Full course · free on YouTube · 45 min

Wiring harness design: free introduction, 45 minutes

A single 45-minute recorded webinar by an industry expert. It goes through the components of a harness, the flow from architecture to harness drawing, the routing process, suppliers, wire and IP standards, thermal management and the 3D tools used.

15 chapters · published 30 Jan 2023 · 54,639 views as of 19 Nov 2026 · by Skill-Lync

Free. We ask for your name and phone once before it plays here · or watch on YouTube ↗

Who is this course for?

Mechanical and automotive engineering students and early-career design engineers who want to know what a vehicle wiring harness contains and what a harness design engineer does.

What will you learn?

  • Name the parts of a wiring harness: wires, connectors, terminals, protection, clips, fuse boxes and guiding channels
  • Tell connectors from terminals and explain what a connector housing, wedge lock and seal do
  • Pick between corrugated tubes, tapes and the three grommet types for a given location
  • Describe the flow from logical architecture and electrical schematics to a harness drawing
  • Follow the routing process from topology and concept routing through design review to proto build
  • Read a wire name such as FLY 0.5 and an IP rating's dust and water digits

What does each part of the course cover?

8 sections, in watching order. Click a timestamp to jump the player there. The video description has no chapter list, so these chapters and timestamps were written from the video itself.

  1. 0:006 min · 4 chapters

    What a wiring harness is: wires, connectors and terminals

    The agenda, then the definition of a harness as an assembly of wires, connectors, terminals, protection, clips, fuse boxes and guiding channels. Covers conductor wires with insulation, connector parts (housing, terminals, wedge locks, seals) and ring and open-tongue terminals with plating.

    Chapters
    • 0:00Introduction and what a wiring harness is
    • 2:07Wires
    • 3:16Connectors
    • 4:43Terminals
  2. 6:265 min · 3 chapters

    Protection: corrugated tubes, grommets and tapes

    Corrugated flexible tubes that protect wires from heat, water, chemicals and physical damage, with colours for identification. Then the three kinds of grommet (sealing for wet-to-dry zone passages, edge protection at doors, vibration absorption near the wheel speed sensor) and insulation tapes.

    Chapters
    • 6:26Protection devices: corrugated tubes
    • 7:39Grommets: sealing, edge protection and vibration
    • 10:02Insulation tapes
  3. 11:177 min · 2 chapters

    Mounting parts, fuse boxes and retention devices

    Cable ties, push-fit clips (round, anti-rotational, fir-tree, anchor), stud clips, edge clips and why they are avoided, adhesive clips and separator clamps. Then fuse and relay boxes, connector secondary locks, back shells and guiding channels.

    Chapters
    • 11:17Cable ties, clips and separator clamps
    • 15:40Fuse and relay boxes, retention devices, guiding channels
  4. 18:4010 min · 2 chapters

    Design flow and the routing process

    The path from logical architecture and electrical schematics to physical architecture, harness routing and the harness drawing. Then the routing process: inputs, wet and dry zones, topology (splitting the harness), concept routing, a digital mock-up design review, proto release and proto build.

    Chapters
    • 18:40From architecture and schematics to the harness drawing
    • 22:00The routing process, review to proto build
  5. 29:056 min · 1 chapter

    Suppliers and wire standards

    Major connector, wire and protection suppliers named in the talk, and why different makers' connectors follow similar specifications. Then wire standards: German DIN and Japanese JASO, and how a name such as FLY 0.5 encodes insulation and nominal cross section.

    Chapters
    • 29:05Suppliers, wire and protection standards
  6. 35:323 min · 1 chapter

    IP rating

    What the Ingress Protection rating is, using phones and earphones as examples. The first digit is dust protection, up to 6, and the second is water protection, which is why the rating matters for parts in a vehicle's wet zones.

    Chapters
  7. 38:312 min · 1 chapter

    Thermal management near the engine

    Why thermal mapping data from the engine maker is needed before routing, how wires to injectors and spark plugs run through the hottest zones, and the use of cotton and nylon tapes and silicone tubes as high-temperature protection.

    Chapters
    • 38:31Thermal management and thermal mapping
  8. 40:395 min · 1 chapter

    The design engineer's work and the 3D tools

    Routing work on the engine area (EGR, pressure and temperature sensors) and body areas such as door panels and the infotainment area. CATIA is named as the main tool, with its electrical part design, electrical harness assembly, installation and flattening workbenches, plus NX.

    Chapters
    • 40:39The design engineer's work, CATIA and NX

Is the Introduction to Wiring Harness course really free?

Yes. All 45 min of it is free on Skill-Lync's YouTube channel, with no payment. To watch it on this page with the chapter guide, leave your name and phone number once; you can also watch it directly on YouTube. It was published on 30 Jan 2023 and had 54,639 views as of 19 Nov 2026. This page adds the chapter guide, a study plan and what to learn next.

How long does the Introduction to Wiring Harness course take to finish?

The video runs 45 min across 15 chapters. At one hour a day that is about 1 days; plan roughly twice that if you practise each exercise as you go. The longest section is "Design flow and the routing process" (10 min), so give it its own days.

Does the free wiring harness course come with a certificate?

The video description has a "claim your certificate" link, which now opens this page. To ask about a certificate for this course, leave your name and phone number in the form below and a Skill-Lync counsellor will call you back. The paid Skill-Lync courses linked here include a certificate along with mentor-reviewed projects.

What should I learn after this course?

The next step is Automotive Wiring Harness using CATIA V5 (free lessons), then Automotive Wiring Harness using CATIA V5 (₹40,000). The free course teaches the concepts; the paid Skill-Lync courses add graded projects, mentor feedback and, in the PG programs, placement support.

What software is used for wiring harness design?

The speaker names CATIA as the main 3D tool used by top OEMs and suppliers, with electrical part design, electrical harness assembly, installation and flattening workbenches, and says NX can also be used. The video only describes them, it does not demonstrate the software or say whether a licence is needed.

Do I need any background before this wiring harness webinar?

The video does not state prerequisites. The speaker calls it a brief introduction and starts from what a harness is, covering wires, connectors, terminals and protection before the design flow. It is a talk with slides and images, not a hands-on modelling session.

What does IP rating mean for a wiring harness?

The speaker explains IP as Ingress Protection, with two digits after IP: the first for dust and the second for water. The highest dust level is 6. Parts in a vehicle's wet zones need a high water digit, and the talk gives EN 60529 as the standard that defines the rating.

Last updated 19 Nov 2026 · Course length, chapters, views and dates from the YouTube video on 19 Nov 2026 · Grow by Skill-Lync: free lessons from every course

Finished the course?

Ask about the certificate or your next course.

Leave your name and phone number. A Skill-Lync counsellor calls you back within one working day about the certificate for Introduction to Wiring Harness and the course that fits where you want to work.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Free full course · Skill-Lync

Start watching

Free, no payment. Leave your name and phone once and the whole Introduction to Wiring Harness course plays here, with every free lesson on Grow. A Skill-Lync counsellor may call you about the certificate or your next course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.