. So, these two cannot be in contact with each other. So, for this purpose, we will be placing a rubber material in between and it will ooze out and it will take the place in here. So, all these have to be considered when we design the tailgate assembly, which consists of the outer panel upper, the outer panel lower, which are going to be braced together. And both of them together are going to be hemmed with the inner panel. And then we have the windshield. And also, we have the spoilers.

So, that's it about the modeling of the tailgate assembly. So, that's it for this video guys. In the next video, we look at the other functionalities, the regulations and other considerations while designing the rear door assembly. Thank you.

Want the rest of Automotive BIW Design and Development Part 2 using NXCAD?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Automotive BIW Design and Development Part 2 using NXCAD course

The remaining 39 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Automotive BIW Design and Development Part 2 using NXCAD course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.